Skip to the content
2 layers76.2 × 92.3 mmNs disk k, the printed circuit board in 3D

NorthStar Advantage Hard Disk

Size
76.2 × 92.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
24
Nets
67
Pads
212
Tracks, vias
0, 0
Routed
Not yet
KiCad
KiCad 9.0 (file 20241229)
Created
17 Jun 2025
Updated
18 Jun 2025

Overview

Ns disk k is an open-source printed circuit board by csegura, from the csegura/nh_disk repository on GitHub. It is a 2-layer board of 76.2 × 92.3 mm with 24 parts on 67 nets.

It is built around the TXS0108EPW and AMS1117-3.3. Its parts include 4 capacitors, 4 resistors, 4 connectors, 3 ICs and 2 diodes. It belongs with the RP2040 boards of this library.

Main components

2

README

readme.md

NorthStar Advantage Hard Disk

This repository is made with the aim of completing a HardDisk Card for the NorthStar Advantage system.

The idea is use a microcontroller (pi pico) to emulate a disk drive, allowing the NorthStar Advantage to read and write to a disk image stored on an SD card.

This is an ambitious project, as the NorthStar Advantage system is quite old and has a unique architecture, but it is a fun challenge. I am an enthusiast of retro computing and I want to see if I can make this work. So any help will be welcome.

Outside sure there a lot of other enthusiasts that would like to see this project completed, so welcome to the project!

Current status

  • The project is in the early stages of development.

prototype

Pi pico plan (code)

Continuously monitor the /SELECT line (via PIO) when /SELECT is asserted (low); and monitor the primary I/O control: /BRD (I/O Read), /BWR (I/O Write), /IDREQ (Board ID Read).

Address decoding

Capture the lower I/O address bits (IOA0–IOA3) (IOA3 is not used in HD controller) from the bus when an active cycle is detected. Get the target register.

I/O reads

Upon detecting an I/O read cycle (/SELECT low and /BRD low):

  • Push the captured port address (IOA0–IOA3) to the PIO's RX FIFO to notify the CPU and push the captured port address to the CPU's RX FIFO.
  • Change the direction of the IOD0–IOD7 data lines to output while waiting for the CPU to write the requested data byte into the PIO's TX FIFO.
  • Once the TX FIFO contains data, unblock it and drive the byte onto the IOD0–IOD7 lines.
  • After /BRD goes high, change the direction of IOD0–IOD7 back to input (tristate).

I/O writes

Upon detecting an I/O write cycle (/SELECT low and /BWR low):

  • Ensure that the IOD0–IOD7 lines are configured as inputs.
  • Capture the port address (IOA0–IOA3) and push it to the RX FIFO.
  • Obtain the data byte present on the IOD0–IOD7 lines.
  • Push the data byte to the RX FIFO and notify the CPU.
  • Wait for the /BWR signal to be deasserted (go high).

Board ID

Upon detecting an ID Read cycle (/SELECT low AND /IDREQ low)

  • Push the relevant port address.

Once the CPU is informed take the actions read registers, read/write to sdcard.

References

Special thanks

  • Evan Allen for the inspiration and initial work on the NorthStar Advantage cards and help me with the project.

Parts

24
QtyValueFootprintReferences
2,
20.1ufCapacitor_Tantalum_SMD:CP_EIA-1608-08_AVX-J_HandSolderC1, C2
2LEDLED_SMD:LED_0402_1005MetricD1, D2
2TXS0108EPWPackage_SO:TSSOP-20_4.4x6.5mm_P0.65mmU1, U2
2gndConnector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_VerticalTP3, TP4
1+3.3vConnector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_VerticalTP1
1100ufCapacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-AC3
110kResistor_SMD:R_0603_1608MetricR3
1180Resistor_SMD:R_0805_2012MetricR1
12.2kResistor_SMD:R_0603_1608MetricR4
1220Resistor_SMD:R_0805_2012MetricR2
147ufCapacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-AC4
15vConnector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_VerticalTP2
1AMS1117-3.3Package_TO_SOT_SMD:SOT-223-3_TabPin2U3
1ButtonsConnector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_VerticalJ3
1MICRO-SD-CARD_project_library:MICROSDCARDJ4
1OLED DisplayConnector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_VerticalJ2
1RaspberryPi_Pico_WModule:RaspberryPi_Pico_Common_UnspecifiedA1
1northstar card edge_project_library:northstar edge connectorP1

Similar boards

  • 2 layers94.5 × 74.4 mmAx58100-stm32-ethercat, the printed circuit board in 3D

    Ax58100-stm32-ethercat

    MetalMusings/MyOwnEtherCATDevice

    Documentation accompanying the "Make My Own EtherCAT device" video serie on Youtube.

    184 parts93
  • 2 layers72 × 45 mmBrizer ZigBee, the printed circuit board in 3D

    Brizer ZigBee

    kvazimoda24/TionO2-ZigBee

    Ядром проекта является микроконтроллер ATmega328P. Для работы по протоколу ZigBee используется модуль E18-MS1-PCB.

    48 parts10
  • 2 layers67.3 × 74.5 mmVgm teensy, the printed circuit board in 3D

    Vgm teensy

    ldursw/vgm-player

    Hardware music player for YM2612 and SN76489

    41 parts7GPL-3.0
  • 2 layers100 × 50 mmEspled, the printed circuit board in 3D

    Espled

    Yottabits/espled

    THE one and only esp8266 LED Controller

    52 parts6
  • 2 layers190.5 × 158.4 mm68k dev, the printed circuit board in 3D

    68k dev

    maded2/68000

    68000 Retro computer with Amiga Chipset

    84 parts4Apache-2.0
  • 6 layers80 × 80 mmV2ultimateflightcomp, the printed circuit board in 3D

    V2ultimateflightcomp

    codinga593/IRIS

    A next generation model rocket focused on a precise propulsive landing on a tower.

    144 parts3
  • 2 layers55.8 × 28.6 mmNmea0183-i2c wifi, the printed circuit board in 3D

    Nmea0183-i2c wifi

    alexsomesan/nmea0183-i2c-wifi

    Reads wind data from a NASA Clipper wind instrument via I2C and sends out NMEA0183 wind messages via WiFi.

    14 parts1

Questions

How big is the Ns disk k PCB?

It measures 76.2 × 92.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Ns disk k use?

24 parts, built around the TXS0108EPW and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Ns disk k KiCad files?

From the csegura/nh_disk repository on GitHub, at the commit this page was made from: the board is pcb/ns_disk_k.kicad_pcb and its schematic pcb/ns_disk_k.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Ns disk k design in my own project?

Its repository states no licence, so its author keeps all rights: ask csegura before reusing the design.