

Aquarius plus
Official Aquarius+ repository
- Size
- 128 × 83 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 115
- Nets
- 186
- Pads
- 540
- Tracks, vias
- 1,887, 323
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 20 Jan 2022
- Updated
- 19 Sep 2026
Overview
Aquarius plus is an open-source printed circuit board by fvdhoef, from the fvdhoef/aquarius-plus repository on GitHub, published under the MIT licence. It is a 2-layer board of 128 × 83 mm with 115 parts on 186 nets, routed with 1,887 tracks and 323 vias.
It is built around the XC6SLX9-2TQG144C, ESP32-S3-WROOM-1-N4R2 and TF-03A, with the IP4234CZ6, IS61C5128AL-10TLI and LD1117S12 among its other parts. Its parts include 47 capacitors, 36 resistors, 7 connectors, 6 ICs and 1 diode. It belongs with the ESP32 and FPGA and CPLD boards of this library.
Main components
8XC6SLX9-2TQG144C
LQFP-144(20x20)0℃~+85℃ 9152 LQFP-144(20x20) Programmable Logic Device (CPLDs/FPGAs) ROHSAMD/XILINXProgrammable Logic Device (CPLDs/FPGAs)ESP32-S3-WROOM-1-N4R2
SMD,25.5x18mm-103.5dBm -40℃~+85℃ 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 On-board PCB Antenna UART、SPI、I2C、GPIO、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesTF-03A
SMD100V 2.76mm Connector and Ejector No Push-Push Standard SD Card SMD SD Card / Memory Card Connector ROHSHRO ElectronicsSD Card / Memory Card ConnectorIP4234CZ6
TSOP-6-40℃~+85℃@(Ta) 100W 100nA 3.1pF 5.5V 6V ESD Four channels IEC 61000-4-2、IEC 61000-4-5 TSOP-6 ESD and Surge Protection (TVS/ESD) ROHSNexperiaESD And Surge Protection (TVS/ESD)IS61C5128AL-10TLI
TSOPII-44-40℃~+85℃ 10ns 12mA 4.5V~5.5V 4Mbit 55mA Auto power-down function TSOPII-44 SRAM ROHSISSISRAMLD1117S12
SOT-223-30.003%Vout 0℃~+125℃@(Tj) 1 1.2V 15V 1V@(100mA) 60uA 75dB@(120Hz) 800mA Fixed Over Current Protection、Thermal shutdown Positive SOT-223-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLDL1117S33R
SOT-223-4-40℃~+125℃@(Tj) 1 1.2A 18V 3.3V 500uA 600mV@(1.2A) 60uVrms 87dB@(120Hz) Fixed Over Current Protection、Thermal Shutdown Positive SOT-223-4 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsSX3M14.31818M20F30TNN
SMD3225-4P-40℃~+85℃ 1.62V~3.63V 10mA 14.31818MHz CMOS ±20ppm ±30ppm SMD3225-4P Crystal Oscillators ROHSShenzhen SCTF ElecCrystal Oscillators
README
README.md
Next-generation Z80-based retro computer system
Documentation
For documentation, please take a look at the Wiki.
Abstract:
What would the Aquarius have evolved into if Mattel hadn't abandoned the system back in 1984? The Aquarius+ is the next-generation of Z80-based 8-bit hardware for the Aquarius platform. The intent is to deliver a cost-effective, backwards-compatible retro computer system that both developers and nostalgists will love and use, all in the spirit of the original, orphaned Aquarius platform.

Features:
- Backward compatibility with existing Aquarius hardware and software
- Modern, flexible video solution that supports bitmapped graphics, sprites, and tiles, delivered through clean VGA output
- Dual AY sound chips (virtual) for six sound voices
- 512kb of paged RAM in four 16k banks
- Reworked SYSROM and programmable CHARROM
- Integrated SD card and commands (remove dependency on cassette loading)
- WiFi connectivity
- Bluetooth connectivity for modern game controllers
Folder structure
| Directory | Description |
|---|---|
| EndUser | These files are meant for the normal end-user, that just wants to play and work with the system. You can find some nice sample programs, games and music to run on system here. |
| Maker | Files required for makers to manufacture and assemble an Aquarius+ system. |
| SDK | If you want to develop your own software for the Aquarius+, look here. |
| System | This contains all other files related to the system, including: Schematics/PCB, FPGA, ESP32, Emulator |
Parts
115| Qty | Value | Footprint | References |
|---|---|---|---|
| 27 | 100nF | Capacitor_SMD:C_0603_1608Metric | C12, C13, C14, C15, C16, C17, C19, C21, C23, C24, C27, C28, C29, C30, C31, C32 +11 |
| 13 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C9, C10, C11, C18, C22, C25, C26, C35, C38, C39, C41, C43, C47 |
| 7 | 10k | Resistor_SMD:R_0603_1608Metric | R24, R25, R26, R28, R30, R33, R34 |
| 5 | 100 | Resistor_SMD:R_0603_1608Metric | R22, R27, R29, R31, R32 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 1070 | Resistor_SMD:R_0603_1608Metric | R8, R12, R16 |
| 3 | 2150 | Resistor_SMD:R_0603_1608Metric | R9, R13, R17 |
| 3 | 4300 | Resistor_SMD:R_0603_1608Metric | R10, R14, R18 |
| 3 | 536 | Resistor_SMD:R_0603_1608Metric | R7, R11, R15 |
| 3 | Fiducial | Fiducial:Fiducial_1mm_Mask2mm | FID1, FID2, FID3 |
| 2 | 0 | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | 1 | Resistor_SMD:R_0603_1608Metric | R23, R36 |
| 2 | 100uF | Capacitor_SMD:CP_Elec_6.3x7.7 | C3, C8 |
| 2 | 10uF | Capacitor_SMD:C_0805_2012Metric | C4, C6 |
| 2 | 150 | Resistor_SMD:R_0603_1608Metric | R3, R5 |
| 2 | 220 | Resistor_SMD:R_0603_1608Metric | R21, R35 |
| 2 | 220 | Inductor_SMD:L_0603_1608Metric | FB1, FB2 |
| 2 | 330 | Resistor_SMD:R_0603_1608Metric | R4, R6 |
| 2 | 820 | Resistor_SMD:R_0603_1608Metric | R19, R20 |
| 2 | DNP | Capacitor_SMD:C_0603_1608Metric | C1, C2 |
| 2 | USB | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP1, JP2 |
| 1 | 22uF | Capacitor_SMD:C_1206_3216Metric | C20 |
| 1 | 2N7002 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | Audio out | aquarius-plus:C2939180 | J3 |
| 1 | Bootloader | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP4 |
| 1 | DBG | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP3 |
| 1 | ESP USB Host | Connector_USB:USB_A_Molex_67643_Horizontal | J2 |
| 1 | ESP32 spare | Connector_PinHeader_2.54mm:PinHeader_2x07_P2.54mm_Vertical | J5 |
| 1 | ESP32-S3-WROOM-1-N4R2 | aquarius-plus:ESP32-S2-SOLO-N4R2 | U2 |
| 1 | FPGA spare | Connector_PinHeader_2.54mm:PinHeader_2x06_P2.54mm_Vertical | J7 |
| 1 | IP4234CZ6 | Package_TO_SOT_SMD:TSOT-23-6 | U1 |
| 1 | IS61C5128AL-10TLI | Package_SO:TSOP-II-44_10.16x18.41mm_P0.8mm | U5 |
| 1 | LD1117S12 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | LDL1117S33R | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U6 |
| 1 | Power in | aquarius-plus:AMPHENOL_10118194-0001LF | J1 |
| 1 | SD act. | LED_THT:LED_D3.0mm_Horizontal_O1.27mm_Z2.0mm | D1 |
| 1 | SW_DPDT_x2 | Button_Switch_THT:SW_E-Switch_EG2219_DPDT_Angled | SW1 |
| 1 | SX3M14.31818M20F30TNN | Oscillator:Oscillator_SMD_SeikoEpson_SG8002CE-4Pin_3.2x2.5mm | X1 |
| 1 | TF-03A | aquarius-plus:TF-03A | J6 |
| 1 | USB Choke | Inductor_SMD_Wurth:WE-CNSW_08058 | L1 |
| 1 | VGA | aquarius-plus:ICD15S13E4GV00LF | J4 |
| 1 | XC6SLX9-2TQG144C | Package_QFP:TQFP-144_20x20mm_P0.5mm | U4 |
The 114 most common of 115 parts.
More from fvdhoef/aquarius-plus
7- 2 layers167 × 115 mm

- 2 layers319.5 × 146.3 mm

- 2 layers167 × 115 mm

- 2 layers128 × 83 mm

- 4 layers141 × 89.5 mm

- 4 layers84.3 × 69.8 mm

- 2 layers51.9 × 44.4 mm

Similar boards
- 4 layers65 × 56 mm

- 2 layers66.1 × 62.2 mm

Mimas
numato/samplecode
This repository contains sample code for different Numato Lab products
99 parts144 - 4 layers89 × 61 mm

Spartan6Dev
jonthomasson/SpartanMini
A flexible, simple, yet powerful FPGA development board.
186 parts17 - 4 layers100 × 80 mm

- 2 layers99 × 58.5 mm

- 4 layers100 × 64 mm

S6la8
OutBlade/s6la8
Open-source 8-channel logic analyzer: FX2LP + Spartan-6, with a sigrok driver. Design in progress, not yet built or tested.
155 parts1 - 2 layers89.2 × 99 mm

- 4 layers160 × 100.2 mm

Csa ultracpu
fachat/csa_ultracpu
The CPU board for a 17MHz Colour-PET clone with modern interfaces
175 parts9GPL-3.0
Questions
How big is the Aquarius plus PCB?
It measures 128 × 83 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Aquarius plus use?
115 parts, built around the XC6SLX9-2TQG144C, ESP32-S3-WROOM-1-N4R2, TF-03A and IP4234CZ6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Aquarius plus KiCad files?
From the fvdhoef/aquarius-plus repository on GitHub, at the commit this page was made from: the board is System/pcb/mini/mini_rev1/aquarius-plus.kicad_pcb and its schematic System/pcb/mini/mini_rev0/aquarius-plus.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Aquarius plus design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).