
Cosmonode ext02
exostic/Cosmonode_PCBs
Kicad plans to design a base node as the main PCB. It also contains extensions adapted for different set of sensors/connectors.

Kicad plans to design a base node as the main PCB. It also contains extensions adapted for different set of sensors/connectors.
Cosmonode ext01 is an open-source printed circuit board by exostic, from the exostic/Cosmonode_PCBs repository on GitHub. It is a 2-layer board of 12.7 × 10.2 mm with 8 parts on 7 nets, routed with 20 tracks and 3 vias.
It is built around the SI7020-A20-YM0R. Its parts include 6 connectors, 1 capacitor and 1 IC. It belongs with the sensors and measurement boards of this library.
Universal node, plug and play extensions to ease sensors connection.
## Features
- Compile and flash with Arduino IDE
- MCU = ATMega328P-AU
- radio = RN2483 / RFM69CW ( communications based on LoRaWan or MySensors protocol )
- 3.3V regulation ( XC6206P332MR )
- Powered by 3.7V LiPo battery ( 2 pins JST connector )
- Battery charging ( MCP7831 )
- State LED's
- Jumpers to activate radio reset, LED's, on/off switch
- Button for reset / config mode, or anything else!
- ATSHA204 to allow hardware unique signature ( no use with RN2483 )## Projects
Each directory contains Kicad plans, 3D plans, gerber, descriptive .png and .pdf files.
- ext01 : BME280, Temperature + Humidity + Pression sensor ( only here for the footprint )
- ext02 : XKC-Y25, Liquid level sensor
- ext03 : Various connectors ( I2C, Digital, Analog )
- ext04 : PT100 3 wire, Temperature sensor
- ext05 : ISP header + micro USB to TTL
- ext06 : Analog pH Sensor - BNC probe (WIP)
- ext07 : MHZ19, CO2 sensorA0 = /
A1 = /
A2 = ATSHA204 Input
A3 = Battery voltage report
A4 = SDA
A5 = SCL
A6 = * LED, jumper J9 ( used as RN2483 Tx )
A7 = * LED, jumper J14 ( used as RN2483 Rx )
D0 = RX
D1 = TX
D2 = * WakeInterrupt from RN2483, jumper J6 - RFM69 DI0
D3 = ButtonInterrupt, jumper JP2 ( used to chose mode )
D4 = /
D5 = /
D6 = /
D7 = /
D8 = /
D9 = * RN2483 Reset, jumper J3 - RFM69 Reset
D10 = RN2483 Rx - RFM69 NSS
D11 = RN2483 Tx - RFM69 MOSI
D12 = RFM69 MISO
D13 = RFM69 SCK
*optionnal, solder jumper## Roadmap
--> changelog.md
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | CONN_01X01 | Wire_Pads:SolderWirePad_single_1-2mmDrill | J2, J4, J5, J6 |
| 1 | 100nF | Capacitors_SMD:C_0603_HandSoldering | C1 |
| 1 | CONN_01X04 | Pin_Headers:Pin_Header_Angled_1x04_Pitch2.54mm | J1 |
| 1 | GS3 | Connectors:GS3 | J3 |
| 1 | SI7020-A20-YM0R | SI7020-A20-YM0R:SON100P300X300X80-7N | U1 |

exostic/Cosmonode_PCBs
Kicad plans to design a base node as the main PCB. It also contains extensions adapted for different set of sensors/connectors.

getlarge/Cosmonode_PCBs
Kicad plans to design a base node, also contains extensions adapted for different set of sensors/connectors.


joeycastillo/Sensor-Watch
A board replacement for the classic Casio F-91W wristwatch

rusefi/rusefi
rusefi - GPL internal combustion engine control unit

hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

shanteacontrols/OpenDeck
A platform for building interactive control and sensing devices using MIDI and OSC built with Zephyr RTOS.

hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

dangiu/PicoMemcard
Emulating PSX Memory Card (or controller) using a Raspberry Pi Pico
It measures 12.7 × 10.2 mm and has 2 copper layers, 1.6 mm thick.
8 parts, built around the SI7020-A20-YM0R. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the exostic/Cosmonode_PCBs repository on GitHub, at the commit this page was made from: the board is Cosmonode_ext01/Cosmonode_ext01.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask exostic before reusing the design.