Skip to the content
2 layers34 × 101 mmNucDeck Right Top Controller PCB, the printed circuit board in 3D

NucDeck Right Top Controller PCB

dmcke5/NucDeck561

The Open Source DIY Handheld Gaming PC!

Size
34 × 101 mm
Copper layers
2
Thickness
1.6 mm
Parts
16
Nets
39
Pads
143
Tracks, vias
283, 39
Pours
1
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
28 Jul 2023
Updated
31 Jul 2024

Overview

NucDeck Right Top Controller PCB is an open-source printed circuit board by dmcke5, from the dmcke5/NucDeck repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 2-layer board of 34 × 101 mm with 16 parts on 39 nets, routed with 283 tracks and 39 vias.

It is built around the DRV5053OAQDBZRQ1. Its parts include 6 capacitors, 2 ICs and 2 connectors. It belongs with the RP2040 boards of this library.

Main components

1

README

README.md

Alt text

NucDeck

The Open Source DIY Handheld Gaming PC!

Refer to "NucDeck Assembly Instructions.PDF" for mechanical assembly details. Information for the electronics will be added once the controller PCB's are complete.

There are two different versions of the housing, Standard and NoRGB. The NoRGB version has had the RGB joystick surrounds removed to simplify printing. If you choose the NoRGB version you can leave all of the associated components off the PCB's to save on cost.

There are two different versions of the buttons, membrane and clicky. The Membrane buttons are shorter and are designed to be used with silicone membranes. I've included files for molds to make the membranes. If you have a resin printer I encourage you to give this a try as it improves the feel of the buttons dramatically. FDM printers will struggle to produce the accuracy required to make these parts. The clicky version is slightly taller and can be used without the membranes.

Total Cost of parts approximately: $311 USD

This is based on PCBway's pricing for the PCB's and is not including a NUC or any shipping charges. I've probably missed counting something so I would budget for a little more!

Here's a breakdown of the costs:

  • Digikey parts: $55 USD
  • PCB's (Set of 5 due to MOQ): $204 USD
  • Aliexpress Parts: $52 USD

If you can organise a group of 5 people who want a set of PCB's, you will greatly reduce your total cost to build.

Project Status
  • 3D Files
  • Software: V1.0 ready for testing. Motion controls not yet implemented
  • PCBs: Complete

Watch the series on Youtube as I design, build and test parts of this project:

I've found links for all of the parts on Aliexpress since its probably the cheapest option and will ship worldwide.

Parts List

Display

Any 1024x600 50 Pin RGB Panel with overall dimensions no greater than 164.9x100x3.3mm. This is the 700nit IPS panel I ended up using: https://www.aliexpress.com/item/1005005315348504.html

Display Driver

Pick the "PCB800812V1" option: https://www.aliexpress.com/item/1005004252996145.html

USB Touch Controller

Pick option "USB Controller": https://www.aliexpress.com/item/32976239800.html

Capacitive Touch Panel

This is the seller I used, but anyone selling for the same model tablet (Pritom K7) should do: https://www.aliexpress.com/item/1005002490383977.html

Joysticks

Joysticks are an Alps RKJX21224001. Here's a cheap seller on aliexpress: https://www.aliexpress.com/item/1005005264696228.html Joystick caps are Xbox One compatible.

Batteries

4x 605080 3000mah Lithium cells. Here's a cheap supplier on Aliexpress: https://www.aliexpress.com/item/32990176071.html

Info Screen

0.96" IPS 80x160 ST7735 TFT Display

You need the one these guys refer to as "Spliced Type". https://www.aliexpress.com/item/1005001598020071.html

Threaded Inserts

Measurments are: Thread x OD x Length

17x M2x3.2x4

10x M3x5x5

2x M3x5x4

https://www.aliexpress.com/item/1005003582355741.html

Standoffs

10x M2x6mm Male to Female Standoffs https://www.aliexpress.com/item/4001271908929.html

Trigger Springs

--NOTE-- Ignore the wire thickness in the Assembly Drawing, it is incorrect. I will fix it when I next need to make changes. Correct thickness listed here. These guys have a lot of different options, they are pretty cheap so I'd grab a few different wire thicknesses and test them out to see what you like. You need about 2mm ID on the coil section, so look for an ID of at least double the wire thickness greater than 2mm. I found 0.4mm to feel a bit too thin, and 0.7mm is about the limit of the trigger supports so 0.5-0.6mm is probably the sweet spot. https://www.aliexpress.com/item/1005004968066601.html

Trigger Magnets

You'll never need fridge magnets again! https://www.aliexpress.com/item/1005003794726533.html

RGB Lights

You'll need both RGB LED's and WS2811 IC's if you're adding RGB to your controller PCB's. These are the LED's I used. Any alternative in the same sized package should be fine too, just be cautious of differing pin configurations. https://www.aliexpress.com/item/1005003719602946.html

WS2811 IC's: https://www.aliexpress.com/item/32844615804.html

Screws

Here's a list of the screws required for assembly. This list is also in the assembly instructions. SCHS is just a standard allen key head screw. CSK is a countersunk head screw. Most bolt suppliers should have these, otherwise ebay or aliexpress is your friend.

12x M3x6mm SHCS 2x M2x16 CSK 9x M2x5 CSK 14x M2x4 SHCS

4s Cell Balancer

https://www.aliexpress.com/item/1005005827876691.html

Parts

16
QtyValueFootprintReferences
60.1uFCapacitor_SMD:C_0603_1608MetricC1, C2, C3, C4, C5, C6
4TestPointConnector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical3V3, GND1, SCL1, SDA1
2TestPointTestPoint:TestPoint_Pad_D1.5mmUSB_N1, USB_P1
12-1734592-2Parts:CONN22_2-1734592-2J2
1527450697Parts:CON_527450697_MOLJ1
1DRV5053OAQDBZRParts:DBZ0003A_NU3
1PicoRPi_Pico:RPi_Pico_SMD_THU1

More from dmcke5/NucDeck

3

Similar boards

  • 2 layers50.3 × 36.8 mmRHS Joystick PCB, the printed circuit board in 3D

    RHS Joystick PCB

    dmcke5/ZenDeck

    This is the second revision of my Mini PC based handheld Gaming PC! It is designed for a Beelink SER 5 Mini PC but could be adapted to other systems by changing the mounting brackets and outlet plate.

    3 parts133CERN-OHL-S-2.0
  • 2 layers116.3 × 31.2 mmGame Controller - Rear PCB, the printed circuit board in 3D

    Game Controller - Rear PCB

    dmcke5/XWii-Controller

    The Wii U gamepad layout is a fan-favourite for many gamers yet it is rarely used in the current generation of controllers.

    14 parts59CERN-OHL-S-2.0
  • 2 layers140.5 × 30 mmType e, the printed circuit board in 3D

    Type e

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    16 parts3kApache-2.0
  • 2 layers41.4 × 14.5 mmU2f zero, the printed circuit board in 3D

    U2f zero

    conorpp/u2f-zero

    U2F USB token optimized for physical security, affordability, and style

    16 parts2.4k
  • 2 layers122 × 37 mmV0-UmbilicalBoard, the printed circuit board in 3D

    V0-UmbilicalBoard

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    16 parts1.1kGPL-3.0
  • 2 layers152 × 57.6 mmVideoslotadapter, the printed circuit board in 3D

    Videoslotadapter

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    16 parts1kGPL-3.0
  • 2 layers36 × 63.4 mmSmart ringfinal layout, the printed circuit board in 3D

    Smart ringfinal layout

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    16 parts915

Questions

How big is the NucDeck Right Top Controller PCB PCB?

It measures 34 × 101 mm and has 2 copper layers, 1.6 mm thick.

What parts does the NucDeck Right Top Controller PCB use?

16 parts, built around the DRV5053OAQDBZRQ1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the NucDeck Right Top Controller PCB KiCad files?

From the dmcke5/NucDeck repository on GitHub, at the commit this page was made from: the board is PCB's/NucDeck Right Top Controller PCB/NucDeck Right Top Controller PCB.kicad_pcb and its schematic PCB's/NucDeck Left Front Controller PCB/NucDeck Left Controller PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the NucDeck Right Top Controller PCB design in my own project?

Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).