
Sensorstrip power-42-square
eatnooM/sensorstrip
USB-C powered, slim IR emitter for use with Wii / light guns

USB-C powered, slim IR emitter for use with Wii / light guns
Sensorstrip emitter is an open-source printed circuit board by eatnooM, from the eatnooM/sensorstrip repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 2-layer board of 40 × 12.5 mm with 8 parts on 5 nets, routed with 6 tracks and 13 vias.
Its parts include 3 diodes, 2 connectors and 1 resistor.
A small and elegant board that will take 5V from its USB-C board to power its own LEDs and pass it on to any other emitter boards in your setup.
Old picture - there have been some changes since this picture
This board is ideal for the smallest setup possible with no dedicated power board.
| Reference | Part desc / number | Notes |
|---|---|---|
| J1 | 6-pin SMD Type C connector - Mouser / LCSC | |
| J2 | Molex 53261-0271 - Mouser | |
| - | Picoblade Cable assembly - Preassembled - Mouser (60cm length) / LCSC - housing + LCSC - terminal | Need one of these for each emitter board |
| F1 | 0805 PTC - Mouser / LCSC | Overcurrent protection |
| D1-3 | IR LED - 940nm - Mouser | |
| D4 | Status LED - Mouser / LCSC | Optional |
| R1 | 7-120R 0805 - Mouser / LCSC | Value depends on your LEDs - 7-10R work well with SFH-4547 |
| R2,R3 | 5.1K 0603 - Mouser / LCSC | Required if powering from C-C cable |
| R4 | 1K 0603 - Mouser / LCSC | Required for status LED |
| SW1 | DPDT - Mouser / LCSC | Optional, but recommended |
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | LED | sensorstrip:LED_THT-1.27mm-OrthogonalSMDAndTHT | D1, D2, D3 |
| 2 | Conn_01x02_MountingPin | sensorstrip:Molex_Picoblade_53261-0271-Hybrid | J1, J2 |
| 2 | MountingHole-2mm-NPTH | sensorstrip:MountingHole-2mm-NPTH | , |
| 1 | 120R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |

eatnooM/sensorstrip
USB-C powered, slim IR emitter for use with Wii / light guns

eatnooM/sensorstrip
USB-C powered, slim IR emitter for use with Wii / light guns

eatnooM/sensorstrip
USB-C powered, slim IR emitter for use with Wii / light guns

eatnooM/sensorstrip
USB-C powered, slim IR emitter for use with Wii / light guns


joeycastillo/Sensor-Watch
A board replacement for the classic Casio F-91W wristwatch

rusefi/rusefi
rusefi - GPL internal combustion engine control unit

hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

shanteacontrols/OpenDeck
A platform for building interactive control and sensing devices using MIDI and OSC built with Zephyr RTOS.

hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

dangiu/PicoMemcard
Emulating PSX Memory Card (or controller) using a Raspberry Pi Pico

OLIMEX/DIY-LAPTOP
Do It Yourself Open Source Hardware and Software Modular Hacker's Friendly Laptop
It measures 40 × 12.5 mm and has 2 copper layers, 1.6 mm thick.
8 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the eatnooM/sensorstrip repository on GitHub, at the commit this page was made from: the board is sensorstrip-emitter/sensorstrip-emitter.kicad_pcb and its schematic sensorstrip-coupler/sensorstrip-coupler.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).