Skip to the content
4 layers35.2 × 53.5 mmKR260eLinkHat, the printed circuit board in 3D

This repository accompanies the master's thesis “Development of an MPSoC-based readout board as a verification method and interface for the ATLAS ITk MOPS-Hub communication interface” (2024).

Size
35.2 × 53.5 mm
Copper layers
4
Thickness
1 mm
Parts
32
Nets
60
Pads
200
Tracks, vias
534, 63
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
13 Oct 2026
Updated
14 Oct 2026

Overview

KR260eLinkHat is an open-source printed circuit board by fsnitz, from the fsnitz/ATLAS-ITk-MOPS-Hub-readout-prototype repository on GitHub, published under the MIT licence. It is a 4-layer board of 35.2 × 53.5 mm with 32 parts on 60 nets, routed with 534 tracks and 63 vias.

Its parts include 16 resistors, 10 capacitors, 3 connectors and 2 ICs.

README

README.md

MPSoC-based MOPS-Hub readout board — supplementary project files

This repository accompanies the master's thesis “Development of an MPSoC-based readout board as a verification method and interface for the ATLAS ITk MOPS-Hub communication interface” (2024).

The work addresses an intermediate readout system for the ATLAS Inner Tracker (ITk) Pixel Detector Control System. It uses the AMD Kria K26 System-on-Module (SoM) with programmable logic (PL) and a processing system (PS), PetaLinux, an AXI-based shared-memory interface, and an electrical link (eLink) to communicate with the MOPS-Hub. The eLink is the electrical communication link; the eLink Core is its FPGA firmware implementation.

Project status: The PL–PS shared-memory interface was successfully tested. The eLink interface exhibited firmware-timing and hardware/signal-integrity limitations. Full readout-chain functionality was not verified within the thesis. The published files should therefore be treated as research and development artifacts, not as a validated production design.

Before publishing this repository: Copy the actual project files into the paths listed below, preserving capitalization and filenames. These links are derived from the original thesis appendix and cannot be verified until the repository has been populated. Check that you have permission to redistribute third-party documentation, vendor files, externally developed tools, and CERN/project-specific materials. If a file cannot be released, remove its repository link and cite the authorized upstream source instead.

Getting started

  1. Consult the thesis for the system architecture, implementation decisions, test setup, results, and limitations.
  2. For Vivado project generation, start with the firmware build instructions and the relevant build script below. The thesis used the 2023.2 versions of Vivado and PetaLinux; confirm any additional requirements in the build instructions.
  3. For embedded Linux, see the PetaLinux projects and associated tools under ToolsAndLibs.
  4. For the eLink adapter, see the KR260 eLink-hat revisions. The second revision includes changes for receiver-side common-mode biasing.
  5. Use a tagged release of this repository when reproducing the thesis, because its main development branch may change over time.

Repository contents

This README is the index of the supplementary materials.

The five principal directories are Hardware/, Firmware/, Software/, Documentation/, and Miscellaneous/. Links below are relative to the root of this repository.

Hardware

Firmware

Software

  • Software/PetaLinuxProjects/ — files for preparing the KR260 embedded Linux systems, including the necessary BSP and hardware design resources as described in the thesis.
    • PLtoPS_Test/ — shared-memory interface test (thesis Section 7.1).
    • MopsHubReadoutBoard/ — readout board and proposed full-chain test project (thesis Section 7.3). The corresponding register map and hardware-access files are associated with this project.
    • K26_StarterKit/ — starter BSP files from which the thesis projects were derived.
    • epos-rootfs/ — AlmaLinux 9-based root filesystem materials.
  • Software/ToolsAndLibs/ — supporting tools and libraries.
    • xsa-to-overlays/ — Python tool for preparing Device Tree-related files from a hardware design.
    • PuzzledLizardWizard/ — Python tool for generating a Hardware Access Library (HAL) from a register-map JSON file.
    • libuio-bugFix/ — library files for user-space I/O access under embedded Linux.

The original appendix additionally mentions a HalFiles subdirectory inside the PetaLinux projects, but does not establish its full relative path. Add a direct link here after confirming its location in the repository.

Documentation

Miscellaneous

Reproducibility and release information

Record the version/tag used for each public thesis release, along with relevant dependencies, hardware revisions, and tool versions. If possible, identify the exact PP3-FPGA firmware configuration used for each test. When a stable release is available, archive it in a long-term research repository and cite the corresponding persistent identifier in the published thesis.

The root directory and file names above follow the original digital appendix. Only the thesis appendix was supplied for this README; the supplementary hardware, firmware, software, and documentation files themselves have not been inspected or validated in this draft.

Citation

Thesis: Felix Sebastian Nitz, Development of an MPSoC-based readout board as a verification method and interface for the ATLAS ITk MOPS-Hub communication interface, Master's thesis, Cologne University of Applied Sciences, 2024.

Repository: Cite the released repository version and its eventual DOI or version-specific URL when available. Add a CITATION.cff file once the repository metadata and release details are finalized.

Parts

32
QtyValueFootprintReferences
1010nFCapacitor_SMD:C_0201_0603MetricC1, C2, C3, C4, C5, C6, C7, C8, C9, C10
510KResistor_SMD:R_0201_0603MetricR4, R7, R8, R11, R12
547KResistor_SMD:R_0201_0603MetricR3, R5, R6, R9, R10
2100KResistor_SMD:R_0201_0603MetricR13, R15
2100RResistor_SMD:R_0201_0603MetricR1, R2
256KResistor_SMD:R_0201_0603MetricR14, R16
2RJ45_ShieldedReadoutBoard_Footprints:WR-MJ Modular Jack Horizontal Shielded_615008140621J2, J3
1PinSocket_2x20_P2.54mmReadoutBoard_Footprints:RpiHatJ1
1SN65LVDS047DRPackage_SO:SOIC-16_3.9x9.9mm_P1.27mmU2
1SN65LVDS050DRReadoutBoard_Footprints:SOIC127P600X175-16NU1
1~ReadoutBoard_Footprints:PinguinLogolog1

More from fsnitz/ATLAS-ITk-MOPS-Hub-readout-prototype

1
  • 4 layers35.2 × 53.5 mmKR260eLinkHat, the printed circuit board in 3D

    KR260eLinkHat

    fsnitz/ATLAS-ITk-MOPS-Hub-readout-prototype

    This repository accompanies the master's thesis “Development of an MPSoC-based readout board as a verification method and interface for the ATLAS ITk MOPS-Hub communication interface” (2024).

    28 partsMIT

Similar boards

  • 4 layers15.3 × 10.8 mmAkl ad4, the printed circuit board in 3D

    Akl ad4

    azonenberg/starshipraider

    Open hardware test equipment

    32 parts193BSD-3-Clause
  • 4 layers45.3 × 53.3 mmAntenna switch, the printed circuit board in 3D

    Antenna switch

    matthuszagh/fmcw

    6GHz frequency-modulated continuous-wave radar with real-time range detection

    32 parts66Apache-2.0
  • 4 layers34.6 × 25 mmAmiga DB23 video adapter, the printed circuit board in 3D

    Amiga DB23 video adapter

    jbilander/Amiga_DB23_video_adapter

    A PCB for creating Amiga SCART or Amiga VGA cables. You can also use this adapter to feed a new clock to the Amiga via XCLK making your machine true PAL/NTSC switchable

    32 parts42CC-BY-SA-4.0
  • 4 layers44.8 × 12.5 mmHellen1-mcz33810, the printed circuit board in 3D

    Hellen1-mcz33810

    andreika-git/hellen-one

    Hellen-One Hardware Platform for rusEFI Engine Management System

    32 parts38
  • 4 layers88.9 × 88.9 mmFlight Controller, the printed circuit board in 3D

    Flight Controller

    sondrehr/Flight_Controller

    The code used on my STM32 diy drone flight controller

    32 parts36
  • 4 layers32.9 × 100 mmFilters, the printed circuit board in 3D

    Filters

    greatscottgadgets/misc

    miscellaneous Great Scott Gadgets projects

    32 parts21GPL-2.0
  • 4 layers113.3 × 23.5 mmTinyriser6, the printed circuit board in 3D

    Tinyriser6

    a-little-wifi/Tinyriser6

    Tinyriser for the Tiny6 and Tiny7 generations of Lenovo Tiny PCs

    32 parts17CERN-OHL-S-2.0
  • 4 layers22 × 18.5 mmHc32l110, the printed circuit board in 3D

    Hc32l110

    Aightech/CleverHand-hardware

    32 parts17GPL-3.0

Questions

How big is the KR260eLinkHat PCB?

It measures 35.2 × 53.5 mm and has 4 copper layers, 1 mm thick.

What parts does the KR260eLinkHat use?

32 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the KR260eLinkHat KiCad files?

From the fsnitz/ATLAS-ITk-MOPS-Hub-readout-prototype repository on GitHub, at the commit this page was made from: the board is Hardware/KR260eLinkHat/rev02/KR260eLinkHat.kicad_pcb and its schematic Hardware/KR260eLinkHat/rev01/KR260eLinkHat.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the KR260eLinkHat design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).