Skip to the content
2 layers232.4 × 84.7 mmMint36tt rev02, the printed circuit board in 3D

Mint36tt rev02

DrMint/mint36tt2

A split keyboard

Size
232.4 × 84.7 mm
Copper layers
2
Thickness
1.6 mm
Parts
82
Nets
38
Pads
430
Tracks, vias
475, 53
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
30 Dec 2024
Updated
3 Feb 2025

Overview

Mint36tt rev02 is an open-source printed circuit board by DrMint, from the DrMint/mint36tt repository on GitHub. It is a 2-layer board of 232.4 × 84.7 mm with 82 parts on 38 nets, routed with 475 tracks and 53 vias.

It belongs with the keyboards and input boards of this library.

README

README.md

Mint36tt (provisional name)

Design goals

  1. Ergonomic

    • Split
    • Reduced number of keys
    • Reduced key spacing
    • Splay
  2. On-the-go

    • Low profile
    • Silent
    • Small footprint
    • key protection
    • Light
    • USB-C
  3. Sourceable

    • Open source hardware
    • 3D printable (FDM)
    • Common components
    • Hot swappable board and switches
    • Reasonably cheap

The two halves combines together using magnets to transform into its own carry case. This prevent damage to the keys during transport and protect the keyboard from dust.

Physical sizes for one half:

Width: 118.5mm
Height: 90.5mm
Thickness: 14.8mm Weight: 110g (wired version)

Switches

Kailh Choc switches are the thinnest at 11mm (ref. https://www.reddit.com/r/MechanicalKeyboards/comments/165c11v/the_biggest_issue_with_lowprofile_switches_they/).

There are thinner switches such as the Kailh Notebook X (6.5mm) or the Cherry MX Ultra low-profile (3.5mm). But these are more expensive and don't have much variety.

Choosen switches: Kailh Choc Ambient Silent

Key caps

Chocs standard keycaps are 16.5mm × 17.5mm. I decided to go with 16.5mm × 16.5mm CBX keycaps from Chosfox, which results in a 17.5mm spacing (a ~15% area reduction compared to MX's 19mm spacing).

It's possible to buy 15mm keycaps for a 16mm spacing (~30% area reduction). That would be the smallest possible spacing when paired with Chocs as 15mm is already the size of the switches.

It's also possible to reduce the gap beween keys. The standard is 1mm, but it could possibly be reduced to 0.5mm if the switches have little to no wobble and the tolerances on other parts are top notch.

Choosen caps: CFX caps

Microcontroller

Choosen microcontroller: Seeed Studio XIAO RP2040 or Seeed Studio XIAO nRF52840 for wireless.

Shopping list

Common for either version

  • Left and right PCBs
  • 4 × 7 pin headers
  • 36 × 1N4148W SOD123 diodes
  • 36 × Chocfox CFX caps, including:
    • 30 × 1U Chocfox CFX caps
    • 2 × 1.25U Chocfox CFX caps
    • 4 × 1.5U Chocfox CFX caps
  • 36 × Kailh Choc switches
  • 36 × Kailh Choc Hot Swap Sockets
  • 1 × USB-C cable

Specific for the wireless version

  • 2 × Seeed Studio XIAO nRF52840
  • 2 × 601818 LiPo 3.7V 170mAh (18mm × 20mm × 6mm)
  • 2 × MSK12C02 on/off slide switch

Specific for the wired version

  • 2 × Seeed Studio XIAO RP2040
  • 1 × TRRS cable
  • 2 × TRRS jacks PCB mount (MJ-4PP-9 or PJ320A)

With the case (recommended):

  • Left and right upper cases
  • Left and right lower cases
  • Left and right plates (optional)
  • 8 × N52 neodymium magnet (cylinder-shaped, Ø 5mm × 5mm) (recommended)
  • 20 × M2 countersunk screws (Ø 2mm × 5mm)
  • 10 × M2 standoffs (Ø 2mm × 9mm)

Parts

82
QtyValueFootprintReferences
36PG1350, , , , , , , , , , , , , , , +20
36SOD-123, , , , , , , , , , , , , , , +20
2MJ-4PP-9_1side,
2601818,
2JSP-2pin,
2MSK12C02,
2XIAO-nRF52840,

More from DrMint/mint36tt

1
  • 2 layers112.7 × 84.7 mmMint36tt rev02 R, the printed circuit board in 3D

    Mint36tt rev02 R

    DrMint/mint36tt

    A split keyboard

    41 parts2

Similar boards

  • 2 layers68 × 55.4 mmESP32-adapter, the printed circuit board in 3D

    ESP32-adapter

    pcbreflux/espressif

    all espressif stuff will committed here

    82 parts608GPL-3.0
  • 2 layers271.8 × 78.7 mmPCPI AppliCard, the printed circuit board in 3D

    PCPI AppliCard

    baldengineer/bit-preserve

    Project for capturing vintage, classic, aka old computer schematics in KiCad.

    82 parts446
  • 2 layers57.2 × 60.3 mmSmartSpin2k, the printed circuit board in 3D

    SmartSpin2k

    doudar/SmartSpin2k

    Transform your spin bike into a Smart Trainer!

    82 parts292GPL-2.0
  • 2 layers35.6 × 33 mmAxp209 breakout, the printed circuit board in 3D

    Axp209 breakout

    CRImier/MyKiCad

    My KiCad boards. Can't be bothered uploading individually anymore, so here you go.

    82 parts253GPL-3.0
  • 2 layers65 × 40 mmMdb slave esp32s3-sim7080g, the printed circuit board in 3D

    Mdb slave esp32s3-sim7080g

    nodestark/mdb-esp32-cashless

    ESP32-based MDB cashless device for vending machines, supporting EVA DTS DEX/DDCMP telemetry and payments over the MDB protocol via Bluetooth and MQTT

    82 parts190MIT
  • 2 layers83.5 × 66 mmOpen ed Rev.B, the printed circuit board in 3D

    Open ed Rev.B

    krikzz/open-ed

    Open-ED is a very simple and cheap open source Genesis/Megadrive cartridge. The cartridge does not have its own processor or FPGA, it is built in the old school style using only memory and discrete logic.

    82 parts169MIT
  • 2 layers46.3 × 90.7 mmMsiSDR, the printed circuit board in 3D

    MsiSDR

    11tools/msiSDR

    A SDR PCB project base on msi2500 and msi001

    82 parts168GPL-3.0
  • 2 layers97.1 × 97 mmADX, the printed circuit board in 3D

    ADX

    WB2CBA/ADX

    ADX - Arduino Digital Modes HF Transceiver

    82 parts136

Questions

How big is the Mint36tt rev02 PCB?

It measures 232.4 × 84.7 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Mint36tt rev02 use?

82 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Mint36tt rev02 KiCad files?

From the DrMint/mint36tt repository on GitHub, at the commit this page was made from: the board is PCB/kicad/mint36tt_rev02.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Mint36tt rev02 design in my own project?

Its repository states no licence, so its author keeps all rights: ask DrMint before reusing the design.