Skip to the content
4 layers127 × 97.3 mm68000sbc v1, the printed circuit board in 3D

A hardware fork of 68k nano, Matt Sarnoff's minimal single-board Motorola 68000 computer, adapted to use a PGA-68 packaged CPU (MC68HC000RC) instead of the original DIP-64, and re-laid-out on a 4-layer board.

Size
127 × 97.3 mm
Copper layers
4
Thickness
1.6 mm
Parts
49
Nets
107
Pads
451
Tracks, vias
2,540, 200
Pours
4
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
14 Jun 2026
Updated
20 Jun 2026

Overview

68000sbc v1 is an open-source printed circuit board by delphicchen, from the delphicchen/Make_68000_Great_Again repository on GitHub, published under the BSD-3-Clause licence. It is a 4-layer board of 127 × 97.3 mm with 49 parts on 107 nets, routed with 2,540 tracks and 200 vias.

It is built around the AS6C4008-55PCN, 74HC139D and 74HC14, with the TL16C550BN among its other parts. Its parts include 12 capacitors, 8 ICs, 7 resistors, 6 diodes and 6 connectors.

Main components

4

README

README.md

68k nano — PGA-68 / 4-layer edition

A hardware fork of 68k nano, Matt Sarnoff's minimal single-board Motorola 68000 computer, adapted to use a PGA-68 packaged CPU (MC68HC000RC) instead of the original DIP-64, and re-laid-out on a 4-layer board.

The electrical design — the memory map, glue logic, RAM/ROM/UART, the ROM firmware, and all software — is Matt Sarnoff's original work, used here under the BSD-3-Clause license (see below). This fork only changes the CPU package and the physical board layout; the schematic netlist is unchanged.

⚠️ This is an unofficial derivative and is not affiliated with, nor endorsed by, the original author.


What this fork changes

  • CPU package: DIP-64 → PGA-68. New footprint PadRows:MC68HC000_PGA68 whose pad numbers equal the DIP-64 pin numbers, so the existing CPU_NXP_68000 schematic symbol and the entire netlist are reused unchanged.
  • 4-layer stackup. A PGA's inner pins cannot "escape" on two layers, so the board is now: F.Cu / B.Cu signal, In1.Cu = GND plane, In2.Cu = VCC plane.
  • Re-laid-out and re-routed. Main components repositioned to clear the PGA; the board is fully auto-routed from the command line (FreeRouting headless) with a small custom maze router closing any nets FreeRouting leaves. Result: 0 unconnected, 0 copper/clearance DRC violations.
  • Verified pin-by-pin. Every pad was checked two ways — (1) it carries the same net as the original DIP board, and (2) its physical grid location matches the Motorola M68000 datasheet PGA pinout (Fig 11-2). See PGA68/verify_pins.py.

This fork's additions — see PGA68/

The notes in PGA68/ are written in 中文 (Traditional Chinese).

FileWhat it is
pin_mapping_DIP64_to_PGA68.mdDIP-64 ↔ PGA-68 pin map + datasheet bottom-view chart
verify_pins.pyPin-by-pin verification (netlist + datasheet placement)
4層佈線完成報告.mdRouting completion report (layers, DRC, file list)
convert_4layer.py, import_ses_4l.py, add_pours.py, maze_route_6.py, rebuild_pga_pcb.pyThe conversion / routing scripts
顯示器擴充指南.mdAdding a display (ESP32/FabGL serial terminal, or a bus video card)
設計隨筆.mdDesign notes (compute-power irony, "smart peripheral" philosophy)

Board files:

  • 68000sbc.kicad_pcb — the board, opens by default with the 68000sbc.kicad_pro project. 4-layer layout with components re-placed and the board fully re-routed; DRC-clean (0 unconnected, 0 copper/clearance violations).
  • 68000sbc_v1.kicad_pcb — the earlier layout, kept for reference (open directly in the PCB editor).
  • 68000sbc.sch (schematic, shared), and the footprint PadRows.pretty/MC68HC000_PGA68.kicad_mod.

A reusable, board-agnostic version of the headless routing workflow also exists as a Claude Code skill (kicad-autoroute); it is not part of this repo.


The original design & full documentation

Everything about how the computer actually works — features, the memory map, the bill of materials, how to build it, and the ROM firmware (boot process, interactive command shell, serial loader, debugger, system-call API) — is from the original project and is preserved unchanged here as README.original.md (and API.md, bom.txt, code/).

If you want to actually build and run this, read README.original.md first — the part counts, firmware, and usage are all there. This PGA-68 board needs the same BOM, just with a PGA-socketed MC68HC000RC in place of the DIP-64 CPU. A full English purchasing list for this board — generated from the actual footprints, with sockets, the 4-layer PCB spec, and build notes — is in BOM.md.

License

BSD 3-Clause License — Copyright (c) 2020 Matt Sarnoff. See LICENSE.

The PGA-68 conversion work added in this fork (the footprint, the PGA68/ scripts and notes, and the board re-layout) is contributed under the same BSD-3-Clause terms.

Parts

49
QtyValueFootprintReferences
100.1uFCapacitor_THT:C_Rect_L7.0mm_W2.0mm_P5.00mmC1, C2, C3, C4, C5, C6, C7, C8, C9, C10
41k*Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR4, R5, R6, R7
4MountingHole_2.7mm_M2.5_DIN965_PadMountingHole:MountingHole_2.7mm_M2.5_DIN965_PadH1, H2, H3, H4
210kResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR1, R2
210uFCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC11, C12
21N5817Diode_THT:D_DO-35_SOD27_P7.62mm_HorizontalD1, D2
228C256Package_DIP:DIP-28_W15.24mm_SocketU5, U7
2AS6C4008-55PCNPackage_DIP:DIP-32_W15.24mm_SocketU4, U6
110kResistor_THT:R_Array_SIP7RN1
112MHzOscillator:Oscillator_DIP-14X1
112MHzOscillator:Oscillator_DIP-8X2
11kResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR3
15V FTDI SERIALConnector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_HorizontalJ2
174HC139Package_DIP:DIP-16_W7.62mm_SocketU1
174HC14Package_DIP:DIP-14_W7.62mm_SocketU2
1BTN1Button_Switch_THT:SW_PUSH_6mmSW2
1CARDLED_THT:LED_D5.0mmD5
1CFCARD/IDEConnector_PinHeader_2.00mm:PinHeader_2x22_P2.00mm_VerticalJ4
1EXPANSION (B.Cu)PadRows:PadRow_1x25_P2.54mmJ6
1EXPANSION (F.Cu)PadRows:PadRow_1x25_P2.54mmJ5
1HALTLED_THT:LED_D5.0mmD6
1LEDLED_THT:LED_D5.0mmD4
1MC68HC000RC10PadRows:MC68HC000_PGA68U3
1POWERLED_THT:LED_D5.0mmD3
1POWER SELECTConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJP1
1RESETButton_Switch_THT:SW_PUSH_6mmSW1
1RTC (SparkFun BOB-10160)Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_VerticalJ3
1TL16C550Package_DIP:DIP-40_W15.24mm_SocketU8
1USB_BConnector_USB:USB_B_OST_USB-B1HSxx_HorizontalJ1

Similar boards

  • 2 layers127 × 90.8 mm68000sbc, the printed circuit board in 3D

    68000sbc

    demik/oldworld

    Development ressources for Old World Macintosh (68k and NuBus PPC) and a few related things…

    53 parts27CERN-OHL-P-2.0
  • 2 layers127 × 127 mmMorseboard-8088, the printed circuit board in 3D

    Morseboard-8088

    ifilot/morseboard-8088

    Single board computer designed around the 8088 processor

    61 parts
  • 2 layers172.7 × 63.5 mm8088sbc, the printed circuit board in 3D

    8088sbc

    74hc595/8088sbc

    Minimal 8088 single board computer

    59 parts34BSD-3-Clause
  • 2 layers160 × 100 mmCPU09RAM, the printed circuit board in 3D

    CPU09RAM

    roberto314/kees1948_Boards

    kees 1948 Uniflex Remake

    48 parts1
  • 2 layersByteFrost, the printed circuit board in 3D

    ByteFrost

    gilkeidar/ByteFrost

    Software Tools for ByteFrost - A Breadboard 8-Bit Computer

    36 parts5
  • 4 layers271.8 × 147.3 mmSF68, the printed circuit board in 3D

    SF68

    scefrom/SF68

    A board featuring the Motorola 68000

    130 parts2
  • 2 layers234 × 100 mmV2b, the printed circuit board in 3D

    V2b

    KITTY-6502/hardware

    the KITTY is a 65c02 homebrew kit microcomputer designed around text mode graphics and cartridge media. It is fully open source, and uses exclusively in-production parts.

    147 parts

Questions

How big is the 68000sbc v1 PCB?

It measures 127 × 97.3 mm and has 4 copper layers, 1.6 mm thick.

What parts does the 68000sbc v1 use?

49 parts, built around the AS6C4008-55PCN, 74HC139D, 74HC14 and TL16C550BN. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the 68000sbc v1 KiCad files?

From the delphicchen/Make_68000_Great_Again repository on GitHub, at the commit this page was made from: the board is 68000sbc_v1.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the 68000sbc v1 design in my own project?

Its repository publishes it under the BSD-3-Clause licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).