Skip to the content
2 layers100 × 86.5 mmKinBP, the printed circuit board in 3D

Drop-in replacement controller for Kinesis Contoured keyboards

Size
100 × 86.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
30
Nets
80
Pads
224
Tracks, vias
605, 104
Pours
7
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
10 Mar 2023
Updated
19 Dec 2023

Overview

KinBP is an open-source printed circuit board by DmNosachev, from the DmNosachev/kinbp repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 2-layer board of 100 × 86.5 mm with 30 parts on 80 nets, routed with 605 tracks and 104 vias.

Its parts include 13 connectors, 8 resistors, 4 diodes and 1 IC. It belongs with the STM32 boards of this library.

README

README.md

KinBP

KinBP is a drop-in replacement controller for Kinesis Contoured keyboards.

It serves the same purpose as KinT controller created by Michael Stapelberg.

KinBP v1.2

Features and advantages

  • Controller with QMK firmware support.
  • Uses inexpensive WeAct Studio STM32F401/STM32F411 MCU board. The cost of manufacturing 5 sets is about 12 USD per controller. The PCB has dimensions less than 100×100 mm. Many manufacturers provide additional discounts for smaller boards.
  • Compatible with all Kinesis Contoured keyboards but the earliest models (100/110/120).
  • Additional pads for connecting up to 8 swithes (i.e. additional switches on the keyboard or foot pedals).
  • Replacement thumb cluster PCBs with reversible design. They may be needed for some of 13x models (see below).
  • Thumb cluster switch mounting plates.

Changelog

1.21

  • added 7-pin 1.25mm connector footprints (micro JST) for custom thumb cluster PCBs
  • added spare footprints upside down for connectors with pins on the other sideю

BOM

Connectors

The choice of connectors depends on the keyboard model:

  • KB600 (Advantage2).
  1. 6x 13-pin FPC connectors. Molex 39-53-2135. Please note that the cheap (5 USD for 20 pcs) connectors from Aliexpress are polarised and can only be used for the top row connectors on the KB600; using them in the other positions will not work because the pads on the FPC cable are on the wrong side and the cables are too short to be twisted.
  • KB500 (Advantage).
  1. Connecting keywells and top rows: 4x 13-pin FPC connectors, same as mentioned above.
  2. Connecting thumb cluster PCBs: 2x 10-pin angled 2.54mm headers.
  • KB13x (Essential, Classic, Professional).
  1. Connecting keywell PCBs: 2x angled 13-pin FPC connectors.
  2. Connecting top rows: same angled connectors or straight (same as for KB500/KB600).
  3. Some models had LEDs on the thumb cluster PCBs instead of the controller PCB. In this case you will need a pair of new thum cluster PCBs, optional switch mounting plates (see below) and set of cables/connectors with 1.25mm pitch: 2x 7 pin micro JST 10cm cables + 4x 7 pin micro JST angled connector.

Example of incompatible stock thumb cluster PCBc (Kinesis Professional KB134PC): KB134PC controller

You can also reuse connectors from an stock controller, but desoldering them can be tricky. Please note that the Chinese aliexpress connectors and some of the older connectors only had contacts on one side. For the top rows, you need to position the connector so that the contacts are on the outside (there are two footprints for this): top row connector

Controller PCB (/controller-pcb).

  • WeAct Studio STM32F401 or STM32F411 board. You can buy them for about 6 USD at the official Aliexpress store. Beware of pirated copies! KinBP v1.21
  • 4 pcs 3-mm LEDs
  • 4 pcs 0805 or through-hole resistors. Their value depends on the type of LEDs (I use 1.5k Ohm for orange LEDs).
  • Pair of USB Type C male and female connectors.

Thumb cluster (/thumb-pcb)

  • The design is reversible. So, a minimal batch of 5 PCBs will give you 2 pairs + 1 spare. Thumb PCB Thumb PCB
  • 12x SOD-123 1N4148 diodes.
  • Optional switch mounting plates
  • set of connectors and cables (see above)

Switches

  • Optional: 68 pcs Cherry MX compatible switches.

Buid guide

  1. Test your keyboard. Identify faulty switches. Decide if you like the switches (most of the time there will Cherry Browns) and the top row rubber buttons. If rubber buttons are unacceptable to you and you do not mind spending a lot of time on hand-wiring, then it is worth considering an alternative project — (Kin80)[https://github.com/DmNosachev/kin80].
  2. Disassemble the keyboard. Remove all screws and remove all PCBs. If some of the rubber buttons don't work well, the top row assembly can be taken apart and repaired by sticking pieces of copper tape on the button bottoms. Use hot-melt adhesive to asseble it back.
  3. Assemble the controller PCB.
  4. Optional: assemble thumb cluster PCBs.
  5. Case. Seal the holes on the back of the case with pieces of plastic. Glue the USB connector to the back of the case. Optional: use bitumen sound deadening pads to improve acoustics.
  6. Setup the QMK.
  7. Flash the firmware: qmk flash -kb kinbp -km default. Hold 'boot0' button on MCU board, press 'reset', then release 'boot0' to enter bootloader.

TODO

  • FR4 mounting plate for the thumb cluster.
  • Create universal or separate PCB with RP2040 support.

Parts

30
QtyValueFootprintReferences
41kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR1, R2, R3, R4
41kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR5, R6, R7, R8
43mmLED_THT:LED_D3.0mmLED1, LED2, LED3, LED4
2LEFT_TOPfootprints:39-53-2135J1, J2
2RIGHT_TOPfootprints:39-53-2135J3, J4
1Conn_02x08_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x08_P2.54mm_VerticalJ9
1LEFT_KEYWELLfootprints:39-53-2135J6
1LEFT_THUMBConnector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_VerticalJ7
1LEFT_THUMBfootprints:39-53-2135J10
1LEFT_THUMBConnector_Molex:Molex_PicoBlade_53048-0710_1x07_P1.25mm_HorizontalJ13
1LOGOlogo:qmk-smallG***
1LOGOlogo:q64logoG1
1RIGHT_KEYWELLfootprints:39-53-2135J5
1RIGHT_THUMBConnector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_VerticalJ8
1RIGHT_THUMBConnector_Molex:Molex_PicoBlade_53048-0710_1x07_P1.25mm_HorizontalJ12
1RIGHT_THUMBfootprints:39-53-2135J11
1mounting padMountingHole:MountingHole_6mmH2
1mounting padMountingHole:MountingHole_4.3mm_M4_PadH1
1weact_STM32F4x1footprints:STM32F4x1_MiniF4U1

More from DmNosachev/kinbp

1
  • 2 layers69.2 × 85.9 mmKinbp thumb pcb, the printed circuit board in 3D

    Kinbp thumb pcb

    DmNosachev/kinbp

    Drop-in replacement controller for Kinesis Contoured keyboards

    31 parts15CC-BY-SA-4.0

Similar boards

  • 2 layers52.2 × 52.2 mmBase promicro, the printed circuit board in 3D

    Base promicro

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    30 parts3kApache-2.0
  • 2 layers40.6 × 15.2 mmVr mmm, the printed circuit board in 3D

    Vr mmm

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    30 parts1.2k
  • 2 layers270 × 11 mmDaylight, the printed circuit board in 3D

    Daylight

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    30 parts1.1kGPL-3.0
  • 2 layers65 × 30 mmRgb to hdmi, the printed circuit board in 3D

    Rgb to hdmi

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    30 parts1kGPL-3.0
  • 2 layers40.5 × 58 mmInitial v, the printed circuit board in 3D

    Initial v

    tenderlove/initial-v

    It's a BMW shifter converted to a Bluetooth Keyboard that you use with Vim

    30 parts1kApache-2.0
  • 2 layers34.3 × 41.8 mmMotionCubeViewAllForces, the printed circuit board in 3D

    MotionCubeViewAllForces

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    30 parts915
  • 2 layers57.4 × 62 mmPicoWS2812, the printed circuit board in 3D

    PicoWS2812

    ErichStyger/mcuoneclipse

    McuOnEclipse projects and examples

    30 parts765
  • 2 layers52.1 × 46.8 mmFIRE TEST PANEL, the printed circuit board in 3D

    FIRE TEST PANEL

    jrsteensen/OpenHornet

    OpenHornet 1:1 F/A-18C Simulator Repository

    30 parts431

Questions

How big is the KinBP PCB?

It measures 100 × 86.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the KinBP use?

30 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the KinBP KiCad files?

From the DmNosachev/kinbp repository on GitHub, at the commit this page was made from: the board is controller-pcb/kinBP.kicad_pcb and its schematic controller-pcb/kinBP.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the KinBP design in my own project?

Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).