

WinLED: BLE-controlled LED driver (ESP32 + AD5724R, KiCad PCB)
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 32
- Nets
- 59
- Pads
- 172
- Tracks, vias
- 372, 13
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 6 Aug 2026
- Updated
- 6 Aug 2026
Overview
Dado is an open-source printed circuit board by DCunha27, from the DCunha27/led-driver-winled repository on GitHub. It is a 2-layer board with 32 parts on 59 nets, routed with 372 tracks and 13 vias.
It is built around the ADS1015BQDGSRQ1, AD5724RBREZ and LM1117MPX-50NOPB, with the MAX14932AASE+ and SI8040AA-B-IU among its other parts. Its parts include 17 capacitors, 7 ICs, 4 connectors and 3 resistors. It belongs with the ESP32 and AVR (ATmega, ATtiny) boards of this library.
Main components
5ADS1015BQDGSRQ1
VSSOP-10-0.5mm-40℃~+125℃ 0.5LSB 12 128Hz、250Hz、490Hz、920Hz、1.6kHz、2.4kHz、3.3kHz 150uA 1MHz 2 256mV、512mV、1.024V、2.048V、4.096V、6.144V 2V~5.5V 3.3kHz 5ppm/℃ Built-in Built-in I2C Sigma-Delta Support Yes VSSOP-10-0.5mm Analog to Digital Converters (ADC) ROHSTexas InstrumentsAnalog To Digital Converters (ADC)AD5724RBREZ
TSSOP-24-EP-40℃~+85℃ 10us 12 1LSB 4 4.5V~16.5V 500nA Integrated buffer、Power-on reset、Power-down mode、Bipolar output、Built-in reference source、Over temperature protection、Output short-circuit protection SPI、QSPI、MICROWIRE Voltage Buffer TSSOP-24-EP Digital to Analog Converters (DAC) ROHSAnalog DevicesDigital To Analog Converters (DAC)LM1117MPX-50NOPB
SOT-2230.003%Vout 0℃~+125℃@(Ta) 1 1.2V@(800mA) 10mA 15V 5V 61dB@(120Hz) 800mA Fixed Over Current Protection、Over Temperature Protection Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSonsemiVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMAX14932AASE+
SOIC-16-40℃~+125℃ 1.71V~5.5V 1.71V~5.5V 1Mbps 2 2 25kV/us 2750 High Level SOIC-16 Digital Isolators ROHSMaxim Integrated (Analog Devices)Digital IsolatorsSI8040AA-B-IU
QSOP-16Digital IsolatorsSkyworks Solutions
README
README.mdWinLED — Controllable LED Driver with BLE Control & Monitoring
Final-year project (Projeto em Engenharia Eletrotécnica) — Universidade de Aveiro, BSc in Electrical Engineering.
A high-accuracy LED driver for illumination / Visible Light Communication (VLC), with a custom control & monitoring PCB, ESP32 firmware, wireless control over Bluetooth Low Energy (BLE), and a companion Windows application (WinLED).
⚠️ Team project — this repository contains my contribution (control firmware, DAC/ADC drivers, BLE layer and control-board design). Shared deliverables are included as documentation.
✨ Overview
The system drives power LEDs with a precise, adjustable current and reports back real-time measurements, all controllable wirelessly.
- MCU: ESP32 (SPI, BLE)
- D/A conversion: Analog Devices AD5724R (quad, 16-bit, SPI) — sets the LED current reference
- A/D monitoring: ADS1015 — reads back current/voltage
- Isolation: digital isolator (ISO1541) between logic and power stages
- Wireless: BLE using the NimBLE stack
- Host app: WinLED (Windows) to configure channels and visualise telemetry
🗂️ Repository structure
firmware/
CodArduino/ initial Arduino test code (DAC bring-up)
main/ main firmware (modular: DAC/ADC/BLE/command layers)
nimmain/ BLE firmware using the NimBLE stack
hardware/
dado.kicad_* control & monitoring PCB (KiCad project)
docs/
FinalReport.pdf project report
pdb_esquematico.jpg schematic capture
pdb_PCI.jpg PCB capture🔧 Firmware architecture
The firmware is split into clean layers:
dac_driver— SPI driver for the AD5724R (channel setup, code → current)adc_driver— reads back measurements from the ADS1015ble_handler— BLE service/characteristics (NimBLE)command_layer— parses commands from the host app and maps them to actions
🛠️ Tech stack
ESP32 · C/C++ (Arduino) · NimBLE · SPI · I²C · KiCad · AD5724R · ADS1015
🚀 Build & flash
- Open the sketch in
firmware/main/(Arduino IDE / PlatformIO). - Install the NimBLE-Arduino library.
- Select an ESP32 board and flash.
- Open the PCB in
hardware/with KiCad 7+.
📈 What I learned
Hardware–firmware–software integration, precision D/A conversion, custom PCB design from schematic to Gerbers, and wireless embedded protocols (SPI + BLE).
Part of my engineering portfolio — see my other projects.
Parts
32| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100nF | Capacitor_SMD:C_0402_1005Metric | C1, C2, C3, C4, C5, C9, C10, C12, C14, C23 |
| 4 | 10µF | Capacitor_SMD:C_0402_1005Metric | C13, C15, C16, C17 |
| 2 | 4.7K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R2, R3 |
| 2 | ADS1015BQDGSRQ1 | Library:ADS1015BQDGSRQ1 | IC4, IC5 |
| 1 | 10K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1 |
| 1 | 10uF | Capacitor_SMD:C_0402_1005Metric | C11 |
| 1 | 1uF | Capacitor_SMD:C_0402_1005Metric | C7 |
| 1 | 4,7uF | Capacitor_SMD:C_0402_1005Metric | C8 |
| 1 | AD5724RBREZ | Library:SOP65P640X120-25N | IC3 |
| 1 | AP7361-33E-13 | Library:AP7361-33E-13 | IC7 |
| 1 | Arduino_Nano_ESP32 | Module:Arduino_Nano | A1 |
| 1 | Fonte | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J4 |
| 1 | LED1 | Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J1 |
| 1 | LED2 | Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J2 |
| 1 | LED3 | Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J3 |
| 1 | LM1117MPX-50NOPB | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | IC6 |
| 1 | MAX14932AASE+ | Library:MAX14932AASE+ | IC2 |
| 1 | SI8040AA-B-IU | Library:SI8040AA-B-IU | IC1 |
Similar boards
- 6 layers90.2 × 95.9 mm

- 2 layers53.5 × 26.5 mm

- 2 layers70 × 45 mm

- 2 layers59 × 29.5 mm

- 2 layers59.3 × 71.4 mm

- 2 layers50 × 23.2 mm

Analog
hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI
32 parts1kGPL-3.0 - 2 layers136.8 × 54.2 mm

Retropie zero
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
32 parts915 - 2 layers

Questions
What parts does the Dado use?
32 parts, built around the ADS1015BQDGSRQ1, AD5724RBREZ, LM1117MPX-50NOPB and MAX14932AASE+. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Dado KiCad files?
From the DCunha27/led-driver-winled repository on GitHub, at the commit this page was made from: the board is hardware/dado.kicad_pcb and its schematic hardware/dado.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Dado design in my own project?
Its repository states no licence, so its author keeps all rights: ask DCunha27 before reusing the design.