

Axion Board
A fully broken out RP2040 based PCB
- Size
- 84 × 54.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 79
- Nets
- 79
- Pads
- 326
- Tracks, vias
- 903, 98
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 25 Jun 2023
- Updated
- 30 Nov 2024
Overview
Axion Board is an open-source printed circuit board by dj-shoko, from the dj-shoko/Axion-Board repository on GitHub. It is a 2-layer board of 84 × 54.5 mm with 79 parts on 79 nets, routed with 903 tracks and 98 vias.
It is built around the RP2040, SN74HCT125DRE4 and W25Q128JVSIQ, with the USBLC6-2SC6 and BSS138 among its other parts. Its parts include 19 capacitors, 14 connectors, 11 resistors, 11 transistors and 6 ICs. It belongs with the RP2040 boards of this library.
Main components
5RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)SN74HCT125DRE4
SOIC-14-40℃~+85℃ 1 22ns@5.5V,50pF 4 4.5V~5.5V 6mA 6mA 74HCT 80uA TTL-compatible CMOS Tri-State Unidirectional SOIC-14 Buffers, Drivers, Receivers, Transceivers ROHSTexas InstrumentsBuffers, Drivers, Receivers, TransceiversW25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)BSS138
SOT-23-55℃~+150℃ 1 N-channel 1.1Ω@10V、1.2Ω@4.5V 1.2V 1.7nC@10V 17.5pF 340mA 350mW 50V 6.5pF N-Channel SOT-23 MOSFETs ROHShongjiachengMOSFETs
README
README.mdInformation
Fully functionally working PCB utilizing the RP2040 MCU with all GPIO pins broken out and able to be utilized. Main purpose of the board is for usage in beatmania IIDX and Sound Voltex controllers. The PCB can be dropped into DJ DAO based beatmania IIDX controllers as a drop in replacement, utilizing the same pin layout as their original PCBs. Main functionality allows for the usage of 11 buttons, 11 5V LEDs, 2 RGB pins, and 2 quadrature encoders (analog should also be accepted in theory due to those being hooked up to all 4 analog pins). PS2 support should be possible as well on the current PCB, but untested at the moment. Two extra pins are also available either for RGB or other general purposes if needed.
Render and Schematics
Credits
- RP2040-designguide to get started on the PCB designing aspects and schematics.
- Pico Game Controller Firmware by SpeedyPotato for quick sanity check.
- USBemani by Progmem for the current firmware I'm using for this board. Personally forked firmware UF2 files here.
Parts
79| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100nF | Capacitor_SMD:C_0402_1005Metric | C1, C5, C6, C9, C10, C11, C12, C13, C14, C15, C19 |
| 11 | BSS138 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8, Q9, Q10, Q11 |
| 4 | 1uF | Capacitor_SMD:C_0402_1005Metric | C4, C8, C16, C17 |
| 4 | 330 | Resistor_SMD:R_0402_1005Metric | R8, R9, R10, R11 |
| 3 | 1k | Resistor_SMD:R_0402_1005Metric | R1, R2, R7 |
| 3 | LOGO | LOGO | G***, G***, G*** |
| 2 | 15pF | Capacitor_SMD:C_0402_1005Metric | C2, C3 |
| 2 | 27R | Resistor_SMD:R_0603_1608Metric | R5, R6 |
| 2 | 5k1 | Resistor_SMD:R_0402_1005Metric | R3, R4 |
| 2 | BUTTON8 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | BTN0, BTN8 |
| 2 | GPIO | Connector_PinHeader_1.27mm:PinHeader_1x02_P1.27mm_Vertical | J6, J7 |
| 1 | 10uF | Capacitor_SMD:C_0402_1005Metric | C7 |
| 1 | 12MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 330nF | Capacitor_SMD:C_0402_1005Metric | C18 |
| 1 | 500mA | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | 78M05_TO252-3 | Package_TO_SOT_SMD:TO-252-2 | U6 |
| 1 | BUTTON1 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | BTN1 |
| 1 | BUTTON10 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | BTN9 |
| 1 | BUTTON2 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | BTN2 |
| 1 | BUTTON3 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | BTN3 |
| 1 | BUTTON4 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | BTN4 |
| 1 | BUTTON5 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | BTN5 |
| 1 | BUTTON6 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | BTN6 |
| 1 | BUTTON7 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | BTN7 |
| 1 | BUTTON9 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | BTN10 |
| 1 | LED | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | LED |
| 1 | PS2 Header | Connector_RJ:RJ45_OST_PJ012-8P8CX_Vertical | J20 |
| 1 | QE1 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J17 |
| 1 | QE1A | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J3 |
| 1 | QE1B | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J4 |
| 1 | QE2 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J18 |
| 1 | QE2A | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J21 |
| 1 | QE2B | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J14 |
| 1 | RGB1 | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J16 |
| 1 | RGB2 | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J15 |
| 1 | RP2040 | Footprints:RP2040-QFN-56 | U3 |
| 1 | SN74HCT125DR | SN74HCT125N:SN74HCT125DR | U5 |
| 1 | SWD | Connector_PinHeader_1.27mm:PinHeader_1x05_P1.27mm_Vertical | J2 |
| 1 | SW_Push | Button_Switch_SMD:SW_SPST_PTS810 | SW1 |
| 1 | USB Header | Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J19 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U1 |
| 1 | XC6206PxxxMR-Regulator_Linear | Package_TO_SOT_SMD:SOT-23 | U4 |
Similar boards
- 2 layers112.7 × 114.2 mm

- 4 layers150 × 65 mm

- 4 layers99.5 × 65 mm

- 2 layers83 × 127 mm

Numpad
blafr103/pico-numpad
Hand-wired 17-key USB numpad on Pi Pico W. CircuitPython, diode matrix, event-driven scanning.
120 partsMIT - 2 layers148.2 × 114.4 mm

- 2 layers

Usb
wozniak-works/X1-palmrest-to-keyboard
A custom replacement board for the Lenovo ThinkPad X1 Carbon palmrest to transform it to keyboard with integrated powerbank and usb hub.
186 parts - 4 layers88.4 × 62.4 mm

- 2 layers135.3 × 78.4 mm

Mseq
MF-Room/mseq_pcb
KiCad 10 hardware design for MSeq embedded, the microcontroller implementation of the MSeq MIDI sequencer.
93 parts1CERN-OHL-S-2.0
Questions
How big is the Axion Board PCB?
It measures 84 × 54.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Axion Board use?
79 parts, built around the RP2040, SN74HCT125DRE4, W25Q128JVSIQ and USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Axion Board KiCad files?
From the dj-shoko/Axion-Board repository on GitHub, at the commit this page was made from: the board is Axion-Board.kicad_pcb and its schematic Axion-Board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Axion Board design in my own project?
Its repository states no licence, so its author keeps all rights: ask dj-shoko before reusing the design.