Skip to the content
2 layers99.9 × 64 mmMsx eeprom, the printed circuit board in 3D

A MSX 32K EEPROM AT28C256 cartridge rewritable by software.

Size
99.9 × 64 mm
Copper layers
2
Thickness
1.6 mm
Parts
99
Nets
49
Pads
454
Tracks, vias
278, 28
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
26 Jun 2020
Updated
20 May 2024

Overview

Msx eeprom is an open-source printed circuit board by costarc, from the costarc/msxcart_flash32k repository on GitHub, published under the MIT licence. It is a 2-layer board of 99.9 × 64 mm with 99 parts on 49 nets, routed with 278 tracks and 28 vias.

It is built around the AT28C256-15PU. Its parts include 2 capacitors, 2 connectors, 1 resistor and 1 IC. It belongs with the retro computing and games boards of this library.

Main components

1

README

README.md

msxcart_flash32k

MSX 32K EEPROM cartridge rewritable by software.

This project contain a schematic and a software for MSX computers. The schematic is a design to allow writing and reading the AT28C256 EEPROM (EEPROM = Electronically Rewritable Read Access Memory).

Note on the code to write the EEPROM:

Due to some technical problems to enable/disable the EEPROM Software Data Protecion (SDP), the auto detection only works if the SDP was previously disabled. Make sure the EEPROM SDP has not been enabled by other means, as for example, using an external EPROM programmer.

The programmer need the slot number where the EEPROM is inserted. You may need to guess the slot (usually it will be 1 or 2), but for EEPROMs that were previously programmed, it will be displayed using the command:

at28c256.com /i

Note that the slot 1 may not be the top slot in some MSXs. For example, the Canon V-25 slot 1 in on the bottom left side of the micro.

How to write a ROM to the EEPROM:

PCB Revision 1

  1. Close jumpers WR, A15, CS12. All others must be Open
  2. Boot the MSX
  3. Now close also jumper SLTSL (top jumper)
  4. Try to identify the slot where the cartridge is connected with parameter "/i". See Note 1 below.
  5. Write the ROM passing the correct slot number in the "/s" parameter, for example: at28c256 /s 1 /f roadfighter.rom)

PCB Revision 0 (with 6 jumpers):

  1. Close jumpers WR, A15. All others must be Open
  2. Boot the MSX
  3. Now close also jumper CS12
  4. Try to identify the slot where the cartridge is connected with parameter "/i". See Note 1 below.
  5. Write the ROM passing the correct slot number in the "/s" parameter, for example: at28c256 /s 1 /f roadfighter.rom)

PCB Revision 0 with an extra jumper wired up for SLTSL: Use the same steps described for Revison 1 above.

Boot from the EEPROM

To boot from the cart, just reboot the MSX. If you burned 2 ROMs, you can switch between them by moving the jumper between A15 and A14.

Notes:

1: Use "at28c256 /i" to check if the EEPROM slot can be located. If there was a previous ROM in the EEPROM, it will be identified and shown with the initial bytes "41 42". Note that all other internal expanded slots with some ROM will also be displayed, but with high slot numbers. If there was not any ROM previously recorded in your EEPROM, you may need to guess the slot number.

2: The external MSX slots will usually be identified by low numbers such as 01 and 02. Try using parameters "/s 1" or "/s 2" with the at28c256 command to program the EEPROM in these cases where the EEPROM is not located and you have to guess the slot number.

3: Do not remove jumper WR. It should be closed at all times. Write protect is enabled by software by the at28c256.com program.

4: To by-pass the cartridge ROM when it is connected in a slot, remove jumper SLTSL (Revision 1) or CS12 in Revision 0. Insert the jumper back on once the MSX has booted, otherwise the EEPROM will not be enabled for MSX to program it.

Parts

99
QtyValueFootprintReferences
91_Connector_Wire:SolderWirePad_2x02_P2.54mm_Drill0.8mm_, _, _, _, _, _, _, _, _, _, _, _, _, _, _, _ +75
1100nFCapacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mmC1
1100uFCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC2
110KResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1
1AT28C256-15PUMyFootprints:DIP254P1524X482-28U1
1Conn_02x07_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_HorizontalJ1
1LOGOMyFootprints:msx_msx2_msx+logoG***
1LOGOMyFootprints:msxlogoG***
1MSX_CONNECTORRoni Footprints:MSX_CART_SW_Official_3HolesP1

Similar boards

  • 4 layers101.6 × 76.2 mm8051dumper, the printed circuit board in 3D

    8051dumper

    JohnDMcMaster/8051dumper

    by NF6X. Forked from: https://gitlab.com/NF6X_Retrocomputing/8051dumper

    41 parts27
  • 2 layers40.6 × 68.6 mmEeprom programmer, the printed circuit board in 3D

    Eeprom programmer

    yoppeh/eeprom-programmer

    An Arduino Nano sketch and schematic for an Atmel 28cx programmer.

    7 parts10MIT
  • 4 layers100 × 100 mmRosco 6502, the printed circuit board in 3D

    Rosco 6502

    rosco-6502/rosco_6502

    Design, documentation and software for the Really Old School Computer (6502)

    62 parts8MIT
  • 2 layers99.5 × 70 mmZed-80, the printed circuit board in 3D

    Zed-80

    Gnardisitor/zed-80

    Simple Z80 computer based on Grant Searle's Z80 computer.

    33 parts
  • 2 layers99 × 96.5 mm6502-pactvm v01, the printed circuit board in 3D

    6502-pactvm v01

    napicella/8-bit-computer

    Resources for an 8 bit computer based on the 6502 micro processor

    15 parts
  • 4 layers160 × 100 mmRosco m68k, the printed circuit board in 3D

    Rosco m68k

    rosco-m68k/rosco_m68k

    Design, documentation and software for the Really Old School Computer (M68K)

    84 parts200
  • 2 layers116.8 × 147.3 mmCpu, the printed circuit board in 3D

    Cpu

    eshazen/retro-25

    Retro-tech HP-25 calculator clone using Z80

    52 parts33
  • 4 layers167.7 × 111.2 mmBB816-PCIE BANKZERO, the printed circuit board in 3D

    BB816-PCIE BANKZERO

    Aronnax9000/BB816-MATX-PCIE

    ATX form factor motherboard for Adrien Kohlbecker's BB816 CPU breakout board (rev. A27)

    16 parts2

Questions

How big is the Msx eeprom PCB?

It measures 99.9 × 64 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Msx eeprom use?

99 parts, built around the AT28C256-15PU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Msx eeprom KiCad files?

From the costarc/msxcart_flash32k repository on GitHub, at the commit this page was made from: the board is hardware/msx_eeprom.kicad_pcb and its schematic hardware/msx_eeprom.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Msx eeprom design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).