
Nrf bga
github-linguist/linguist
Language Savant. If your repository's language is being reported incorrectly, send us a pull request!

Arty A7 FPGA
Arty a7-fpga is an open-source printed circuit board by FabienMeyer, from the FabienMeyer/arty-a7-fpga repository on GitHub, published under the MIT licence. It is a 2-layer board of 111.8 × 83.8 mm with 12 parts on 35 nets.
Its parts include 4 resistors and 4 connectors. It belongs with the fPGA and programmable logic boards of this library.
Design a professional-grade Arduino-based Fan Controller and Power Management system for a custom PCB. The device manages three high-end 12V PWM fans and features a full battery backup (UPS) system.
Physical Configuration:
Control Box (3D Printed): Houses the Arduino Nano, 16x2 LCD, PEC11 Encoder, Battery Pack, and an Internal Safety Temperature Sensor.
Fan Housing (Wood): Houses 3x 12V PWM fans and a Deported Environmental Sensor (Temperature, Humidity, Pressure) for ambient weather data.
Dual-Input Power Path: - Primary: 15V DC Wall Adapter.
Load Sharing: Run fans/logic and charge the battery simultaneously. Seamless switching to battery when unplugged.
Logic Rail: High-efficiency Step-Down (Buck) regulation to 5V for logic components.
Battery Monitoring: I2C-based sensing for real-time Voltage, Current (mA), and Power (Watts).
Capacity Assumption: 6000mAh (3S2P configuration).
Thermal Safety: Monitor the Internal Control Box Temperature. If the internal electronics/battery compartment exceeds a safe threshold (e.g., 55°C), trigger an alert or shutdown.
Hardware Protection: Implementation of a 3S BMS (Battery Management System).
Software-Controlled Safety Switch: High-Side Load MOSFET controlled by Arduino (Pin D6) to disconnect power if:
Critical Undervoltage (<9.6V).
Overcurrent/Short-circuit (>2A).
Critical Internal Overheat.
Fan Control: 3x Fans on Pin D9. 25kHz Ultrasonic PWM (Timer 1) for silent operation.
User Interface:
Input: PEC11 Rotary Encoder with push-button (D2/D3/D5).
Display: 16x2 LCD via I2C.
Dual-Zone I2C Sensors:
Sensor A (Internal): Temperature only (for box safety).
Sensor B (Remote): Temperature, Humidity, Pressure (Deported to the wooden fan housing).
Power Saving (Night Mode):
LCD backlight controlled via MOSFET on Pin D4.
30-second inactivity timeout; wake on encoder interaction.
Navigation: Rotate encoder to scroll through pages:
Weather (Remote): Ambient Temp, Humidity, Pressure.
System Health (Internal): Box Temp, Battery Voltage, Current Draw, and "Time Remaining."
Fan Pages (1-3): Individual speed and status for each fan.
Interaction: Short Press to Edit Speed (0-100%); Long Press (1s) to Toggle Fan ON/OFF.
Fault Handling: If a fault (Overheat/Overcurrent/Low-V) is detected, pull D6 LOW and display specific error.
Component Proposals: Specific high-efficiency parts for the 3S Charger, Power Path, Current Sensor, Buck Regulator, and MOSFETs.
Dual-Sensor Strategy: Propose the best I2C sensors to avoid address conflicts (e.g., using different addresses or an I2C multiplexer).
Firmware: Complete, non-blocking Arduino C++ code (.ino) including 25kHz PWM and safety logic.
Wiring/PCB Guidance: Advice on routing the deported I2C sensor to the wooden box over a distance while maintaining signal integrity (pull-up resistor placement).
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1, R2, R3, R4 |
| 4 | Fan_4pin | Connector:FanPinHeader_1x04_P2.54mm_Vertical | M1, M2, M3, M4 |
| 4 | PmodHeader_2x06 | arty_a7_fpga:PmodHeader_2x06_P2.54mm_Horizontal | J1, J2, J3, J4 |

github-linguist/linguist
Language Savant. If your repository's language is being reported incorrectly, send us a pull request!


google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards



hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

VoronDesign/Voron-Tap
Tap is a nozzle-based z-probe for the V2 and Trident printer designs. The entire toolhead moves to trigger an optical switch. Tap offers many advantages:

stacksmashing/pico-tpmsniffer
A simple, very experimental TPM sniffer for LPC bus
It measures 111.8 × 83.8 mm and has 2 copper layers, 1.6 mm thick.
12 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the FabienMeyer/arty-a7-fpga repository on GitHub, at the commit this page was made from: the board is pcb/arty_a7_fpga.kicad_pcb and its schematic pcb/arty_a7_fpga.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).