2 layers68.8 × 53.6 mm
ZArduino
zmaker/arduino_cookbook
gli sketch del nuovo progetto Arduino Cookbook e dei video di YouTube
46 parts269
2 layers68.6 × 53.3 mm
KiCAD AVR ISP programmer
DirkJMartens/AVR-programming-shield2Arduino shield with ZIP socket to program 28-pin ATMega microcontrollers
- Size
- 68.6 × 53.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 29
- Nets
- 20
- Pads
- 110
- Tracks, vias
- 93, 10
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 3 Feb 2021
- Updated
- 18 Sep 2023
Overview
KiCAD AVR ISP programmer is an open-source printed circuit board by DirkJMartens, from the DirkJMartens/AVR-programming-shield repository on GitHub. It is a 2-layer board of 68.6 × 53.3 mm with 29 parts on 20 nets, routed with 93 tracks and 10 vias.
It is built around the ATMEGA328P-PU. Its parts include 10 connectors, 8 resistors, 4 diodes, 3 capacitors and 1 IC. It belongs with the interfaces and adapters boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
1README
README.mdAVR-programming-shield
Arduino shield with ZIF socket to program sketches or bootloaders into 28-pin ATMega microcontrollers.
Usage for sketches:
- Install shield onto an Arduino Uno.
- Install the target AVR chip into the ZIF socket on the shield.
- Connect USB cable between your computer and Arduino Uno.
- The (blue) "Power" led should light up on the shield.
- Launch the Arduino IDE and load the "ArduinoISP" sketch from the "File - Examples" menu.
- Select "Tools - Board" to "Arduino Uno" and "Tools - Port" to the appropriate COM port
- Select "Sketch - Upload" to compile and upload the ArduinoISP sketch into your Uno.
- The (green) "Heartbeat" led should now fade in and out.
- Open the sketch you want to upload into the target AVR chip.
- Change the "Tools - Board" to e.g. "Arduino on a breadboard (8 MHz internal clock)".
- Change the "Tools - Programmer" to "Arduino as ISP"
- Select "Tools - Upload using Programmer" (not Upload).
- The sketch will be compiled and uploaded.
- During upload, the (amber) "Programming" led should light up.
- If the upload was successsful, the (green) "Heartbeat" light should fade in and out again.
- If the upload was unsuccesful, the (red) "Error" light should light up.
Usage for bootloader uploading:
- Repeat steps 1 through 8 above.
- Change "Tools - Board" to e.g. "Arduino on a breadboard (8 MHz internal clock)".
- Change "Tools - Programmer" to "Arduino as ISP".
- Change "Port" to the appropriate port.
- Select "Tools - Burn bootloader".
- Similar to above, the (amber) "Programming" led should light up during programming.
- Upon completion, the (green) "Heartbeat" led should fade or in case of a problem, the (red) "Error" light will light up.
Parts
29| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 2k4 | Resistor_SMD:R_0805_2012Metric | R2, R3, R4, R5 |
| 4 | CONN_01X01 | Socket_Arduino_Uno:Arduino_1pin | P5, P6, P7, P8 |
| 3 | 470 | Resistor_SMD:R_0805_2012Metric | R6, R7, R8 |
| 2 | 22p | Capacitor_SMD:C_0805_2012Metric | C1, C2 |
| 1 | 100n | Capacitor_SMD:C_0805_2012Metric | C3 |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 16.934MHz | Crystal:Crystal_HC49-4H_Vertical | Y1 |
| 1 | 5V-GND | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | ATmega328P-PU | Package_DIP:DIP-28_W7.62mm | U1 |
| 1 | Analog | Socket_Arduino_Uno:Socket_Strip_Arduino_1x06 | P2 |
| 1 | Digital | Socket_Arduino_Uno:Socket_Strip_Arduino_1x10 | P3 |
| 1 | Digital | Socket_Arduino_Uno:Socket_Strip_Arduino_1x08 | P4 |
| 1 | ERROR (Red) | LED_SMD:LED_0805_2012Metric | D2 |
| 1 | ICSP6 | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J2 |
| 1 | OK (Amber) | LED_SMD:LED_0805_2012Metric | D1 |
| 1 | POWER (Blue) | LED_SMD:LED_0805_2012Metric | D4 |
| 1 | PROGRAM (Green) | LED_SMD:LED_0805_2012Metric | D3 |
| 1 | PWR | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP1 |
| 1 | Power | Socket_Arduino_Uno:Socket_Strip_Arduino_1x08 | P1 |
| 1 | RESET | Button_Switch_THT:SW_TH_Tactile_Omron_B3F-10xx | SW1 |
Questions
How big is the KiCAD AVR ISP programmer PCB?
It measures 68.6 × 53.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the KiCAD AVR ISP programmer use?
29 parts, built around the ATMEGA328P-PU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the KiCAD AVR ISP programmer KiCad files?
From the DirkJMartens/AVR-programming-shield repository on GitHub, at the commit this page was made from: the board is KiCAD_AVR-ISP-programmer.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the KiCAD AVR ISP programmer design in my own project?
Its repository states no licence, so its author keeps all rights: ask DirkJMartens before reusing the design.
Similar boards
- 2 layers76.3 × 122.8 mm
Discipad pcb
coseyfannitutti/discipad
17-key numpad assembled with only through hole components, including usb type-c
63 parts221GPL-3.0 - 2 layers111.3 × 106.4 mm
Super Sixteen v1
matthewcieplak/super-sixteen
Code and schematics for the Super Sixteen Eurorack sequencer
141 parts171 - 2 layers247.6 × 99.2 mm
Romeo pcb
coseyfannitutti/romeo
Staggered 40% keyboard pcb that can be assembled with only through hole components, including USB Type-C
138 parts148GPL-3.0 - 2 layers90 × 140 mm
Drumkid
mattybrad/drumkid
Version 4 was the first successful working design, with full code, schematics, Gerbers, etc available on GitHub.
70 parts137 - 2 layers238.1 × 375.5 mm
- 2 layers
LM80C R6
leomil72/LM80C
A Z80-based homebrew computer withTMS9918, AY-3-8910, Z80 CTC, Z80 PIO, and Z80 SIO
153 parts123GPL-3.0 - 2 layers145.3 × 44.5 mm
