

STM32L433CBT Dev Board
Repository for PCB Design Projects
- Size
- 30.2 × 50.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 34
- Nets
- 64
- Pads
- 212
- Tracks, vias
- 695, 31
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 27 Feb 2020
- Updated
- 26 May 2021
Overview
STM32L433CBT Dev Board is an open-source printed circuit board by embeddedalpha, from the embeddedalpha/PCB-Design repository on GitHub, published under the MIT licence. It is a 2-layer board of 30.2 × 50.3 mm with 34 parts on 64 nets, routed with 695 tracks and 31 vias.
It is built around the CP2102N-A01-GQFN24 and W25Q128JVSIQ. Its parts include 13 capacitors, 4 diodes, 4 connectors, 3 resistors and 2 ICs. It belongs with the microcontroller boards and interfaces and adapters boards and the STM32 boards of this library.
Main components
2CP2102N-A01-GQFN24
QFN-24-EP(4x4)3Mbps 3V~3.6V Transceiver QFN-24-EP(4x4) USB Converters ROHSSilicon LabsUSB ConvertersW25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
README
STM32L433CBT_Developement_Board/README.mdSTM32L433CBTx Development Board

More views



Front Copper
Back Copper
Parts
34| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | C_Small | Capacitor_SMD:C_0805_2012Metric | C1, C2, C3, C4, C5, C6, C8, C9, C10, C11, C12, C13, C14 |
| 3 | R_Small | Resistor_SMD:R_0805_2012Metric | R1, R2, R3 |
| 2 | Conn_01x18_Male | Connector_PinHeader_2.54mm:PinHeader_1x18_P2.54mm_Vertical | J2, J3 |
| 2 | Crystal_GND23_Small | Crystal:Crystal_SMD_Abracon_ABM8G-4Pin_3.2x2.5mm | Y1, Y2 |
| 2 | D_TVS | Diode_SMD:D_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D7, D9 |
| 2 | LED | LED_SMD:LED_0805_2012Metric_Castellated | D10, D12 |
| 2 | USB_B_Micro | Connector_USB:USB_Micro-B_Molex_47346-0001 | J7, USB_to_UART |
| 1 | CP2102N-A01-GQFN24 | Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U2 |
| 1 | Conn_01x04_Male | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Horizontal | SWD |
| 1 | Conn_02x03_Counter_Clockwise | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical_SMD | BOOT |
| 1 | LT1963AxST-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U4 |
| 1 | NeoPixel_THT | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | LED |
| 1 | STM32L433CBTx | Package_QFP:LQFP-48_7x7mm_P0.5mm | STM32L433CBT |
| 1 | SW_DIP_x01 | Button_Switch_SMD:SW_SPST_B3U-1000P-B | RESET |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | W25Q128 |
More from embeddedalpha/PCB-Design
12- 4 layers99.7 × 108 mm

- 4 layers93.6 × 32 mm

- 2 layers30 × 46 mm

- 2 layers40 × 90 mm

- 2 layers34.8 × 30 mm

- 2 layers80 × 50 mm

- 2 layers74.4 × 30 mm

- 2 layers48.3 × 38.1 mm

- 2 layers40 × 25.5 mm

- 2 layers35 × 20 mm

- 2 layers44.5 × 19.7 mm

- 4 layers

Similar boards
- 6 layers230 × 56 mm

- 4 layers100 × 100 mm

ESP32-Eurorack Audio
ctag-fh-kiel/esp32-eurorack-audio
Open source eurorack audio module based on ESP32
173 parts71 - 4 layers160 × 73.2 mm

MainPCB
doppelgrau/esp32-f9p-io-board
An IO-PCB (two motor-driver/H-bridge, CAN, RS232, ADS1115, relay, ethernet, ardusimple f9p compatible connector) with an ESP32 for 12V power, three 15V tolerant analog inputs, three 5V tolerant inputs.
162 parts39 - 4 layers69.8 × 69.8 mm

FreeEEG32
neuroidss/FreeEEG32-alpha1.0
ALPHA1.0 TEST FAILED, USE NEW VERSION INSTEAD FreeEEG32 alpha1.0 32 channels mobile electroencephalography under GNU AGPL 24 bits, 4kSPS ADCs 4x AD7770 MCU STM32F427ZI WIFI ESP-12F (ESP8266) USB CP2102N Accel & hyro…
217 parts39AGPL-3.0 - 2 layers136 × 58 mm

- 2 layers35 × 18 mm

- 2 layers100 × 99.2 mm

Usb serial interface panelized
willemcvu/midi-solenoid-driver
A set of PCBs to drive solenoids using MIDI data, for use in automating musical instruments.
114 parts21MIT - 2 layers65 × 56 mm

Questions
How big is the STM32L433CBT Dev Board PCB?
It measures 30.2 × 50.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the STM32L433CBT Dev Board use?
34 parts, built around the CP2102N-A01-GQFN24 and W25Q128JVSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the STM32L433CBT Dev Board KiCad files?
From the embeddedalpha/PCB-Design repository on GitHub, at the commit this page was made from: the board is STM32L433CBT_Developement_Board/STM32L433CBT_Dev_Board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the STM32L433CBT Dev Board design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).