
Base
google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards

A Valentine's Day LEDs
Heart is an open-source printed circuit board by dybarsky, from the dybarsky/valentines-leds repository on GitHub, published under the MIT licence. It is a 2-layer board of 119.1 × 105.8 mm with 43 parts on 9 nets, routed with 267 tracks and 0 vias.
Its parts include 18 resistors and 3 capacitors.
An Open Source & Open Hardware project.
Demo gif (loads a bit long) 👇

The core of this project is MSP430G2553 mictrocontroller by Texas Instruments and two SN74HC595N 8-bit shift registers. Each 8-bit shift register controls 8 3mm red LEDs. Also resistors, capacitors, slide switch, tacticle button, DIP sockets, Li-ion akku 3.7V, a JST connector.
Check schematics below to get values for resistors and capacitors.
Here are all used components 👇

And this is how assembly looks like 👇

I used KiCad to design hardware. Source files are located in pcb folder.
This is a schematic diagram 👇
KiCad project fies for PCB as well as Gerber files for PCB production are also located in pcb fodler.
This is a PCB design 👇

With highlighted nets 👇

Firmware for this project was written in pure C, operating with IC registers directly (without platformio or any other ports of arduino libraries). It requires some deeper knowledge of MSP430G2553 datasheet and hardware communication protocols, but drastically reduces binary size. It's only 14 KB!
There are 6 different patterns of LEDs blinking. They are store in 2 dimensional arrays of bytes.
Timer intrruptions are configured to be called every 0.1 second. IC goes over array and sends data to 8-bit shift register. Communication between the microcontroller and 8-bit shift registers is done via SPI protocol. When IC is not busy, it goes to low power mode.
https://www.youtube.com/watch?v=liG8lNvPkbY
https://www.instructables.com/Electronic-Heart-Valentines-Day-Gift/
| Qty | Value | Footprint | References |
|---|---|---|---|
| 18 | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2, R3, R4, R5, R6, R7, R10, R11, R12, R13, R14, R15, R16, R17, R18 +2 |
| 16 | LED_D3.0mm | LED_THT:LED_D3.0mm | A1, A2, B1, B2, C1, C2, D1, D2, E1, E2, F1, F2, G1, G2, H1, H2 |
| 3 | CP_Radial_D5.0mm_P2.50mm | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C1, C2, C3 |
| 2 | DIP-16_W7.62mm | Package_DIP:DIP-16_W7.62mm | SN54HC595(1), SN54HC595(2) |
| 1 | DIP-20_W7.62mm | Package_DIP:DIP-20_W7.62mm | MSP430G2553 |
| 1 | PinSocket_1x02_P2.00mm_Vertical | Connector_PinSocket_2.00mm:PinSocket_1x02_P2.00mm_Vertical | BAT |
| 1 | PinSocket_1x03_P2.54mm_Vertical | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | PWR |
| 1 | SW_PUSH_6mm_H5mm | Button_Switch_THT:SW_PUSH_6mm_H5mm | BTN |

google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards

rusefi/rusefi
rusefi - GPL internal combustion engine control unit


jrsteensen/OpenHornet
OpenHornet 1:1 F/A-18C Simulator Repository


tebl/RC6502-Apple-1-Replica
An expandable SBC-version of the Apple 1 computer, easy to get started with and lot of cool stuff that can be added to it!

nodestark/mdb-esp32-cashless
ESP32-based MDB cashless device for vending machines, supporting EVA DTS DEX/DDCMP telemetry and payments over the MDB protocol via Bluetooth and MQTT

zynthian/zynthian-hw
Zynthian hardware stuff: PCBs, schemes, parts specifications, pin assignment, ...
It measures 119.1 × 105.8 mm and has 2 copper layers, 1.6 mm thick.
43 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the dybarsky/valentines-leds repository on GitHub, at the commit this page was made from: the board is pcb/heart.kicad_pcb and its schematic pcb/heart.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).