

Chrononauts board
This sub-folder contains the hardware design files for an RF transceiver system built using an ESP32-C3 module and a CC1101 RF chip.
- Size
- 54.1 × 33.9 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 59
- Nets
- 62
- Pads
- 207
- Tracks, vias
- 482, 97
- Pours
- 12
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 31 May 2024
- Updated
- 28 Apr 2026
Overview
Chrononauts board is an open-source printed circuit board by dsg-jam, from the dsg-jam/chrononauts-quest repository on GitHub, published under the MIT licence. It is a 2-layer board of 54.1 × 33.9 mm with 59 parts on 62 nets, routed with 482 tracks and 97 vias.
It is built around the CC1101RGP, ESP32-C3-WROOM-02-N4 and TLV62568DBVR-TP, with the MXC6655XA, CPDQ5V0-HF and 155060VS73200 among its other parts. Its parts include 23 capacitors, 13 resistors, 6 diodes, 5 inductors and 4 ICs. It belongs with the ESP32 and RISC-V boards of this library.
Main components
10CC1101RGP
QFN-20-EP(4x4)-116dBm -40℃~+85℃ 1.8V~3.6V 12.3mA 12dBm 14.3mA 600Kbps ISM SPI QFN-20-EP(4x4) RF Transceiver ICs ROHSTexas InstrumentsRF Transceiver ICsESP32-C3-WROOM-02-N4
SMD,20x18mm-105dBm -40℃~+85℃ 2.4GHz 20.5dBm 345mA 3V~3.6V 82mA Bluetooth5.0 ESP32-C3 Chip Integrated Bluetooth function、Support USB interface On-board PCB Antenna UART、SPI、I2C、I2S、JTAG、USB SMD,20x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesTLV62568DBVR-TP
SOT-23-5-40℃~+85℃ 1 1.5A 1.5MHz 2.5V~6V 40uA Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Cable compensation Step-down type Yes SOT-23-5 DC-DC Converters ROHSTECH PUBLICDC-DC ConvertersMXC6655XA
LGA-12(2x2)-40℃~+85℃ 1.62V~3.6V 12bit 1uA Accelerometer I2C Motion event detection X,Y,Z ±8g LGA-12(2x2) Accelerometers ROHSMEMSICAccelerometersCPDQ5V0-HF
0402(SOD-923F)-40℃~+125℃ 1 15pF 174W@8/20us 18.6V 1uA 5.6V 5V 9.4A@8/20us ESD IEC 61000-4-2 0402(SOD-923F) ESD and Surge Protection (TVS/ESD) ROHSComchipESD And Surge Protection (TVS/ESD)155060VS73200
SMD,1.6x1.0mm-40℃~+85℃ 120° 20mA 2V 48mW 573nm 575nm 70mcd Discrete Diode Water Clear Yellow Green SMD,1.6x1.0mm LED Indication - Discrete ROHSWürth ElektronikLED Indication - DiscreteB5819W-TP
SOD-123-65℃~+125℃ 1 Independent 10A 1A 1mA@40V 40V 600mV@1A SOD-123 Schottky Diodes ROHSMicro Commercial ComponentsSchottky DiodesNX3225GA-26MHZ-TI
SMD3225-4P-40℃~+85℃ 10pF 26MHz 50Ω ±20ppm ±40ppm SMD3225-4P Crystals ROHSNDKCrystalsPVG3A103C01R00
SMD-3P,3.6x3.4mm1 10kΩ 250mW ±150ppm/℃ ±20% SMD-3P,3.6x3.4mm Potentiometers, Variable Resistors ROHSBournsPotentiometers & Variable ResistorsUSB4105-GF-A
SMD-40℃~+85℃ 1 12P 48V 5A Black Female Surface Mount, Right Angle Type-C USB 2.0 SMD USB Connectors ROHSGlobal Connector Technology (GCT)USB Connectors
README
board/hw/README.mdHW
This sub-folder contains the hardware design files for an RF transceiver system built using an ESP32-C3 module and a CC1101 RF chip. The communication between the ESP32-C3 and CC1101 is established through the Serial Peripheral Interface (SPI) protocol. The design is created using KiCad 8.
Abstract
The project aims to create a versatile RF communication system by integrating the ESP32-C3 module and the CC1101 RF chip. The ESP32-C3 serves as the main controller, handling data processing and interfacing with external devices, while the CC1101 handles the RF communication with other compatible devices. This design allows for bi-directional communication over a designated RF frequency band, making it suitable for various applications such as replacing remote controls.
Note: The design around the CC1101 chip is tuned for the 315/433 MHz ISM/SRD frequency bands. (See the documentation of the CC1101 chip for more information.)
Opening the Design
Follow these steps to open the hardware design using KiCad 8:
-
Clone this repository to your local machine and change into this directory.
-
Launch KiCad 8.
-
Open the KiCad project by navigating to the project directory and locating the
chrononauts-board.kicad_profile. This file stores the project information. -
Once the project is open, you can access the schematic and PCB layout files by clicking on the respective buttons in the KiCad project manager.
-
Adjust the design and/or export the gerbel files for PCB production
Design Files
The repository contains the following design files:
- Schematic files (
.kicad_sch) - These files define the circuit connections and component values. - PCB layout files (
.kicad_pcb) - These files represent the physical arrangement of components on the PCB. - Component libraries (see the
PCBLibsubmodule) - Custom libraries that include footprints and symbols for the ESP32-C3, CC1101, and other components used in the design.
Parts
59| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 220pF | PCBLib:Cap_Murata_GRM_0402 | C5, C6, C11, C12, C13 |
| 3 | 100nF | PCBLib:Cap_Murata_GRM_0402 | C1, C10, C16 |
| 3 | 10k | PCBLib:R_Vishay_CRCW_0402 | R2, R3, R8 |
| 3 | 10uF | PCBLib:Cap_Murata_GRM_0402 | C17, C20, C21 |
| 3 | 174 | PCBLib:R_Vishay_CRCW_0402 | R9, R10, R11 |
| 3 | 27nH | PCBLib:L_Murata_LQG_0402 | L1, L3, L4 |
| 3 | CPDQ5V0-HF | PCBLib:SODFL1006X40N | D1, D2, D3 |
| 3 | MountingHole_Pad | MountingHole:MountingHole_2.2mm_M2_DIN965_Pad_TopBottom | H1, H2, H4 |
| 2 | 10nF | PCBLib:Cap_Murata_GRM_0402 | C14, C15 |
| 2 | 155060VS73200 | PCBLib:155060VS73200 | LED1, LED2 |
| 2 | 1uF | PCBLib:Cap_Murata_GRM_0402 | C18, C23 |
| 2 | 27pF | PCBLib:Cap_Murata_GRM_0402 | C2, C3 |
| 2 | 2K7 | PCBLib:R_Vishay_CRCW_0402 | R13, R14 |
| 2 | 3.9pF | PCBLib:Cap_Murata_GRM_0402 | C4, C7 |
| 2 | 5k1 | PCBLib:R_Vishay_CRCW_0402 | R4, R5 |
| 1 | 2-1977223-8 | PCBLib:219772238 | S3 |
| 1 | 2.2uH | PCBLib:ASPI0418FS | L5 |
| 1 | 22nH | PCBLib:L_Murata_LQG_0402 | L2 |
| 1 | 4.7uF | PCBLib:Cap_Murata_GRM_0603 | C22 |
| 1 | 442k | PCBLib:R_Bourns_CR_0603 | R6 |
| 1 | 5.6pF | PCBLib:Cap_Murata_GRM_0402 | C9 |
| 1 | 56k | PCBLib:R_KOA_RK_0402 | R1 |
| 1 | 6.8pF | PCBLib:Cap_Murata_GRM_0402 | C19 |
| 1 | 73251-1290 | PCBLib:Molex-SD-73251-129 | J1 |
| 1 | 8.2pF | PCBLib:Cap_Murata_GRM_0402 | C8 |
| 1 | 97.6k | PCBLib:R_Bourns_CR_0603 | R7 |
| 1 | B5819W-TP | PCBLib:SOD3716X135N | D4 |
| 1 | CC1101RGP | PCBLib:CC1101RGP | U1 |
| 1 | ESP32-C3-WROOM-02-N4 | PCBLib:ESP32C3WROOM02N4 | IC1 |
| 1 | MXC6655XA | PCBLib:MXC6655XA | IC3 |
| 1 | NX3225GA-26MHZ | PCBLib:NX3225GA16000MSTDCRG1 | Y1 |
| 1 | PVG3A103C01R00 | PCBLib:PVG3A103C01R00 | VR1 |
| 1 | TLV62568DBVR | PCBLib:TLV62568DBVR | IC2 |
| 1 | USB4105-GF-A | PCBLib:GCT_USB4105-GF-A | J2 |
Similar boards
- 2 layers54.1 × 21.9 mm

- 2 layers35 × 55 mm

- 4 layers93.9 × 97.3 mm

CubeSat Comms XCVR PCB Fall2025-Version
jonnylin22/CubeSat-Communications-Board-Fall-2025-V2
Features pinout connector to external MCU RX and TX status LEDs Organized BOM
68 parts - 2 layers38.6 × 17.1 mm

- 4 layers242.1 × 170 mm

Night light PCB
oyeniyihakeem08-blip/Night-light-PCB-prototype
A smart, motion-sensing LED night light that runs straight from the mains, keeps working through power cuts on its own battery, and is controlled by a paired wireless remote.
155 parts - 2 layers71.8 × 62.2 mm

Air quality pcb v7
NilsEngelbach/air-quality-pcb
Seventh iteration: ESP8266 → ESP32-C3 (native USB, no UART bridge), fixes from the v6 design review, right-angle switches with longer actuators, a STEMMA QT port for optional sensors, and charge-status sensing.
85 parts - 2 layers43.3 × 37.6 mm

ZBSmartMeter
Tropaion/ZigBee_SmartMeter_Reader
This is a ZigBee device to collect data from smartmeters using the DLMS/COSEM protocol.
37 parts32GPL-3.0 - 6 layers67 × 74.5 mm

Motherboard2.0
Jack-Cb/Team-Jaxis-3-Axis-Coil
Documentation, resources, code, schematics, pcb layouts, and all related materials for the 3-Axis Coil ECE project at Oregon State University.
44 parts
Questions
How big is the Chrononauts board PCB?
It measures 54.1 × 33.9 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Chrononauts board use?
59 parts, built around the CC1101RGP, ESP32-C3-WROOM-02-N4, TLV62568DBVR-TP and MXC6655XA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Chrononauts board KiCad files?
From the dsg-jam/chrononauts-quest repository on GitHub, at the commit this page was made from: the board is board/hw/chrononauts-board.kicad_pcb and its schematic board/hw/chrononauts-board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Chrononauts board design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).