Skip to the content
2 layers94.7 × 64.5 mmController, the printed circuit board in 3D

Welcome to the BYU Classroom Robotics project. It was built for the as a 2024 Immerse Broader Impacts Project by Ethan Hunter and Ephraim.

Size
94.7 × 64.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
10
Nets
38
Pads
72
Tracks, vias
79, 0
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
24 Jun 2024
Updated
4 Sep 2024

Overview

Controller is an open-source printed circuit board by ethan-ejh-hunter, from the ethan-ejh-hunter/byu-classroom-robotics repository on GitHub. It is a 2-layer board of 94.7 × 64.5 mm with 10 parts on 38 nets, routed with 79 tracks and 0 vias.

Its parts include 4 diodes, 3 ICs, 2 switches and 1 connector.

README

README.md

BYU Classroom Robotics

Introduction

Welcome to the BYU Classroom Robotics project. It was built for the as a 2024 Immerse Broader Impacts Project by Ethan Hunter and Ephraim.

It utelizes a Rpi Pico for the main board and ESP32s for the controllers. Many features should move over to any other micropython based board, though the actual boards would need redesign.

Most of the files are not used in the actual robots! They are simply there as documenting the journey, and maybe helping give some basic examples for how to use some of the libraries.

The two you'll want to look at is main.py, for the main board and controller.py. Each board will also need to have ble_advertising.py copied to the board. The joystick will need joystick_channel.py as well.

The controller allows switching between tank drive & one joystick driving. The default is tank drive. It displays an animation when switching on the controller.

Each controller must be assigned a number. Make sure to put a file called "dev_name" with the number on the flash as well. When the controller and the robot connect, they will both light up the controller number in binary on the included LEDs.

The pairing is only... partially done. There's a few options I see for it now. Currently, the pairing code only really allows for one controller + one robot. I never got around to rewriting the bluetooth scan code for it to find a list of all bluetooth devices and than iterate thru them. The way I see it working is that the main board is constantly advertising how many connections it has. The controllers will cycle thru all available connections. When it connects to one, it checks to see if it has 1 or 0 connections. Then it waits a random amount of time, and then if it still says it's only connected to one, it "locks in." If another one is connected after that time, it flips a coin, 25% it switches. If it doesn't switch, it waits a random amount of time, and then switches again. Overall, they should all find their own connections eventually. It is already set up to transmit the controller number, and the main board transmits how many devices are connected.

The main board uses a seperate smaller board for the LEDs. The controller has them built in.

Parts

10
QtyValueFootprintReferences
4SFH4346LED_THT:LED_D3.0mm_IRBlackD1, D2, D3, D4
2SW_PushButton_Switch_SMD:SW_Push_1P1T_NO_CK_PTS125Sx43PSMTRSW1, SW2
2~joystick:B10k-1U1, U2
1Screw_Terminal_01x02lab:2 wide through hole .5cmJ1
1~lab:ESP32-wroomU3

More from ethan-ejh-hunter/byu-classroom-robotics

2
  • 2 layers57.2 × 58.2 mmByu classroom robotics, the printed circuit board in 3D

    Byu classroom robotics

    ethan-ejh-hunter/byu-classroom-robotics

    Welcome to the BYU Classroom Robotics project. It was built for the as a 2024 Immerse Broader Impacts Project by Ethan Hunter and Ephraim.

    13 parts
  • 2 layers51.1 × 23.1 mmLED board, the printed circuit board in 3D

    LED board

    ethan-ejh-hunter/byu-classroom-robotics

    Welcome to the BYU Classroom Robotics project. It was built for the as a 2024 Immerse Broader Impacts Project by Ethan Hunter and Ephraim.

    5 parts

Similar boards

  • 2 layers57 × 55.2 mmLogicAnalyzer, the printed circuit board in 3D

    LogicAnalyzer

    gusmanb/logicanalyzer

    24 channel, 100Msps logic analyzer hardware and software

    10 parts5.1kGPL-3.0
  • 2 layers32.2 × 15.4 mmProtector, the printed circuit board in 3D

    Protector

    byrantech/laptop

    anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

    10 parts4.3kMIT
  • 2 layers26 × 18 mmConn, the printed circuit board in 3D

    Conn

    yaqwsx/KiKit

    Automation tools for KiCAD

    10 parts2.1kMIT
  • 2 layers44.3 × 30.5 mmLime2-SATA RevA, the printed circuit board in 3D

    Lime2-SATA RevA

    OLIMEX/OLINUXINO

    OLINUXINO is Open Source / Open Hardware, low cost from EUR 24 Linux Industrial grade Single Board Computer capable to operate -25+85C

    10 parts1.5k
  • 2 layers17.8 × 43.2 mmNano Adapter, the printed circuit board in 3D

    Nano Adapter

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    10 parts1.1kGPL-3.0
  • 2 layers53.9 × 23.2 mmBuffer, the printed circuit board in 3D

    Buffer

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    10 parts1kGPL-3.0

Questions

How big is the Controller PCB?

It measures 94.7 × 64.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Controller use?

10 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Controller KiCad files?

From the ethan-ejh-hunter/byu-classroom-robotics repository on GitHub, at the commit this page was made from: the board is Controller/controller/controller.kicad_pcb and its schematic Controller/alternate-version/alternate-controller-version/alternate-controller-version.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Controller design in my own project?

Its repository states no licence, so its author keeps all rights: ask ethan-ejh-hunter before reusing the design.