Skip to the content
2 layers134.6 × 82.5 mmCryologger AWS, the printed circuit board in 3D

A low-cost automatic weather station based on the open-source Arduino platform.

Size
134.6 × 82.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
25
Nets
41
Pads
203
Tracks, vias
275, 66
Pours
2
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
18 Mar 2020
Updated
3 May 2024

Overview

Cryologger AWS is an open-source printed circuit board by cryologger, from the cryologger/automatic-weather-station repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 134.6 × 82.5 mm with 25 parts on 41 nets, routed with 275 tracks and 66 vias.

Its parts include 10 ICs, 4 resistors, 4 connectors and 1 capacitor. It belongs with the home automation and IoT and sensors and measurement boards of this library.

README

README.md

GitHub GitHub release (latest by date) GitHub issues

Cryologger - Automatic Weather Station (AWS)

Note: This project is under active development.

DSC_7941

1.0 Introduction

Polar environments are undergoing rapid environmental change, yet there is a lack of high spatial and temporal monitoring data available in these remote regions. Reliance on expensive and proprietary commercial data acquisition and telemetry systems can inhibit both researchers and citizen scientists and present a significant barrier to the establishment of widespread monitoring networks. The development of low-cost, open-source instrumentation can greatly reduce the cost of cryospheric research, improve the spatial density and coverage of collected data, and produce new ways to observe and monitor the cryosphere.

The Cryologger Automatic Weather Station (AWS), is an open-source datalogger and telemeter comprised of low-cost, off the shelf components that is capable of supporting the physical measurement needs of a variety of cryospheric scientific applications when configured as an automatic weather station (AWS).

2.0 Methods

2.1 Design

The Cryologger AWS is based on the open-source Arduino platform (www.arduino.cc) and built using low-cost, do-it-yourself electronics that can be easily modified to meet the needs of the end-user. Code was written using the Arduino Integrated Development Environment (IDE) and benefits from the availability of community-generated libraries.

Planned for extended deployments in harsh Arctic conditions, the Cryologger AWS provides long-term measurements of weather variables such as temperature, humidity, wind speed, wind direction, solar irradiance and snow depth, as well as system diagnostic variables including pitch, roll, battery voltage. Data are transmitted over the Iridium satellite network at specified intervals and can be remotely updated based on the desired sampling frequency. Collected data are made available in near-real time at https://cryologger.org.

2.1.1. Bill of Materials (BOM)

For a complete bill of materials, including requirements for power and mounting of a complete deployable system, please see ASSEMBLY.md.

Table 1. Bill of materials and associated costs for the main components used in the Cryologger AWS v1.0. Prices are listed in USD and are current as of December 2023. Taxes and shipping not included. 1Denotes optional component.

ComponentProductQuantityCost (USD)
PCBCustom Cryologger Printed Circuit Board1$5.00
Satellite transceiverRock7 RockBLOCK 96031$267.50
Satellite antennaMaxtena M1621HCT-P-SMA1$54.00
ProcessorAdafruit Feather M0 Adalogger1$19.95
GNSSAdafruit Ultimate GPS FeatherWing1$24.95
IMUAdafruit LSM303AGR Accelerometer Magnetometer1$12.50
SensorAdafruit BME280 Temperature Humidity Pressure Sensor 1$14.95
Voltage regulatorPololu D36V6F3 3.3V 600mA Step-Down Voltage Regulator1$16.95
Voltage regulatorPololu D36V6F5 5V 600mA Step-Down Voltage Regulator1$16.95
Voltage regulatorPololu U3V40F12 12V Step-Up Voltage Regulator 1$9.95
Resistor10 M 1% 0.6 W resistor1$0.44
Resistor1 M 1% 0.6 W resistor1$0.40
Capacitor0.1 uF Capacitor1$0.29
Power connector1
Power connector1
Connector1

Table 2. Environmental sensors used in Cryologger AWS v1.0. Prices are listed in USD and are current as of December 2023. Taxes and shipping not included.

Environment VariableSensorCost (USD)
Wind Speed & DirectionRM Young Wind Monitor 5103L Anemometer$1432
Temperature/Relative HumidityVaisala HMP60 Humidity and Temperature Probe$330
Solar IrradianceSP-212-SS: Amplified 0-2.5 Volt Pyranometer$325
Snow DepthMaxboxtix MB7374 HRXL-MaxSonar-WRST7$290

2.2 Operation

When initially powered on, the Cryologger AWS will attempt to establish a GNSS fix and sychronize the real-time clock (RTC) for up to 5 minutes. Once the RTC is synchronized, the system will set an alarm to wake at the user-specified time and then enter a low-power deep sleep. Nominally, the system will wake every 5 minutes, obtain measurements from all sensors, and log data to a microSD card. Measurements are averaged each hour and transmitted

While the system is in deep sleep, a Watchdog Timer (WDT) will wake the system to check the program has not frozen every 8 seconds and perform a reset, if necessary. This helps to ensure the long-term reliability of the system.

2.2.1 Measurements

Table 2. List of Cryologger AWS v1.0 data variables that can be transmitted and/or logged with variable sizes.

TypeVariableDescriptionSize (bytes)
uint32_tunixtimeUNIX Epoch time4
int16_ttemperatureIntInternal temperature (°C)2
uint16_thumidityIntInternal humidity (%)2
uint16_tpressureIntInternal pressure (hPa)2
int16_ttemperatureExtExternal temperature (°C)2
uint16_thumidityExtExternal humidity (%)2
int16_tpitchPitch (°)2
int16_trollRoll (°)2
uint16_tsolarSolar irradiance (W m-2)2
uint16_twindSpeedMean wind speed (m/s)2
uint16_twindDirectionMean wind direction (°)2
uint16_twindGustSpeedWind gust speed (m/s)2
uint16_twindGustDirectionWind gust direction (°)2
int32_tlatitudeLatitude (DD)4
int32_tlongitudeLongitude (DD)4
uint8_tsatellitesNumber of satellites1
uint16_thdopHDOP2
uint16_tvoltageBattery voltage (V)2
uint16_ttransmitDurationPrevious transmission duration (s)2
uint8_ttransmitStatusIridium return code1
uint16_titerationCounterMessage counter2
2.2.2 Data Transmission and Processing

Sensor measurements and GNSS position are recorded hourly and stored in memory until the desired transmission interval is reached. Data are compressed into a binary message (340 bytes maximum) to minimize the cost and total number of transmissions required. Data are transmitted via the Iridium Short Burst Data (SBD) satellite network at user-specified intervals, which can be remotely updated based on the desired sampling frequency. SBD data messages are received by an Iridium ground station and sent to Ground Control's server. The data is then forwarded to an Amazon Web Services (AWS) SQS queue, decoded using an AWS Lambda Python function and stored in a database using the Amazon Relational Database Service (RDS). Data can be viewed in near-real time at https://cryologger.org.

3.0 Deployments

Figure 3. Map of Cryologger AWS deployments made between 2019 and 2023.

4.0 Results

5.0 Conclusion

Repository Contents

  • /Documentation - Assembly, deployment and troubleshoting guides, as well as information of components used and associated costs.

  • /Hardware - KiCad PCB schematic and design files.

  • /Software - Arduino code and Python data analysis scripts.

License Information

Cryologger code, firmware, and software is licensed under the GNU General Public License v3.0 (https://www.gnu.org/licenses/gpl-3.0.en.html).

Cryologger hardware is licensed under CC BY-NC-SA 4.0

Cheers,

Adam

Parts

25
QtyValueFootprintReferences
4MountingHole_PadMountingHole:MountingHole_3mm_PadH1, H2, H3, H4
3Pololu_D36V6Cryologger:Pololu D36V6xU6, U7, U10
3Screw_Terminal_01x04Connector_Phoenix_MSTB:PhoenixContact_MSTBA_2,5_4-G-5,08_1x04_P5.08mm_HorizontalJ2, J3, J4
2150Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR3, R4
2Adafruit_Feather_HeaderCryologger:Adafruit_Feather_Header_DoubleU3, U4
11MResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR2
14MResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1
1Adafruit_DPS310Cryologger:Adafruit_DPS310U2
1Adafruit_LSM303AGRCryologger:Adafruit_LSM303AGRU1
1CCapacitor_THT:C_Disc_D3.8mm_W2.6mm_P2.50mmC1
1ROCKBLOCK_9603Connector_Molex:Molex_PicoBlade_53047-1010_1x10_P1.25mm_VerticalU5
1RockBLOCK_FootprintCryologger:RockBLOCK_9603_FootprintU8
1Screw_Terminal_01x02Connector_Phoenix_MSTB:PhoenixContact_MSTBA_2,5_2-G-5,08_1x02_P5.08mm_HorizontalJ1
1U3V40FxCryologger:Pololu U3V40FxU9

The 23 most common of 25 parts.

More from cryologger/automatic-weather-station

3
  • 2 layers133.4 × 79.4 mmCryologger AWS, the printed circuit board in 3D

    Cryologger AWS

    cryologger/automatic-weather-station

    A low-cost automatic weather station based on the open-source Arduino platform.

    24 parts16GPL-3.0
  • 2 layers133.4 × 79.4 mmCryologger AWS, the printed circuit board in 3D

    Cryologger AWS

    cryologger/automatic-weather-station

    A low-cost automatic weather station based on the open-source Arduino platform.

    22 parts16GPL-3.0
  • 2 layers134.6 × 82.5 mmCryologger AWS, the printed circuit board in 3D

    Cryologger AWS

    cryologger/automatic-weather-station

    A low-cost automatic weather station based on the open-source Arduino platform.

    21 parts16GPL-3.0

Similar boards

  • 2 layers159.5 × 30 mmType f, the printed circuit board in 3D

    Type f

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    25 parts3kApache-2.0
  • 2 layers113.5 × 95.1 mmSweep high, the printed circuit board in 3D

    Sweep high

    davidphilipbarr/Sweep

    Sweep - a small promicro based keyboard inspired by the Ferris.

    25 parts2.1k
  • 2 layers58.4 × 114.3 mmPicoPedal, the printed circuit board in 3D

    PicoPedal

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    25 parts915
  • 2 layers54 × 15 mmXyp gpib, the printed circuit board in 3D

    Xyp gpib

    xyphro/UsbGpib

    Versatile, cheap and portable USB to GPIB converter (USBTMC class based)

    25 parts690MIT
  • 2 layers50 × 76 mmVoron 0, the printed circuit board in 3D

    Voron 0

    dennisss/dacha

    Monorepo for awesome tools/projects/libraries

    25 parts397Apache-2.0
  • 2 layers237.5 × 102.9 mmStorage, the printed circuit board in 3D

    Storage

    jes/scamp-cpu

    A homebrew 16-bit CPU with a homebrew Unix-like-ish operating system.

    25 parts301Unlicense
  • 2 layers43.3 × 21 mmNanoS3 Carrier, the printed circuit board in 3D

    NanoS3 Carrier

    UnexpectedMaker/esp32s3

    Assorted files for my ESP32-S3 development boards

    25 parts296

Questions

How big is the Cryologger AWS PCB?

It measures 134.6 × 82.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Cryologger AWS use?

25 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Cryologger AWS KiCad files?

From the cryologger/automatic-weather-station repository on GitHub, at the commit this page was made from: the board is Hardware/KiCad/Archived/v0.1/Cryologger AWS.kicad_pcb and its schematic Hardware/KiCad/Archived/v0.1/Cryologger AWS.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Cryologger AWS design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).