

Titania3
The project goal is to create a datalogger small and light enough for an 18mm A8-3 rocket, but capable enough to use as a backup logger for mid and high power flights.
- Size
- 16.4 × 48.7 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 48
- Nets
- 54
- Pads
- 169
- Tracks, vias
- 416, 52
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 25 Feb 2026
- Updated
- 26 Feb 2026
Overview
Titania3 is an open-source printed circuit board by Danzibob, from the Danzibob/Titania3 repository on GitHub. It is a 4-layer board of 16.4 × 48.7 mm with 48 parts on 54 nets, routed with 416 tracks and 52 vias.
It is built around the STM32L072CBT6, BMP580 and MX25R3235FM1IL0, with the BMI260, MCP73831 and XC6206P332MR among its other parts. Its parts include 12 capacitors, 11 resistors, 6 ICs, 4 diodes and 1 connector. It belongs with the STM32 boards of this library.
Main components
8STM32L072CBT6
LQFP-48(7x7)-40℃~+85℃ 1.65V~3.6V 128KB 12bit 12bit 20KB 32 Bit 32MHz 37 6KB ARM Cortex-M0+ Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)BMP580
LGA-10(2x2)-40℃~+85℃ 0.5pa/K 1.73V~3.6V 30Kpa~1.25bar 5.5uA 6pa 75pa I2C、SPI、I3C LGA-10(2x2) Pressure Sensors ROHSBosch SensortecPressure SensorsMX25R3235FM1IL0
SOP-8-40℃~+85℃ 1.65V~3.6V 100,000 cycles 20 Years 3.2ms 32Mbit 80MHz SPI SOP-8 NOR FLASH ROHSMXICNOR FLASHBMI260
LGA14-(2.5x3)-40℃~+85℃ 1.7V~3.6V 16bit IMU SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps LGA14-(2.5x3) Accelerometers ROHSBosch SensortecAccelerometersMCP73831
UncategorisedMicrochip TechnologyXC6206P332MR
SOT-23-40℃~+85℃@(Ta) 1 1uA 200mA 3.3V 6V Fixed Over Current Protection Positive SOT-23-3L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) Regulators1N5819WS
SOD-3231 Independent 1A 25A 40V 500uA@40V 600mV@1A SOD-323 Schottky Diodes ROHSGuangdong HottechSchottky DiodesBZT52B3V3
SOD-123Zener Diodeshongjiacheng
README
README.mdTitania III
This project is the third iteration of the tiny titania data-logger for model rocketry.
The project goal is to create a datalogger small and light enough for an 18mm A8-3 rocket, but capable enough to use as a backup logger for mid and high power flights. An additional aim of this project is to run on a rechargable coin cell battery instead of the usual LiPo. This restriction heavily limits our component choices because of the low current provided by these coin cells (usually <15mA sustained).
Docs
Features
- Logs barometric pressure, temperature, acceleration and rotation data
- Up to 600Hz logging in bursts, 200Hz normal target
- Logs save to flash memory (4MB)
- Buzzer / beeper for basic output & assist in recovery
- PCB-edge USB-A for firmware programming, data offload & charging
- Fits in an 18mm rocket body tube
- Mass of < 10g (including battery)
- LIR1254 rechargable coin cell power source
Logging format
In order to maximise the logging time available in the flash, we make a trade-off for minimizing storage over precision. This project aims to allow for the following flight timings to fit in the 4MB log flash:
| Flight Phase | Duration (up to) | Storage Priority | Storage Allocation | Max Data Rate |
|---|---|---|---|---|
| Pad time | 1 hour | Small constant storage | <1% (~100B) | N/A |
| Ascent | 2 minutes | Most important | ~75% (3 MB) | 25 kB/s |
| Descent | 20 minutes | Less important | ~25% (1 MB) | ~800 B/s |
| Recovery | 2 hours | No storage required | N/A | N/A |
BMP580
Barometric pressure
- Sensor measurement range: 30-125kPa
- Absolute accuracy: +/- 50Pa
- Corresponds to ~4m of altitude near sea level
- Relative accuracy: 6Pa per 10kPa
- ~0.5m / 1km of altitude
- Relative accuracy is what's important for determining the altitude of a flight
- Resolution at oversampling levels (RMS noise @ 100kPa):
- Low (1x) = 0.78Pa @ up to 498Hz
- Standard (x4) = 0.41Pa @ up to 255Hz
- High (x16) = 0.21Pa @ up to 87Hz
- Highest (x128) = 0.08Pa @ up to 12Hz
On pad, take an f32 Highest resolution sample over a few seconds.
- Massive overkill but nice to have accurate ground pressure
In flight, record u16 pressure with LSB = 2Pa.
- This gives us spatial resolution of ~16cm
- And a range of 0-131kPa, which fully covers the sensor range
- Also easy to convert by bitshifting
Temperature
- While ascending, the rocket is moving too fast for the air temperature inside the chassis to equalize
- Therefore, only take temperature readings on the pad and during descent
- Based on the Troposphere lapse rate of ~ 6.5K/km, and the 10km ceiling for this logger, we need to deal with at least a range of 60 degrees
- Combined with a ground temperature range of -10 to 50C this requires a total range of at least 120 degrees
- f16 gives us plenty of resolution within this range
On pad/boot, record a temperature value over several seconds (f16)
- We can combine this with ground pressure for better altitude estimates
Not much point taking temperature readings on ascent
- Could maybe store an i8?
On descent, the barometer will be exposed to the open air at slower speed.
- Take f16 measurements at regular intervals
- These can be used to accurately profile the air column
Sampling & Data Rates
- Pad - take a set of samples over a preset startup window (10s?)
- 6 bytes (f32 pressure and f16 temp)
- Potentially worth repeating every 30 seconds until launch?
- Ring buffer to save last N measurements before launch?
- Ascent - Log Pressure (and maybe temp) at high frequency
- 500Hz * u16(+i8) = 1kB/s (1.5kB/s) = 4% (6%) of quota
- 250Hz * u16(+i8) = 500B/s (750B/s) = 2% (3%) of quota
- 100Hz * u16(+i8) = 200B/s (300B/s) = <1% (~1%) of quota
- Descent - Significantly lower frequency; log pressure & temp at full resolution
- 10Hz * (u16+f16) = 40B/s = 5% of quota
- Ground
- No logging required
Parts
48| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 100nF | Capacitor_SMD:C_0402_1005Metric | C5, C6, C7, C8, C9, C11, C13 |
| 6 | 10K | Resistor_SMD:R_0402_1005Metric | R3, R4, R5, R6, R8, R9 |
| 3 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C1, C2, C12 |
| 2 | 1.0uF | Capacitor_SMD:C_0402_1005Metric | C3, C4 |
| 1 | 1N5819WS | Diode_SMD:D_SOD-323 | D2 |
| 1 | 33K | Resistor_SMD:R_0402_1005Metric | R10 |
| 1 | 470R | Resistor_SMD:R_0402_1005Metric | R7 |
| 1 | 470R (>=250mW) | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 68K | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | 82K | Resistor_SMD:R_0402_1005Metric | R11 |
| 1 | BMI260 | Package_LGA:Bosch_LGA-14_3x2.5mm_P0.5mm | U2 |
| 1 | BMP580 | Package_LGA:ST_HLGA-10_2x2mm_P0.5mm_LayoutBorder3x2y | U3 |
| 1 | BOOT | TestPoint:TestPoint_Pad_1.0x1.0mm | Boot |
| 1 | BOOT | Button_Switch_SMD:SW_SPST_TL3342 | SW1 |
| 1 | BZT52B3V3 | Diode_SMD:D_SOD-123F | D3 |
| 1 | BZT52Bxx | Diode_SMD:D_SOD-123F | D4 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | FLASH_NRST | TestPoint:TestPoint_Pad_1.0x1.0mm | FlashNRST |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | MCP73831 | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | MX25R3235FM1IL0 | Package_SO:JEITA_SOIC-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | NRST | TestPoint:TestPoint_Pad_1.0x1.0mm | NRST |
| 1 | SCL | TestPoint:TestPoint_Pad_1.0x1.0mm | SCL |
| 1 | SDA | TestPoint:TestPoint_Pad_1.0x1.0mm | SDA |
| 1 | STM32L072CBT6 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | SWCLK | TestPoint:TestPoint_Pad_1.0x1.0mm | SWC |
| 1 | SWDIO | TestPoint:TestPoint_Pad_1.0x1.0mm | SWD |
| 1 | USB_A | Connector_USB_PCB_Edge:USB_A_PCB_Edge_receptacle | J1 |
| 1 | VDD | TestPoint:TestPoint_Pad_1.0x1.0mm | 3v3 |
| 1 | VSS | TestPoint:TestPoint_Pad_1.0x1.0mm | G |
| 1 | XC6206P332MR | Package_TO_SOT_SMD:SOT-23-3 | U6 |
The 45 most common of 48 parts.
Similar boards
- 4 layers52.8 × 47 mm

- 2 layers76 × 56 mm

Ai sdr mini
HaohanHe/MBDSDR
AI-driven SDR & VNA system: LLM-callable tools over MCP with human-approval gates (C++/Qt6 + Python + Flutter)
62 partsMIT - 6 layers102.6 × 62.6 mm

- 4 layers30 × 51 mm

Launch relay
NCSU-High-Powered-Rocketry-Club/Launch-Relay-KiCAD
KiCAD files for the rocket launch detection relay board
68 partsMIT - 4 layers68 × 44 mm

- 2 layers42 × 54 mm

Click counter Q5
dudgeon/count-fidget
A lightweight, rechargeable two-key fidget that counts clicks, resets with a second key, and remembers its count while asleep or unpowered. Designed for a home-printed enclosure and professionally assembled electronics.
96 parts - 4 layers89 × 137 mm

- 4 layers51.6 × 56 mm

LoRa STM32 Board
collins-emasi/KiCAD-PROJECTS-PCB
In this repository, I will be sharing some of the project I'm working on with KiCAD software.
85 parts1
Questions
How big is the Titania3 PCB?
It measures 16.4 × 48.7 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Titania3 use?
48 parts, built around the STM32L072CBT6, BMP580, MX25R3235FM1IL0 and BMI260. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Titania3 KiCad files?
From the Danzibob/Titania3 repository on GitHub, at the commit this page was made from: the board is hardware/kicad_project/Titania3.kicad_pcb and its schematic hardware/kicad_project/Titania3.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Titania3 design in my own project?
Its repository states no licence, so its author keeps all rights: ask Danzibob before reusing the design.