
LevelShifter
gusmanb/logicanalyzer
24 channel, 100Msps logic analyzer hardware and software

WHAT THE ARDUINO DOES ---------------------- The Arduino acts as the brain of the electronic dice. It waits for a button press, generates a random number from 1 to 6, and lights up the correct LEDs to show that number…
ADVAITH PCB is an open-source printed circuit board by Djmassi0101, from the Djmassi0101/PCB-Design repository on GitHub. It is a 2-layer board of 50 × 50 mm with 21 parts on 36 nets, routed with 65 tracks and 1 via.
Its parts include 7 resistors, 7 diodes, 1 connector and 1 switch. It belongs with the AVR (ATmega, ATtiny) boards of this library.
The Arduino acts as the brain of the electronic dice. It waits for a button press, generates a random number from 1 to 6, and lights up the correct LEDs to show that number as a dice face.
Push Button (1 digital input pin): The button is wired between a digital input pin and ground. When not pressed, the pin reads HIGH (held up by the Arduino's internal pull-up resistor). When pressed, it gets pulled to ground and reads LOW. The Arduino detects this LOW signal as a button press event.
LED Control (7 digital output pins): A standard dice face uses up to 7 LED positions arranged in a grid. Each LED position is driven by one output pin through a current-limiting resistor. The Arduino sets the relevant pins HIGH to turn LEDs on and LOW to turn them off.
The 7 positions map to each dice face like this:
Dice Face 1 -> Center only Dice Face 2 -> Top-right, Bottom-left Dice Face 3 -> Top-right, Center, Bottom-left Dice Face 4 -> All 4 corners Dice Face 5 -> All 4 corners + Center Dice Face 6 -> All 4 corners + Left-middle + Right-middle
Formula: R = (Vcc - Vf) / I
R = (5V - 2V) / 0.015A R = 3V / 0.015A R = 200 Ohms
Each LED gets a 200 Ohm resistor in series to safely limit current to 15mA.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | LED | LED_THT:LED_D5.0mm | D1, D2, D3, D4, D5, D6, D7 |
| 5 | R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3, R4, R5, R6, R7 |
| 2 | 200 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2 |
| 1 | Arduino_Nano_v3.x | Module:Arduino_Nano | A1 |
| 1 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Horizontal | J1 |
| 1 | SW_Push | Button_Switch_THT:SW_PUSH_6mm | SW1 |
The 17 most common of 21 parts.

gusmanb/logicanalyzer
24 channel, 100Msps logic analyzer hardware and software

mntmn/amiga2000-gfxcard
MNT VA2000, an Open Source Amiga 2/3/4000 Graphics Card (Zorro II/III), written in Verilog


hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

drandyhaas/KiCadRoutingTools
A set of Python/Rust tools to aid routing in KiCad

Arrow-air/project-quiver
Project Quiver documentation, designs, and project artifacts.


It measures 50 × 50 mm and has 2 copper layers, 1.6 mm thick.
21 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Djmassi0101/PCB-Design repository on GitHub, at the commit this page was made from: the board is ADVAITH_PCB.kicad_pcb and its schematic ADVAITH_PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Djmassi0101 before reusing the design.