Skip to the content
2 layers92 × 69 mmKin80, the printed circuit board in 3D

Replacement PCB for Kinesis Contoured keyboards

Size
92 × 69 mm
Copper layers
2
Thickness
1.6 mm
Parts
25
Nets
46
Pads
136
Tracks, vias
377, 109
Pours
5
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
15 Mar 2022
Updated
10 Mar 2023

Overview

Kin80 is an open-source printed circuit board by DmNosachev, from the DmNosachev/kin80 repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 2-layer board of 92 × 69 mm with 25 parts on 46 nets, routed with 377 tracks and 109 vias.

Its parts include 8 resistors, 8 connectors, 4 diodes and 1 IC. It belongs with the keyboards and input boards and the STM32 boards of this library.

README

README.md

Kin80

Kin80 is a set of replacement PCBs and switch mounting plates for Kinesis Contoured keyboards.

White Kin80 controller

It is not a drop-in replacement controllers like Stapelberg or KinT (for these controllers I developed a cheap alternative called kinBP (will be published soon)). Kin80 uses different matrix (12×7) and it is aimed at serious modding of the Kinesis keyboard.

Features

Controller PCB

Uses inexpensive WeAct Studio STM32F401/STM32F411 MCU board.

The PCB has dimensions less than 100×100 mm. Many manufacturers provide additional discounts for smaller boards.

Additional pads for connecting up to 4 swithes (i.e. additional switches on the keyboard or foot pedals) and 5 free MCU pins.

  • Eliminating one of the main drawbacks of Kinesis keyboards (prior to Advantage 2): rubber top row is replaced by with mechanical switches, MX or Kailh Choc. Top PCB
  • Replacement thumb cluster PCBs. Reversible design, additional mounting holes for compatibility with Model 110. Thumb PCB
  • Thumb cluster switch mounting plates.

Disadvantages / shortcomings

  1. It's obviously more labour intensive than drop-in controller replacement. You have to desolder the key-wells and than carry out hand-wiring of new (or stock) switches. I started designing a PCB for key-wells, but came to the conclusion that flexible boards of this size are too expensive to manufacture.

  2. It's necessary to carefully cut out two windows in the keyboard case with Dremel, then glue the mounting plates there. The result will most likely not look very professional. This problem can be solved by 3D printing curved plastic plates, but I don't have the skills to design them.

  3. Thumb cluster PCBs require SMD diodes (SOD-323). Soldering them by hand can be tricky for unexperienced people. I'm going to add support for through-hole diodes in the next release.

  4. Top row PCB have not been tested yet.

  5. Other TODO's: design universal MX/Choc top row PCB, design FR4 mounting plate for the thumb cluster.

BOM

  1. Controller PCB (/controller-pcb).
  • WeAct Studio STM32F401 or STM32F411 board. You can buy them for about 6 USD at the official Aliexpress store. Beware of pirated copies!
  • 2 pcs: 20 cm cable with 11-pin female Micro JST connectors with 1.25 mm pitch (Aliexpress) for key-wells
  • 2 pcs: 10 cm cable with 7-pin female Micro JST connectors for connecting thumb clusters
  • 2 pcs: cable with 7-pin female Micro JST connectors for connecting top row clusters, 10 cm if using PCBs or 20 cm if using hand-wiring.
  • 2 pcs male Micro JST 11-pin angled or straight connectors
  • 4 pcs male Micro JST 7-pin angled or straight connectors
  • 4 pcs 3-mm LEDs
  • 4 pcs 0805 or through-hole resistors. Their value depends on the type of LEDs (I use 1.5k Ohm for orange LEDs).
  • Pair of USB Type C male and female connectors
  1. Thumb cluster (/thumb-pcb)
  • The design is reversible. So, a minimal batch of 5 PCBs will give you 2 pairs + 1 spare.
  • 12 pcs SOD-323 1N4148 diodes.
  • Optional: mounting plates (see /plates/thumb).
  • 2 pcs male Micro JST 7-pin angled connectors
  1. Top row cluster (/top-pcb)
  • The PCBs are not tested yet. They also have reversible design.
  • 12 pcs SOD-323 1N4148 diodes.
  • PCBs are optional, you can use just plates (/plates/top) and make a hand-wiring with through-hole diodes.
  1. Key-wells
  • 56 pcs 1N4148 diodes
  • Wire
  1. ** Switches **
  • 80 pcs Cherry MX compatible switches or 68 pcs MX + 12 pcs Kailh Choc
  • Optional: switch opener (if you reuse the stock switches)

Buid guide

  1. Disassemble the keyboard. Remove all screws and remove all PCBs. Сut the melted pins on the back plates of the top clusters.
  2. Desolder the key-well PCBs. If you do not plan to use these PCBs to repair other keyboards, then you can not worry about damaging them.
  3. If you plan to reuse the stock switches, then remove the diodes from them (IMHO, it will make further hand-wiring easier). Desolder the switches from thumb cluster PCBs.

You may notice that swiches are glued with hot-melt adhesive. To remove it, just wipe it with isopropyl alcohol. It will not dissolve the glue, but make it lose its adhesive properties.

  1. Hand-wire the key-wells. You need ROW2COL direction, i.e. the anode of each diode must be connected to a switch pin, cathode (marked by black strip) — to row. See Modern handwiring guide. Kin80 assembled
  2. Assemble thumb cluster PCBs.
  3. Assemble top row PCBs or use hand-wiring.
  4. Assemble the controller PCB. Controller
  5. Case. Cut two windows for new top row keys. You can use hot-melt adhesive to glue the plates to the case. Seal the holes on the back of the case with pieces of plastic. Glue the USB connector to the back of the case. Optional: use bitumen sound deadening pads to improve acoustics. USB
  6. Setup the QMK.
  7. Flash the firmware: qmk flash -kb kin80 -km default. Hold 'boot0' button on MCU board, press 'reset', then release 'boot0'.

Parts

25
QtyValueFootprintReferences
41kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR5, R6, R7, R8
41kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR1, R2, R3, R4
43mmLED_THT:LED_D3.0mmLED1, LED2, LED3, LED4
4Conn_01x07Connector_Molex:Molex_PicoBlade_53047-0710_1x07_P1.25mm_VerticalJ1, J2, J5, J6
2Conn_01x11Connector_Molex:Molex_PicoBlade_53047-1110_1x11_P1.25mm_VerticalJ3, J4
2Conn_02x04_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_VerticalJ7, J8
1LOGOfootprints:q64logoG1
1LOGOfootprints:qmk-smallG2
1mounting padMountingHole:MountingHole_4.3mm_M4_PadH1
1mounting padMountingHole:MountingHole_6mmH2
1weact_STM32F4x1footprints:STM32F4x1_MiniF4U1

More from DmNosachev/kin80

3
  • 2 layers77 × 88 mmKinesis thumb pcb, the printed circuit board in 3D

    Kinesis thumb pcb

    DmNosachev/kin80

    Replacement PCB for Kinesis Contoured keyboards

    33 parts26CC-BY-SA-4.0
  • 2 layers125 × 19 mmKinesis top pcb, the printed circuit board in 3D

    Kinesis top pcb

    DmNosachev/kin80

    Replacement PCB for Kinesis Contoured keyboards

    27 parts26CC-BY-SA-4.0
  • 2 layers92 × 69 mmKin80ble, the printed circuit board in 3D

    Kin80ble

    DmNosachev/kin80

    Replacement PCB for Kinesis Contoured keyboards

    19 parts26CC-BY-SA-4.0

Similar boards

  • 2 layers159.5 × 30 mmType f, the printed circuit board in 3D

    Type f

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    25 parts3kApache-2.0
  • 2 layers113.5 × 95.1 mmSweep high, the printed circuit board in 3D

    Sweep high

    davidphilipbarr/Sweep

    Sweep - a small promicro based keyboard inspired by the Ferris.

    25 parts2.1k
  • 2 layers58.4 × 114.3 mmPicoPedal, the printed circuit board in 3D

    PicoPedal

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    25 parts915
  • 2 layers54 × 15 mmXyp gpib, the printed circuit board in 3D

    Xyp gpib

    xyphro/UsbGpib

    Versatile, cheap and portable USB to GPIB converter (USBTMC class based)

    25 parts690MIT
  • 2 layers50 × 76 mmVoron 0, the printed circuit board in 3D

    Voron 0

    dennisss/dacha

    Monorepo for awesome tools/projects/libraries

    25 parts397Apache-2.0
  • 2 layers237.5 × 102.9 mmStorage, the printed circuit board in 3D

    Storage

    jes/scamp-cpu

    A homebrew 16-bit CPU with a homebrew Unix-like-ish operating system.

    25 parts301Unlicense
  • 2 layers43.3 × 21 mmNanoS3 Carrier, the printed circuit board in 3D

    NanoS3 Carrier

    UnexpectedMaker/esp32s3

    Assorted files for my ESP32-S3 development boards

    25 parts296

Questions

How big is the Kin80 PCB?

It measures 92 × 69 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Kin80 use?

25 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Kin80 KiCad files?

From the DmNosachev/kin80 repository on GitHub, at the commit this page was made from: the board is controller-pcb/kin80/kin80.kicad_pcb and its schematic controller-pcb/kin80/kin80.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Kin80 design in my own project?

Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).