

Serendipity rp2040
Serendipity keyboard designed by @ojthetiny and me.
- Size
- 287.3 × 97.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 165
- Nets
- 116
- Pads
- 790
- Tracks, vias
- 591, 41
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 15 Feb 2024
- Updated
- 15 Feb 2024
Overview
Serendipity rp2040 is an open-source printed circuit board by dededecline, from the dededecline/Serendipity repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 287.3 × 97.8 mm with 165 parts on 116 nets, routed with 591 tracks and 41 vias.
It is built around the RP2040, W25Q128JVSIQ and PRTR5V0U2X. Its parts include 63 diodes, 17 capacitors, 7 resistors, 4 ICs and 2 switches. It belongs with the keyboards and input boards and the RP2040 boards of this library.
Main components
3RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHPRTR5V0U2X
SOT-143-55℃~+125℃ 0.3pF、0.8pF 100W 10V、15V 5V 6.5V 6A 80nA ESD IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Three channels Unidirectional SOT-143 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)
README
README.mdSerendipity

Board Details
Serendipity is a collaboration between dededecline and liv
Photos by group buy participants can be found here!
More info can be found on the Geekhack interest check.
Hardware
- Back Case Screws: 4x m3x14mm
- Front Case Screws: 4x m3x8mm
- Weight Screws: 2x m3x5mm countersunk
- Plate Screws: 8x m3x8mm
- Badge Screws: 2x m2x5mm
- DB Screws: 4x m2x5mm
- O-Rings: 16x 1.5mmx2.5mm, 70 duro recommended
- Feet: 2x Geonworks 60% feet
Additional Information
The o-rings are required for the build to work properly. For each plate screw, one o-ring goes between the top case piece and the plate, and another goes between the plate and the screw head. Do not overly tighten plate screws.
All files required for manufacturing are present in this repository.
All relevant information about the board should be in the Geekhack interest check.
DISCLAIMER
These components have been tested and confirmed to work properly. I am not liable for any issues stemming from usage of these files. Order at your own risk. Support will not be provided, but pull requests will be reviewed and possibly accepted.
Parts
165| Qty | Value | Footprint | References |
|---|---|---|---|
| 63 | D_Small | Diode_SMD:D_SOD-123 | D1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +47 |
| 52 | MX-NoLED | MX_Alps_Hybrid:MX-1U-NoLED | MX10, MX11, MX12, MX13, MX14, MX15, MX17, MX18, MX19, MX20, MX21, MX22, MX23, MX24, MX25, MX27 +36 |
| 10 | .1u | Capacitor_SMD:C_0402_1005Metric | C3, C5, C6, C9, C10, C11, C12, C13, C14, C15 |
| 7 | MX-NoLED | MX_Alps_Hybrid:MX-1.5U-NoLED | MX2, MX5, MX16, MX50, MX60, MX62, MX64 |
| 4 | 1u | Capacitor_SMD:C_0402_1005Metric | C4, C8, C16, C17 |
| 3 | 1k | Resistor_SMD:R_0402_1005Metric | R1, R4, R5 |
| 2 | 22pF | Capacitor_SMD:C_0402_1005Metric | C1, C2 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric | R2, R3 |
| 2 | MX-NoLED | MX_Alps_Hybrid:MX-3U-ReversedStabilizers-NoLED | MX26, MX41 |
| 1 | 10u | Capacitor_SMD:C_0402_1005Metric | C7 |
| 1 | 12MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 220 | Resistor_SMD:R_0402_1005Metric | R8 |
| 1 | Boot | Button_Switch_SMD:SW_SPST_TL3342 | SW1 |
| 1 | LOGO | Components:OJ LOGO | G*** |
| 1 | MX-NoLED | cipulot_parts:MX-1.25U | MX3 |
| 1 | MX-NoLED | MX_Alps_Hybrid:MX-2.25U-ReversedStabilizers-NoLED | MX59 |
| 1 | MX-NoLED | cipulot_parts:MX-1U | MX1 |
| 1 | MX-NoLED | MX_Alps_Hybrid:MX-1.75U-NoLED | MX63 |
| 1 | MX-NoLED | MX_Alps_Hybrid:MX-2.25U-NoLED | MX4 |
| 1 | MX-NoLED | MX_Alps_Hybrid:MX-7U-ReversedStabilizers-NoLED | MX32 |
| 1 | MX-NoLED | cipulot_parts:MX-1.75U-FLIPPED | MX6 |
| 1 | MX-NoLED | MX_Alps_Hybrid:MX-6U-Centered-ReversedStabilizers-NoLED | MX31 |
| 1 | PRTR5V0U2X | random-keyboard-parts:SOT143B | U4 |
| 1 | RP2040 | cipulot_parts:RP2040-QFN-56 | U1 |
| 1 | R_0402_1005Metric | Resistor_SMD:R_0402_1005Metric | R9 |
| 1 | Reset | Button_Switch_SMD:SW_SPST_TL3342 | SW2 |
| 1 | SM04B | Connector_Molex:Molex_Pico-EZmate_78171-0004_1x04-1MP_P1.20mm_Vertical | J1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U2 |
| 1 | XC6206PxxxMR | Package_TO_SOT_SMD:SOT-23 | U3 |
More from dededecline/Serendipity
1- 2 layers288.9 × 98.4 mm

Similar boards
- 2 layers181 × 97 mm

OpenDeck r3.1.2
shanteacontrols/OpenDeck
A platform for building interactive control and sensing devices using MIDI and OSC built with Zephyr RTOS.
262 parts960Apache-2.0 - 2 layers285 × 94.6 mm

PH60Slim Choc
ph-design/PH60-SC
A printable low-profile 60% wireless mechanical keyboard kit powered by ZMK firmware.
219 parts132 - 2 layers226.5 × 75 mm

Gridiron
dededecline/Gridiron
Gridiron keyboard designed by me. All files for production are inside this repository.
159 parts13GPL-3.0 - 4 layers50.8 × 25.4 mm

- 2 layers287.3 × 98.4 mm

Boethia60
arviceblot/boethia60
A low profile, hotswap keyboard inspired by the HHBK layout.
161 parts5MIT - 2 layers228.6 × 77.7 mm

- 4 layers22.9 × 63 mm

RP2040 Motion Logger
rishikesh2715/RP2040_Motion_Logger
An RP2040 based microcontroller with an ICM-42688 IMU, 1S Battery Charger, SD Card Connector, RGB Led, and USB Type-C connector
70 parts1MIT - 2 layers

Inett 60 PCB
TeddyDo915K/Nett-Sixty-PCB
This is a work in progress to create a replacement PCB for one of my favorites keyboard that I own.
158 parts1MIT
Questions
How big is the Serendipity rp2040 PCB?
It measures 287.3 × 97.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Serendipity rp2040 use?
165 parts, built around the RP2040, W25Q128JVSIQ and PRTR5V0U2X. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Serendipity rp2040 KiCad files?
From the dededecline/Serendipity repository on GitHub, at the commit this page was made from: the board is PCB/Solder/Kicad/Serendipity-rp2040.kicad_pcb and its schematic PCB/Hotswap/KiCad/Hotswap.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Serendipity rp2040 design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).