Skip to the content
2 layers28 × 38 mmADP2303ARDZ, the printed circuit board in 3D

This project is an attempt at an open hardware design Switched Mode Power Supply. It's based on the Analog Devices ADP2302/ADP2303 chips.

Size
28 × 38 mm
Copper layers
2
Thickness
1.6 mm
Parts
17
Nets
9
Pads
48
Tracks, vias
36, 5
Pours
4
Routed
Yes
KiCad
KiCad 5 (file 20171125)
Created
13 Nov 2017
Updated
18 Dec 2017

Overview

ADP2303ARDZ is an open-source printed circuit board by electronicSoup, from the electronicSoup/SMPS-ADP2303ARDZ repository on GitHub. It is a 2-layer board of 28 × 38 mm with 17 parts on 9 nets, routed with 36 tracks and 5 vias.

It is built around the ADP2303ARDZ-5.0 and SSB43L-E3. Its parts include 7 capacitors, 3 resistors, 2 ICs, 2 connectors and 2 inductors.

Main components

2

README

README.md

Synopsis

This project is an attempt at an open hardware design Switched Mode Power Supply. It's based on the Analog Devices ADP2302/ADP2303 chips.

Motivation

Basically for a design I'm working on I needed both a 5V and 3v3 rail. I have previously used another chip but found it very difficult to hand solder, so went looking to replace my current power module. I had hoped to find an Open Hardware design but failed to find such a thing so started this project and documented my naivety in a blog post. This project then is at present more or less a general test board for my proposed supply. I've added Feedback resistors (R2 and R3) into the design but I'm planning to use the fixed 5Volt 3Amp part (ADP2303ARDZ-5.0) so I'll be using a 0 Ohm resistor for R3. In addition as I have, in stock, a Bourns SRN6028 Inductor I've added footprints for both that part and the, datasheet recommended, TDK VLF10040.

This project then is not much different then the Analog Devices but it is not a board but a KiCad Design. I'd hope that I could drag and drop this Supply into my future designs but I somehow doubt that it would be that simple. I sure the schematic could be brought into a new design, which needed a supply, as an additional KiCad sheet, but the layout would probably have to be re-done from scratch. This might not be the case but as I've not gotten to that stage as yet.

The 3v3 rail is from a Microchip MCP1825S fixed 3v3, 500mA LDO regulator. That part is pin compatible with the MCP1826S which is a 1Amp version, so I can easily upgrade the 3v3 Rail to 1Amp. Of course this regulator could also be easily removed from the design, along with it's two Caps. In addition depending on results, output efficiency etc. I may well replace that part of the design with an improved 3v3 rail.

Installation

Because I had to add the parts for ADP2303 and MCP1825 to the KiCad component libraries I've had to used the latest version of KiCad, compiled from source on my machine.

Version Info:

text
Application: kicad
Version: (2017-11-03 revision 08a9dc0)-master, debug build
Libraries:
    wxWidgets 3.0.2
    libcurl/7.47.0 GnuTLS/3.4.10 zlib/1.2.8 libidn/1.32 librtmp/2.3
Platform: Linux 4.4.0-98-generic x86_64, 64 bit, Little endian, wxGTK
Build Info:
    wxWidgets: 3.0.2 (wchar_t,wx containers,compatible with 2.8) GTK+ 2.24
    Boost: 1.58.0
    Curl: 7.47.0
    Compiler: GCC 5.4.0 with C++ ABI 1009

Build settings:
    USE_WX_GRAPHICS_CONTEXT=OFF
    USE_WX_OVERLAY=OFF
    KICAD_SCRIPTING=OFF
    KICAD_SCRIPTING_MODULES=OFF
    KICAD_SCRIPTING_WXPYTHON=OFF
    KICAD_SCRIPTING_ACTION_MENU=OFF
    BUILD_GITHUB_PLUGIN=ON
    KICAD_USE_OCE=OFF
    KICAD_SPICE=OFF

License

CERN OHL version 1.2

First version one input Cap 10uF No Output Cap

Second Version One input Cap 10uF

Parts

17
QtyValueFootprintReferences
20.1uFfootprints:C_0603_1608MetricC6, C7
210uFfootprints:C_0603_1608MetricC1, C2
2Rfootprints:R_0603_1608MetricR2, R3
10,1uFfootprints:C_0603_1608MetricC3
1100kfootprints:R_0603_1608MetricR1
147uFfootprints:C_0805_2012MetricC4
1ADP2303ARDZ-5.0footprints:SOIC-8-1EP_3.9x4.9mm_Pitch1.27mmU1
1Cfootprints:C_0805_2012MetricC5
1Inputfootprints:PinSocket_1x03_P2.54mm_VerticalP1
1MCP1825Sfootprints:SOT-223U2
1Outputfootprints:PinSocket_1x03_P2.54mm_VerticalP2
1SRN6028footprints:L_Bourns-SRN6028L2
1SSB43Lfootprints:D_SMB_HandsolderingD1
1VLF10040Tfootprints:L_TDK_VLF10040L1

Similar boards

  • 4 layers85 × 68 mmFMRC, the printed circuit board in 3D

    FMRC

    svenssonjoel/FMRC

    Four Motor Robot Controller

    107 parts1GPL-3.0
  • 4 layers145 × 73 mmDashboard, the printed circuit board in 3D

    Dashboard

    broncoracing/dashboard

    BR23 Dashboard PCB/Firmware

    284 parts
  • 2 layersEps, the printed circuit board in 3D

    Eps

    TJREVERB/reverb_eps

    Stopgap EPS design for TJREVERB (Not to be used as flight hardware)

    355 parts
  • 2 layers92 × 88 mmBattery Board, the printed circuit board in 3D

    Battery Board

    bluesatunsw/rocketry-datasat

    Cubesat-shaped data collection payload for Rocketry's Griffon rocket

    34 parts2GPL-3.0
  • 4 layers82.4 × 100 mmBcm, the printed circuit board in 3D

    Bcm

    broncoracing/bcm

    Body Control Module

    141 parts
  • 4 layers100 × 60 mmPrecharge, the printed circuit board in 3D

    Precharge

    broncoracing/precharge

    Precharge circuit for BR23-E

    33 parts
  • 4 layers100.5 × 82.8 mmTssi rtml, the printed circuit board in 3D

    Tssi rtml

    broncoracing/tssi-rtml

    BR25e TSSI RTML board

    94 parts

Questions

How big is the ADP2303ARDZ PCB?

It measures 28 × 38 mm and has 2 copper layers, 1.6 mm thick.

What parts does the ADP2303ARDZ use?

17 parts, built around the ADP2303ARDZ-5.0 and SSB43L-E3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ADP2303ARDZ KiCad files?

From the electronicSoup/SMPS-ADP2303ARDZ repository on GitHub, at the commit this page was made from: the board is ADP2303ARDZ.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the ADP2303ARDZ design in my own project?

Its repository states no licence, so its author keeps all rights: ask electronicSoup before reusing the design.