Skip to the content
2 layers91.3 × 67 mmVGABreakout, the printed circuit board in 3D

A collection of glitch art circuits dedicated to VGA signal manipulation

Size
91.3 × 67 mm
Copper layers
2
Thickness
1.6 mm
Parts
12
Nets
17
Pads
64
Tracks, vias
152, 4
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
29 Aug 2019
Updated
9 Feb 2020

Overview

VGABreakout is an open-source printed circuit board by CTXz, from the CTXz/Video-Glitch-Array repository on GitHub. It is a 2-layer board of 91.3 × 67 mm with 12 parts on 17 nets, routed with 152 tracks and 4 vias.

Its parts include 6 switches and 5 connectors.

README

PixelSlasher/README.md

VGA Pixel Slasher

NOTE: This board is still in its early stages and may contain errors or perform sub-optimally. It is subject to major changes in the future.

Board Showcase

An assembled Pixel Slasher rev 1.0 board which is still missing the CV input and has a few quirky labeling errors

The Video Glitch Array Pixel Slasher is a device which delivers some seriously interesting glitch artifacts by cutting off color signals that exceed a specific brightness.

Showcase

Unprocessed Glitch piece from my tribute to the Hong Kong protests: No longer fiction.

Showcase1

Photography credit: Anthony Wallace


Just another glitched sad mac

Showcase3


Pixel slasher glitching webcam video output

Showcase2

Operation

The Video Glitch Array Pixel Slasher operates by using LM393 comparators to pull down color signals as soon as they exceed a certain voltage threshold, or in other words, a brightness threshold. The voltage thresholds for each color signal can be either set using slide potentiometers, or a 0-0.7V CV signal. Switching between the potentiometers and the CV input is simply a matter of flipping a switch.

Due to the fact that the non-inverting comparator input is tied to the color signal which is also being pulled down by a generic BC337 NPN transistor driven by the LM393 comparator output, an oscillation occurs. This in combination with the rather slow response time of the LM393 induces "wavy" repeating patterns across areas that exceed the threshold voltage, which take shape according to what's projected on the display.

Since the device operates by pulling down the VGA color signals, the color signals are connected in parallel to VGA wire. Thus, to set up the pixel slasher, simply connect the 5V and GND pins to the 5V and GND pins of your VGA cable or breakout board, and connect the color signal inputs in parallel to the VGA color wires.

If you're using the Video Glitch Array Breakout Board, setting up the pixel slasher is just a matter of closing all switches, and connecting the breakout board outputs to the appropriate pixel slasher inputs.

Prototype Board

First Pixel Slasher prototype board

Schematic

Schematic

You can download the Schematic for the VGA Pixel Slasher here. Alternatively you can import this board into KiCad and browse the schematic there.

PCB

PCB

J2, J3 and J4 provide a CV input for each color signal

Files

All KiCad PCB files, as well as gerbers can be found in this directory. To order the PCB, simply grab the grab the gerbers from the Gerbers directory and send them to your preferred PCB manufacturer.

Components

The following table provides a list of the necessary components along with links to some examples. It is highly recommended to do a little research yourself here. Chances are that your local hardware store might be selling some components a lot cheaper.

ComponentRefQuantityExamplesNotes/Tips
1x5 2.54mm Female HeadersJ11https://www2.mouser.com/ProductDetail/Molex/90147-1105?qs=sGAEpiMZZMs%252BGHln7q6pm8uos17B4BQAKRARw53BRV0%3DShould you already have larger 2.54mm Female headers lying around, you could easily cut those instead of buying new ones
1x1 2.54mm Female HeaderJ2, J3, J43Not available, must be cutAs 1x1 female headers aren't available commercially, they must be cut. Alternatively you can use male pin headers instead
4.7mm Spacing SPST or SPDT Slide SwitchSW1, SW2, SW33https://www.amazon.com/SS12D10-Straight-Spacing-SS12D10G5-Vertical/dp/B07SJPN2HM/ref=sr_1_1?keywords=4.7mm+spacing+slide+switch&qid=1569413333&s=gateway&sr=8-1Should these become too pricey, feel free to edit the PCB in KiCad to fit a different switch
LM393 DIP-8U1, U22https://www.mouser.de/ProductDetail/Texas-Instruments/LM393P?qs=sGAEpiMZZMuayl%2FEk2kXcddlv8%252BlGbVFYZWyaRldvtc%3DThese will almost certainly be available for dirt cheap at your local hardware store. Any DIP8 version will do (LM393P, LM393NG, etc.). If you would like to reuse the LM393 chips later on, it may be desired to use DIP-8 sockets.
BC337 TO-92 (ideally straight lead)Q1, Q2, Q33https://www.mouser.de/ProductDetail/Taiwan-Semiconductor/BC337-40-A1?qs=sGAEpiMZZMshyDBzk1%2FWiwIK8FF8XsC1RNbmjp0kCPo%3DThese will almost certainly be available for dirt cheap at your local hardware store. Bent lead packages will require a little force to insert trough.
10k, 60mm length, 45mm travel, 9mm width, linear slide potentiometersRV1, RV2, RV33https://www.mouser.de/ProductDetail/Bourns/PTA4553-2010CIB103?qs=sGAEpiMZZMtC25l1F4XBU%252BN3R7ksrj06xuOmWpCZ94k%3D
3.3k ResistorsR2, R4, R63https://www.mouser.de/ProductDetail/Vishay-Beyschlag/MBB02070C8200FCT00?qs=LkqrmUh5PII6P3inXi6ZTw%3D%3D&vip=1&gclid=CjwKCAjwlovtBRBrEiwAG3XJ-xNsZWIVeUh_aOER6JCOpZIqBPNapCJ1sNui1su29KHtjrVvs_qh3RoCCVQQAvD_BwESince these are pull-up resistors, their resistances aren't critical. Thus any ordinary 1k to 10k resistor will do just fine as well.
51k resistorsR1, R3, R53https://www.mouser.de/ProductDetail/Yageo/MFR-25FTE52-51K?qs=sGAEpiMZZMu61qfTUdNhG0IXHLFuiNnd2ZOrYz8UKLE%3DThese should be as precise as possible. A too low resistance will shorten the practical potentiometer range. A too high resistance will cause effects to still appear even at the highest resistance.

Soldering

When soldering, I recommend to begin with the resistors first, as those are the smallest components. Then proceed with the female headers and transistors. Then solder in the LM393 chips, and last but not least, the switches and the slide pots.

Soldering the transistors leads can be a little difficult due to the density of the pins. It's highly recommended to have soldering braid/wick at your hand. In future revisions it is planned to increase the size of the transistor footprints.

License

The VGA Pixel Slasher is licensed under the TAPR Open Hardware License v1.0 (See https://www.tapr.org/ohl.html)

Parts

12
QtyValueFootprintReferences
6SW_SPSTVGABreakout:255SBSW1, SW2, SW3, SW4, SW5, SW6
2Conn_01x05_FemaleConnector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_VerticalJ3, J4
2DB15_Female_HighDensityConnector_Dsub:DSUB-15-HD_Female_Horizontal_P2.29x1.98mm_EdgePinOffset8.35mm_Housed_MountingHolesOffset10.89mmJ1, J5
1Conn_01x02_FemaleConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ2

The 11 most common of 12 parts.

More from CTXz/Video-Glitch-Array

1
  • 2 layers52.8 × 149.3 mmPixelSlasher, the printed circuit board in 3D

    PixelSlasher

    CTXz/Video-Glitch-Array

    A collection of glitch art circuits dedicated to VGA signal manipulation

    22 parts30

Similar boards

  • 2 layersNrf bga, the printed circuit board in 3D

    Nrf bga

    github-linguist/linguist

    Language Savant. If your repository's language is being reported incorrectly, send us a pull request!

    12 parts14kMIT
  • 2 layers66.9 × 74.5 mmDeskHop, the printed circuit board in 3D

    DeskHop

    hrvach/deskhop

    Fast Desktop Switching Device

    12 parts7.9kGPL-3.0
  • 2 layers40 × 15 mmSensors, the printed circuit board in 3D

    Sensors

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    12 parts3kApache-2.0
  • 2 layers42.7 × 56.5 mmTle6240 driver, the printed circuit board in 3D

    Tle6240 driver

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    12 parts1.2k
  • 2 layers49 × 25 mm5v boost regulator, the printed circuit board in 3D

    5v boost regulator

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    12 parts915
  • 2 layers28.3 × 10.3 mmTap Photosensor PCB, the printed circuit board in 3D

    Tap Photosensor PCB

    VoronDesign/Voron-Tap

    Tap is a nozzle-based z-probe for the V2 and Trident printer designs. The entire toolhead moves to trigger an optical switch. Tap offers many advantages:

    12 parts716GPL-3.0
  • 2 layers25.4 × 70.4 mmTpmsniffer, the printed circuit board in 3D

    Tpmsniffer

    stacksmashing/pico-tpmsniffer

    A simple, very experimental TPM sniffer for LPC bus

    12 parts696

Questions

How big is the VGABreakout PCB?

It measures 91.3 × 67 mm and has 2 copper layers, 1.6 mm thick.

What parts does the VGABreakout use?

12 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the VGABreakout KiCad files?

From the CTXz/Video-Glitch-Array repository on GitHub, at the commit this page was made from: the board is VGABreakout/VGABreakout.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the VGABreakout design in my own project?

Its repository states no licence, so its author keeps all rights: ask CTXz before reusing the design.