Skip to the content
2 layers119.1 × 105.8 mmHeart, the printed circuit board in 3D

A Valentine's Day LEDs

Size
119.1 × 105.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
43
Nets
9
Pads
133
Tracks, vias
267, 0
Pours
1
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
5 Feb 2025
Updated
24 Feb 2025

Overview

Heart is an open-source printed circuit board by dybarsky, from the dybarsky/valentines-leds repository on GitHub, published under the MIT licence. It is a 2-layer board of 119.1 × 105.8 mm with 43 parts on 9 nets, routed with 267 tracks and 0 vias.

Its parts include 18 resistors and 3 capacitors.

README

README.md

HEART LEDs Valentine's day gift.

An Open Source & Open Hardware project.

Demo gif (loads a bit long) 👇

Parts

The core of this project is MSP430G2553 mictrocontroller by Texas Instruments and two SN74HC595N 8-bit shift registers. Each 8-bit shift register controls 8 3mm red LEDs. Also resistors, capacitors, slide switch, tacticle button, DIP sockets, Li-ion akku 3.7V, a JST connector.

Check schematics below to get values for resistors and capacitors.

Here are all used components 👇

And this is how assembly looks like 👇

Schematic

I used KiCad to design hardware. Source files are located in pcb folder.
This is a schematic diagram 👇

PCB Design

KiCad project fies for PCB as well as Gerber files for PCB production are also located in pcb fodler.
This is a PCB design 👇

With highlighted nets 👇

Firmware

Firmware for this project was written in pure C, operating with IC registers directly (without platformio or any other ports of arduino libraries). It requires some deeper knowledge of MSP430G2553 datasheet and hardware communication protocols, but drastically reduces binary size. It's only 14 KB!

There are 6 different patterns of LEDs blinking. They are store in 2 dimensional arrays of bytes.
Timer intrruptions are configured to be called every 0.1 second. IC goes over array and sends data to 8-bit shift register. Communication between the microcontroller and 8-bit shift registers is done via SPI protocol. When IC is not busy, it goes to low power mode.

Demo

https://www.youtube.com/watch?v=liG8lNvPkbY

Instrucitons

https://www.instructables.com/Electronic-Heart-Valentines-Day-Gift/

Parts

43
QtyValueFootprintReferences
18R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1, R2, R3, R4, R5, R6, R7, R10, R11, R12, R13, R14, R15, R16, R17, R18 +2
16LED_D3.0mmLED_THT:LED_D3.0mmA1, A2, B1, B2, C1, C2, D1, D2, E1, E2, F1, F2, G1, G2, H1, H2
3CP_Radial_D5.0mm_P2.50mmCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC1, C2, C3
2DIP-16_W7.62mmPackage_DIP:DIP-16_W7.62mmSN54HC595(1), SN54HC595(2)
1DIP-20_W7.62mmPackage_DIP:DIP-20_W7.62mmMSP430G2553
1PinSocket_1x02_P2.00mm_VerticalConnector_PinSocket_2.00mm:PinSocket_1x02_P2.00mm_VerticalBAT
1PinSocket_1x03_P2.54mm_VerticalConnector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_VerticalPWR
1SW_PUSH_6mm_H5mmButton_Switch_THT:SW_PUSH_6mm_H5mmBTN

Similar boards

  • 2 layers52.2 × 52.2 mmBase, the printed circuit board in 3D

    Base

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    43 parts3kApache-2.0
  • 2 layers33 × 34 mmESP32-bat monitor latch, the printed circuit board in 3D

    ESP32-bat monitor latch

    pcbreflux/espressif

    all espressif stuff will committed here

    43 parts608GPL-3.0
  • 2 layers42.9 × 19 mmPoly kb 2.25U, the printed circuit board in 3D

    Poly kb 2.25U

    thpoll83/PolyKybd

    PolyKybd

    43 parts411CERN-OHL-W-2.0
  • 2 layers99.1 × 99.7 mmRC6502 Prototyping, the printed circuit board in 3D

    RC6502 Prototyping

    tebl/RC6502-Apple-1-Replica

    An expandable SBC-version of the Apple 1 computer, easy to get started with and lot of cool stuff that can be added to it!

    43 parts193GPL-3.0
  • 2 layers26.6 × 38.7 mmMdb slave esp32s3-mini, the printed circuit board in 3D

    Mdb slave esp32s3-mini

    nodestark/mdb-esp32-cashless

    ESP32-based MDB cashless device for vending machines, supporting EVA DTS DEX/DDCMP telemetry and payments over the MDB protocol via Bluetooth and MQTT

    43 parts190MIT
  • 2 layers97.3 × 71 mmZynScreen v1, the printed circuit board in 3D

    ZynScreen v1

    zynthian/zynthian-hw

    Zynthian hardware stuff: PCBs, schemes, parts specifications, pin assignment, ...

    43 parts156

Questions

How big is the Heart PCB?

It measures 119.1 × 105.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Heart use?

43 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Heart KiCad files?

From the dybarsky/valentines-leds repository on GitHub, at the commit this page was made from: the board is pcb/heart.kicad_pcb and its schematic pcb/heart.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Heart design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).