

Li ion charger
Charger for 18 V li-ion battery
- Size
- 130 × 68 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 42
- Nets
- 27
- Pads
- 108
- Tracks, vias
- 245, 14
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 31 Oct 2017
- Updated
- 31 Oct 2017
Overview
Li ion charger is an open-source printed circuit board by ghostwritter91, from the ghostwritter91/Li_ion_charger repository on GitHub. It is a 2-layer board of 130 × 68 mm with 42 parts on 27 nets, routed with 245 tracks and 14 vias.
It is built around the MAX7456, MAX931CPA+ and SS34, with the SI2300DS and SI2323DS among its other parts. Its parts include 12 resistors, 11 capacitors, 6 diodes, 3 transistors and 2 ICs. It belongs with the power boards of this library.
Main components
5MAX7456
UncategorisedMaxim Integrated (Analog Devices)MAX931CPA+
PDIP-8PDIP-8 Comparators ROHSMaxim Integrated (Analog Devices)ComparatorsSS34
SMA(DO-214AC)-55℃~+125℃ 3A 40V 500uA@40V 550mV@3A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky DiodesSI2300DS
SOT-23-3(TO-236-3)-55℃~+150℃ 1 N-channel 1.1W 1.5V 19pF 3.6A 30V 320pF 6.5nC@10V 68mΩ@4.5V SOT-23 MOSFETs ROHSVishay IntertechnologyMOSFETsSI2323DS
SOT-23-3-55℃~+150℃ 1 P-Channel 1.7W 190pF 20V 290pF 39mΩ@4.5V、58mΩ@2.5V 4.1A 450mV 7.8nC@4.5V 740pF SOT-23-3 MOSFETs ROHSTECH PUBLICMOSFETs
README
README.md- Li-ion battery charger (mainly 18V) based on MAX745.
- PCB design for homemade production.
- KiCAD project.
Parts
42| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100nF/50V | Capacitors_SMD:C_0805_HandSoldering | C2, C3, C5, C6, C8, C9 |
| 4 | Mounting_Hole_M6 | M_Holes:MountingHole_6.4mm_M6_reduced | M1, M2, M3, M4 |
| 3 | 100K | Resistors_SMD:R_0805_HandSoldering | R5, R6, R7 |
| 3 | SS34 | Diodes_SMD:DO-214AC | D4, D5, D6 |
| 2 | 11K | Resistors_SMD:R_0805_HandSoldering | R2, R3 |
| 2 | 1K | Resistors_SMD:R_0805_HandSoldering | R8, R11 |
| 2 | SI2300DS | TO_SOT_Packages_SMD:SOT-23 | Q2, Q3 |
| 1 | 0K0 | Resistors_SMD:R_0805_HandSoldering | R9 |
| 1 | 0R1 | Resistors_SMD:R_0805_HandSoldering | R12 |
| 1 | 1.5A | Fuses:Fuse5x20mm | F1 |
| 1 | 1n4148 | Diodes_ThroughHole:Diode_DO-35_SOD27_Horizontal_RM10 | D2 |
| 1 | 22K | Resistors_SMD:R_0805_HandSoldering | R1 |
| 1 | 22uH/2A | Inductors_SMD:DR125 | L1 |
| 1 | 24R | Resistors_SMD:R_0805_HandSoldering | R10 |
| 1 | 470nF/50V | Capacitors_SMD:C_0805_HandSoldering | C4 |
| 1 | 470pF/50V | Capacitors_SMD:C_0805_HandSoldering | C10 |
| 1 | 470uF/35V | Capacitors_ThroughHole:C_Radial_D10_L16_P5 | C1 |
| 1 | 47uF/16V | Capacitors_SMD:c_elec_5x5.7 | C7 |
| 1 | 5K/47K/100K | Resistors_SMD:R_0805_HandSoldering | R4 |
| 1 | 68uF/20V | Capacitors_Tantalum_SMD:TantalC_SizeV_EIA-7343 | C11 |
| 1 | BARREL_JACK_5.5x2.1mm | Connectors:JACK_DC | CON1 |
| 1 | Battery connector | Pin_Headers:Pin_Header_Straight_1x02 | P1 |
| 1 | GREEN | LEDs:LED-3MM | D1 |
| 1 | MAX745 | Housings_SSOP:SSOP-20_5.3x7.2mm_Pitch0.65mm | U2 |
| 1 | MAX931 | SOx:SO8 | U1 |
| 1 | RED | LEDs:LED-3MM | D3 |
| 1 | Si2323DS | TO_SOT_Packages_SMD:SOT-23 | Q1 |
Similar boards
- 2 layers39.3 × 59.9 mm

- 4 layers40 × 40 mm

Atmos fc
cypamigon/atmos_fc
Drone flight controller based on STM32G4 with IMU (ICM-468-P), barometer (DPS-386), OSD (MAX7456) and 32MB flash memory for blackbox logging — running Betaflight.
112 parts1MIT - 4 layers66 × 47 mm

- 2 layers

Copter
arcoslab/open-coroco-legacy
COmpliant RObot COntroller is a free software project aiming to create an impedance controller based on a stm32 microcontroller using bldc motors and strain gauges.
20 parts6 - 2 layers100 × 60 mm

Ppse-2021
thomasnonis/ppse-2021
This is the repository for SALMO, the Solar Azimuth and eLevation Motorized lOcator. It is a PCB used for driving a tracking solar panel system, using GPS location and a MPPT algorithm to maximise the incident power.
133 parts5 - 4 layers75 × 75 mm

USAN r0
alu-source/open_USAN
This project documents the software and hardware of an ultrasonic anemometer, created in cooperation between FH Aachen and DLR Göttingen
262 parts1 - 2 layers75 × 50 mm

- 4 layers50 × 50 mm

Kamikaze drone
Prachannagven/stm32f765-facial-detection
A project built around the STM32F765VIT6 chip to perform basic facial detection and to act as a flight controller for a micro drone.
92 parts1
Questions
How big is the Li ion charger PCB?
It measures 130 × 68 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Li ion charger use?
42 parts, built around the MAX7456, MAX931CPA+, SS34 and SI2300DS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Li ion charger KiCad files?
From the ghostwritter91/Li_ion_charger repository on GitHub, at the commit this page was made from: the board is li_ion_charger.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Li ion charger design in my own project?
Its repository states no licence, so its author keeps all rights: ask ghostwritter91 before reusing the design.