Skip to the content
2 layers55.5 × 33.7 mmDMX Subboard, the printed circuit board in 3D

A simple four port USB-DMX ArtNET-Node

Size
55.5 × 33.7 mm
Copper layers
2
Thickness
1.6 mm
Parts
11
Nets
11
Pads
47
Tracks, vias
93, 3
Pours
2
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
6 Nov 2022
Updated
14 Oct 2026

Overview

DMX Subboard is an open-source printed circuit board by CShark, from the CShark/Lumen-ArtNode repository on GitHub. It is a 2-layer board of 55.5 × 33.7 mm with 11 parts on 11 nets, routed with 93 tracks and 3 vias.

Its parts include 4 switches, 2 resistors and 2 connectors. It belongs with the interfaces and adapters boards and the STM32 boards of this library.

README

README.md

USB ArtNET Interface

This project is a USB ArtNET interface with four ports, based on the STM32G484. It will register itself as an Ethernet Card using the CDC-NCM protocoll to be automatically recognized by most operating systems (except Windows 10, which needs some manual configuration). It will then bind the ArtNET-implementation to a configurable IP on that virtual ethernet card. The device can be configured either using ArtNET commands for software that supports this, using a web interface on the device and it can optionally be extended to include a display module for configuration directly at the device.

Schematic

The project uses an STM32G484RE, but should work with any STM32G4xxRE variant. The ports are controlled by a MAX3440E each, which will provide some ESD protection in addition to the TVS-Diodes. The device will draw around ~150mA, which is easily delivered by USB2.0 ports. Galvanic isolation was omitted because it needs too much space and because it is not recommended for the transmitting ports of DMX-Devices anyway (although it is recommended for receiving ports, but not mandatory).

PCB

The PCB is designed as a four layer board, as with this small size the price was acceptable. The pcb was designed with a TEKAL 31.29-case from TEKO in mind, but any case with at least 100x100mm will work. placing three ports at the rear and one port beside the usb port at the front of the case. The display module is completely optional and is designed to slot into the mainboard and is secured with an additional screw from the front. It is then connected using a 10-pin ribbon cable.

BOM

The total cost for this device is currently aproximately 90€. Assembly takes around 6 hours, including soldering the boards, CNC the covers and soldering / crimping the connectors. You can save money by printing your own case (25€), finding a cheaper STM32G4xxRE variant at your local dealer (11€), finding cheaper XLR connectors (5€) and skipping on the display module (5€).

Mainboard (~40€)
AmountTypeValueFootprint
4Capacitor1μF0603
7Capacitor100nF0603
2Capacitor20pF0603
1Capacitor10nF0603
1Capacitor4.7μF0603
8TVS DiodeSMA
1USB-C Receptacle
1FFC Connector1x10, Pitch 1mm
4Terminal Block1x3, Pitch 2.54mm
1Pin Header1x3, Pitch 2.54mm
1Jumper1x2, Pitch 2.54mm
2Resistor5K10603
1Resistor4K70603
4Resistor1300603
8Resistor5600603
1SwitchThrough Hole, Height 6mm
1SwitchThrough Hole, Angled, Height 6mm
1DIP-SwitchThrough Hole, 2x4, Pitch 2.54mm
1ESD ProtectionESDALD05UD4SOT23-6
1Linear RegulatorAP2112K-3.3SOT23-5
4TransceiverMAX3440ESOIC-8
1Crystal25MHzHC49
1μCSTM32G484RELQFP64
Display Board (~5€)
AmountTypeFootprint
1OLED-Display0.96" with I²C and SSD1306 compatible driver
1FFC Connector1x10, Pitch 1mm
2Resistor4K7
4SwitchThrough Hole, Height 10mm
1FFC Cable1x10, Pitch 1mm, Length ~100mm, Type B (opposing-side contacts)
Mechanical parts (~40€)
AmountTypeSpecs
1CaseTEKO TEKAL 31.29, or any case that takes Eurocard-sized PCBs (100x100mm)
4XLR ConnectorAn individual mix of Female and Male XLR 3- and 5-Pin connectors, depending on your needs
9ScrewsM2, Length 15mm, Countersink
9NutsM2
1Acrylic Window15mm x 25mm
1SpacerM2, Length 6mm
1Mainboard PCB
1Display PCB

Here are two lists on digikey that include all necessary components, except for the mechanical parts and the oled-display. It does contain four XLR-Connectors though.

Firmware

The firmware is completely custom, only based on CMSIS (no HAL) and supports the important parts of the ArtNET protocol. Which port is an input and which an output can be set using the dip switches, but later be overwritten using either ArtNET commands, the WebUI or the display menu. The device also has a reset button to reset the configuration for when things go completely wrong. If the device is completely bricked it can be put into bootloader mode using a jumper on the mainboard.

The device supports mDNS and is always reachable using artnet.local in addition to its ip-address. The WebUI allows configuring each individual port with all the settings that ArtNET-Commands also support. You can also change the ip-configuration of the device and its internal minimal DHCP-Server, as well as clearing all settings, rebooting the device and switching the device into DFU/Bootloader mode to flash a new firmware.

Parts

11
QtyValueFootprintReferences
24K7Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR1, R2
1BackButton_Switch_THT:SW_PUSH_6mm_H8.5mmSW1
1ConfirmButton_Switch_THT:SW_PUSH_6mm_H8.5mmSW4
1ConnectorConnector_FFC-FPC:TE_1-84952-0_1x10-1MP_P1.0mm_HorizontalJ2
1DownButton_Switch_THT:SW_PUSH_6mm_H8.5mmSW3
1OLEDConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ1
1PIN 1Jumper:SolderJumper-3_P2.0mm_Open_TrianglePad1.0x1.5mmJP1
1PIN 2Jumper:SolderJumper-3_P2.0mm_Open_TrianglePad1.0x1.5mmJP2
1UpButton_Switch_THT:SW_PUSH_6mm_H8.5mmSW2

The 10 most common of 11 parts.

More from CShark/Lumen-ArtNode

1
  • 4 layers100 × 52.3 mmDMX, the printed circuit board in 3D

    DMX

    CShark/Lumen-ArtNode

    A simple four port USB-DMX ArtNET-Node

    61 parts24

Similar boards

  • 2 layers60 × 30 mmController, the printed circuit board in 3D

    Controller

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    11 parts3kApache-2.0
  • 2 layers103 × 30.5 mmTS Front Endcap, the printed circuit board in 3D

    TS Front Endcap

    EEVengers/ThunderScope

    ThunderScope GitHub Repo

    11 parts1.3kMIT
  • 2 layers26 × 30 mmExpansion Card, the printed circuit board in 3D

    Expansion Card

    FrameworkComputer/ExpansionCards

    Reference designs and documentation to create Expansion Cards for the Framework Laptop

    11 parts1.1kCC-BY-4.0
  • 2 layers53.9 × 23.2 mmBuffer, the printed circuit board in 3D

    Buffer

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    11 parts1kGPL-3.0
  • 2 layers10 × 20 mm2 connector Sensor Board, the printed circuit board in 3D

    2 connector Sensor Board

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    11 parts915
  • 2 layersFet module, the printed circuit board in 3D

    Fet module

    ByteWelder/Decktility

    A handheld PC

    11 parts855CC-BY-SA-4.0
  • 2 layers47 × 33 mmSevensegment led display module, the printed circuit board in 3D

    Sevensegment led display module

    tardate/LittleArduinoProjects

    a collection of "Little Electronic & Arduino Projects", most involving electronics or an Arduino in one way or another!

    11 parts803MIT
  • 2 layers42.5 × 36.8 mmDevboard, the printed circuit board in 3D

    Devboard

    basilfx/TRADFRI-Hacking

    Hacking IKEA TRÅDFRI products, such as light bulbs, window blinds and other accessories.

    11 parts743CC-BY-4.0

Questions

How big is the DMX Subboard PCB?

It measures 55.5 × 33.7 mm and has 2 copper layers, 1.6 mm thick.

What parts does the DMX Subboard use?

11 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the DMX Subboard KiCad files?

From the CShark/Lumen-ArtNode repository on GitHub, at the commit this page was made from: the board is hardware/schematic/Sub/DMX Subboard.kicad_pcb and its schematic hardware/schematic/Main/DMX.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the DMX Subboard design in my own project?

Its repository states no licence, so its author keeps all rights: ask CShark before reusing the design.