
Forcegauge
szbeni/forcegauge
Traning for climbing. Load cell with HX711 and real time plotting,

Source code for my c64-wifimodem
C64-wifimodem is an open-source printed circuit board by DrZingo, from the DrZingo/c64-wifimodem repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 47 × 37.5 mm with 27 parts on 39 nets, routed with 356 tracks and 34 vias.
It is built around the ESP-12E, LM1117-3.3 and BSS138. Its parts include 12 resistors, 5 transistors, 5 connectors, 3 ICs and 1 capacitor. It belongs with the radio and wireless boards and the ESP8266 boards of this library.

Source code for my c64-wifimodem
Feel free to make changes and correction.
PCB files in kicad format. Nothing much to say about it.


C1 Tantalum 22uF Case B, 3528
J4 User Port edge connector
Q1-Q5 BSS138 SOT-23
R1-R12 10k 0805
U1 LM1117-3.3 SOT-223
U2 ESP8266 12E or 12F
U3 OLED 0.96" GND,VCC,SCL,SDA| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 10k | Resistors_SMD:R_0805_HandSoldering | R1, R2, R3, R4, R5, R6, R7, R8, R9, R10, R11, R12 |
| 5 | BSS138 | TO_SOT_Packages_SMD:SOT-23_Handsoldering | Q1, Q2, Q3, Q4, Q5 |
| 3 | GS2 | Connectors:GS2 | J1, J2, J3 |
| 1 | 22µ | Capacitors_Tantalum_SMD:CP_Tantalum_Case-B_EIA-3528-21_Hand | C1 |
| 1 | CONN_01X04_MALE | Pin_Headers:Pin_Header_Straight_1x04_Pitch2.54mm | J5 |
| 1 | ESP-12E | ESP8266:ESP-12E_SMD_wo_line | U2 |
| 1 | Jumper_NO_Small | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm | JP1 |
| 1 | LM1117-3.3 | TO_SOT_Packages_SMD:SOT-223 | U1 |
| 1 | USERPORT | C64-Userport:USERPORT | J4 |
| 1 | small_i2c_oled_v2 | OLED:Small_I2C_OLED_v2 | U3 |

szbeni/forcegauge
Traning for climbing. Load cell with HX711 and real time plotting,

dm2lct/tlnixie
PCB files for the Turmlabor nixie clock 2.0

dm2lct/Nixieclock_kit
This is a Nixie-clock controlled by a ESP8266 module with NTP and MQTT support.


UtilitechAS/amsreader-firmware
ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported



It measures 47 × 37.5 mm and has 2 copper layers, 1.6 mm thick.
27 parts, built around the ESP-12E, LM1117-3.3 and BSS138. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the DrZingo/c64-wifimodem repository on GitHub, at the commit this page was made from: the board is C64-wifimodem/C64-wifimodem.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).