Skip to the content
4 layers100 × 90 mmFmc, the printed circuit board in 3D

MIPI DSI transmitter core for Xilinx FPGAs (work in progress)

Size
100 × 90 mm
Copper layers
4
Thickness
1.6 mm
Parts
149
Nets
139
Pads
879
Tracks, vias
9,318, 641
Pours
4
Routed
Yes
KiCad
KiCad 4
Created
25 Apr 2017
Updated
25 Apr 2017

Overview

Fmc is an open-source printed circuit board by daveshah1, from the daveshah1/DSITx repository on GitHub, published under the MIT licence. It is a 4-layer board of 100 × 90 mm with 149 parts on 139 nets, routed with 9,318 tracks and 641 vias.

It is built around the LMR64010XMF, TPS65135RTE and MCP1825T-ADJE/ET, with the MBR0530 among its other parts. Its parts include 96 resistors, 30 capacitors, 11 ICs, 3 diodes and 3 connectors. It belongs with the fPGA and programmable logic boards of this library.

Main components

4

README

README.md

MIPI DSI FPGA LCD Interface

This is a work-in-progress core to interface advanced MIPI DSI displays with a Xilinx 7-series FPGA. The current display target is the Sony Z5 Premium LCD (AUO H546UAN01.0 or Sharp LS055D1SX05) which is a 5.5" 4k (2160x3840) LCD. At the moment I am running it in a mode where content is upscaled by the panel from 1080x1920, as 4k content must be compressed using VESA DSC or Qualcomm FBC. I am working on an encoder for the former.

The only DSI mode currently supported is Command Mode, Video Mode is still being worked on and is not as well documented for the target panels. This panel works in dual DSI mode, so two transmitters are used each transmitting half of each line. Single-link command mode panels would also work, with by only instantiating one dsi_tx_cmd_mode_top.

A demo project is included for the afforementioned panel and config. It was designed for an FMC breakout board I've built for the Genesys 2 development board with a Kintex-7 FPGA. Unfortunately a signal integrity issue on this board means I have to run the DSI link at its lowest rate, 200Mbps, which limits the framerate to about 30fps. Nonetheless, the design files for this board are included if you want a circuit to run the display, although in any system you develop the MIPI DSI translator resistors should be located much closer to the FPGA to avoid the issues I've had.

The final intended use of this interface is for a larger project I am working on, the openMixR 4k headset.

Parts

149
QtyValueFootprintReferences
2410uCapacitors_SMD:C_0805C1, C2, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23 +8
20120Resistors_SMD:R_0402R4, R5, R12, R13, R16, R17, R20, R21, R34, R35, R38, R39, R42, R43, R46, R47 +4
2022Resistors_SMD:R_0402R3, R10, R11, R14, R15, R18, R19, R22, R33, R36, R37, R40, R41, R44, R45, R48 +4
2051Resistors_SMD:R_0402R23, R24, R25, R26, R27, R28, R29, R30, R31, R32, R53, R54, R55, R56, R57, R58 +4
1410kResistors_SMD:R_0402R1, R63, R65, R67, R73, R75, R77, R82, R83, R86, R88, R90, R92, R94
6MCP1825T-ADJECustom Parts:SOT-223-6U2, U4, U7, U8, U9, U10
54.7kResistors_SMD:R_0402R78, R79, R80, R84, R87
2100nCapacitors_SMD:C_0402C4, C29
222µCapacitors_SMD:C_1206C28, C30
2330Resistors_SMD:R_0402R95, R96
258.3kResistors_SMD:R_0402R85, R89
2LEDLEDs:LED_0805D2, D3
2RK3288-CAMCustom Parts:3-1734592-0CAM1, CAM2
10Resistors_SMD:R_0402R2
110u/0.6AInductors_NEOSID:Neosid_Inductor_SM-NE29_SMD1008L1
1120kResistors_SMD:R_0402R71
1120pCapacitors_SMD:C_0402C6
113.3kResistors_SMD:R_0402R69
119.1kResistors_SMD:R_0402R91
11MResistors_SMD:R_0402R64
12.2u/1AInductors_NEOSID:Neosid_Inductor_SM-NE29_SMD1008L2
122.6kResistors_SMD:R_0402R74
1226kResistors_SMD:R_0402R68
134kResistors_SMD:R_0402R81
135.7kResistors_SMD:R_0402R66
14.7u/50VCapacitors_SMD:C_1206C7
14.7µH/SRN6045Custom Parts:SRN6045L3
1422kResistors_SMD:R_0402R70
14k7Resistors_SMD:R_0402R76
1542kResistors_SMD:R_0402R72
156.2kResistors_SMD:R_0402R93
1CL320Housings_SOIC:SOIC-8-1EP_3.9x4.9mm_Pitch1.27mmU5
1FMC-HPC-AC701Custom Parts:ASP-134488-01P1
1H546UAN0.1Custom Parts:60pin-0.35mmU6
1LCD_IDMeasurement_Points:Measurement_Point_Round-SMD-Pad_SmallP3
1LMR64010TO_SOT_Packages_SMD:SOT-23-5U1
1MBR0530Diodes_SMD:SOD-123D1
1POLY1AFuse_Holders_and_Fuses:Fuse_SMD1206_ReflowF1
1PWRPin_Headers:Pin_Header_Straight_1x03P4
1TPS56220TO_SOT_Packages_SMD:SOT-23-6U11
1TPS65135Housings_DFN_QFN:QFN-16-1EP_3x3mm_Pitch0.5mmU3

Similar boards

  • 4 layers85.5 × 79.5 mmLcdboard, the printed circuit board in 3D

    Lcdboard

    daveshah1/openMixR

    4k Mixed Reality headset

    35 parts40MIT
  • 2 layers17.9 × 5.8 mmINA1620 headphone amp, the printed circuit board in 3D

    INA1620 headphone amp

    daumemo/DIY-Micro-USB-C-DAC-Amplifier

    A DIY headphone amplifier based on INA1620 and USB-C DAC

    23 parts15MIT
  • 2 layers90 × 88.4 mmAdc, the printed circuit board in 3D

    Adc

    zapta/daq

    A modular data acquisition system.

    117 parts1
  • 4 layers48.8 × 55.3 mmFPGA Lockin, the printed circuit board in 3D

    FPGA Lockin

    Cstubbs56/FPGA-Lockin-Amplifier-PCB

    129 parts
  • 2 layers103.8 × 50.9 mmFINAL final, the printed circuit board in 3D

    FINAL final

    PavitpalSingh2004/TRUESENSE_V2

    TrueSense V2 is a compact high-speed reflection spectrometer using the Hamamatsu C12880MA, ESP32-S3, custom PCBs, high-speed ADC acquisition, FT2232H USB, Wi-Fi/UDP streaming, and a PyQt6 GUI for real-time spectrum…

    113 parts
  • 4 layers40 × 40 mmCleanLVSupply, the printed circuit board in 3D

    CleanLVSupply

    BlockWorker/ModularAudio

    Compact, modular, versatile, hi-fi audio system concept.

    81 parts2
  • 2 layers41.3 × 27.9 mmUV PS, the printed circuit board in 3D

    UV PS

    Dirkmeister/UV-Backlight-Prototype

    A UV led backlight for pcb imaging. PCB is designed for prototyping.

    16 partsMIT

Questions

How big is the Fmc PCB?

It measures 100 × 90 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Fmc use?

149 parts, built around the LMR64010XMF, TPS65135RTE, MCP1825T-ADJE/ET and MBR0530. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Fmc KiCad files?

From the daveshah1/DSITx repository on GitHub, at the commit this page was made from: the board is hardware/fmc-v1.2/fmc.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Fmc design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).