embediver/atx-wled-controller1A ESP-07 based controller to use with WLED and ATX power supplies.
Wled controller is an open-source printed circuit board by embediver, from the embediver/atx-wled-controller repository on GitHub. It is a 2-layer board of 100 × 40 mm with 45 parts on 27 nets, routed with 235 tracks and 32 vias.
It is built around the ESP-07, 74HCT00D and LM1117-3.3, with the LL4148 and BC817 among its other parts. Its parts include 10 resistors, 8 capacitors, 7 diodes, 5 ICs and 3 connectors. It belongs with the ESP8266 boards of this library.
Designed to work with all kinds of single wire adressable NeoPixel LEDs and ATX Power supplies.
It's intended to be uesed with ATX power supplies (since they are so easy availible), where it can be driven over the 5V always-on rail. By powering the LED's with the other Rails, they can be switched off together with the PS.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C3, C5, C6, C7, C8 |
| 6 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3, R4, R5, R9 |
| 6 | LL4148 | Diode_SMD:D_MiniMELF | D2, D3, D4, D5, D6, D7 |
| 3 | 62R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6, R7, R8 |
| 2 | 220u | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C1, C4 |
| 2 | SW_Push | Button_Switch_THT:SW_PUSH_6mm_H13mm | SW1, SW2 |
| 1 | 1N5817 | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D1 |
| 1 | 1k2 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R10 |
| 1 | 74HCT00 | Package_SO:SO-14_3.9x8.65mm_P1.27mm | U2 |
| 1 | BC817 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | Conn_01x05_Male | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J3 |
| 1 | ESP-07 | ESP8266:ESP-07v2 | U3 |
| 1 | LM1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | LOGO | WHSlogo:WHLOGO | G*** |
| 1 | Screw_Terminal_01x04 | TerminalBlock_4Ucon:TerminalBlock_4Ucon_1x04_P3.50mm_Horizontal | J1 |
| 1 | Screw_Terminal_01x06 | TerminalBlock_4Ucon:TerminalBlock_4Ucon_1x06_P3.50mm_Horizontal | J2 |
| 1 | TSOP17xx | OptoDevice:Vishay_CAST-3Pin | U5 |
| 1 | TSOP45xx | OptoDevice:Vishay_MOLD-3Pin | U4 |
The 37 most common of 45 parts.
It measures 100 × 40 mm and has 2 copper layers, 1.6 mm thick.
45 parts, built around the ESP-07, 74HCT00D, LM1117-3.3 and LL4148. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the embediver/atx-wled-controller repository on GitHub, at the commit this page was made from: the board is wled-controller.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask embediver before reusing the design.
kwiecinski/BMS-and-offgrid-photovoltaic-management-system
Project contains BMS for lead-acid batteries and ESP-based board used to pull information from EASUN offgrid inverter, energy meters and sensors.
sikaxn/FRC-Custom-CAN-Sensor
If you are looking for IronMaple ESP32‐FRC‐devkit resources, please switch branch to dev-board.
