Skip to the content
2 layers26 × 16.5 mmPiezo preamp dual, the printed circuit board in 3D

High impedance preamplifier for piezo pickups

Size
26 × 16.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
31
Nets
17
Pads
73
Tracks, vias
157, 10
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
25 Dec 2023
Updated
1 Apr 2025

Overview

Piezo preamp dual is an open-source printed circuit board by compuphase, from the compuphase/piezo-preamplifier repository on GitHub. It is a 2-layer board of 26 × 16.5 mm with 31 parts on 17 nets, routed with 157 tracks and 10 vias.

Its parts include 18 capacitors, 6 resistors, 3 ICs and 3 connectors. It belongs with the audio and music boards of this library.

README

README.md

Piezo Pickup Preamplifier

These are simple designs for high impedance preamplifiers. They are intended for piezo pickups, and in particular for piezo bridge pickups for (nylon-stringed) guitars. There is a single-channel and a dual-channel design.

The designs are in KiCad. PDFs with the schematics, and the Gerber files for the PCBs are also provided.

Single channel

This circuit was built for use with a Shadow SH097 bridge pickup. The pickup has a capacitance of 680pF. Yet, input impedance of this preamplifier is only 1MΩ, because the basses were already quite pronounced.

It is a pretty classic opamp circuit. Amplification is fixed at 1× —the circuit is only to adapt the impedance (piezo bridge pickups are pretty loud already). The main feature of the circuit is that it is compact, and especially narrow. The idea is to fit this preamplifier into a slot immediately below the pickup.

The PDF with the schematic also shows the wiring for a TRS socket and battery; these are not on the PCB, and technically not part of the circuit). The main idea of the wiring is that the battery is connected only when the jack plug is inserted. When the plug is pulled out of the instrument, the battery is disconnected.

Dual channel

This circuit was built for the ARTEC PG-333 bridge pickup. The pickup connects two piezo bridge pickups in parallel, where each pickup covers only three strings. For use with this preamplifier, the two piezo segments have to be separated, and each connected to a separate input of the preamplifer. Input impedance for each channel is roughly 2MΩ.

I measured one of the piezo segments to have a capacitance of 580pF and the other as 970pF —to my surprise. This being the case, you will want to position the 580pF segment at the treble side, and the 970pF segment at the bass side of the bridge.

The dual-channel circuit has two independent impedance converters, and a third preamplifier to mix the outputs of the first stages. The balance of the "treble" side relative to the "bass" side, can be adjusted with a trimmer pot.

The preamplifier has a "bass boost" filter that boosts the frequencies below roughly 250 Hz by roughly 5 dB. The resonance chamber of a classical guitar has a main resonant frequency at around 200 to 250 Hz, which is what the bass boost emulates.


Copyright 2023-2025, CompuPhase, Thiadmer Riemersma
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License (https://creativecommons.org/licenses/by-nc-sa/4.0/).

Parts

31
QtyValueFootprintReferences
10100kVisualPlace:0603C9, C10, R3, R4, R5, R6, R10, R11, R12, R15
3220nVisualPlace:0603C1, C2, C5
3OPA323VisualPlace:SOT353U1, U2, U3
222kVisualPlace:0603R9, R13
22M2VisualPlace:0603R1, R2
2470kVisualPlace:0603R7, R8
268pVisualPlace:0603C3, C4
2piezoConnector_PinHeader_2.00mm:PinHeader_1x02_P2.00mm_VerticalJ3, J4
11uVisualPlace:0603C7
120kTrimPots:TC42RV2
122nVisualPlace:0603C6
14u7VisualPlace:0805C8
1outputConnector_PinHeader_2.00mm:PinHeader_1x03_P2.00mm_VerticalJ5

More from compuphase/piezo-preamplifier

1
  • 2 layers32 × 4 mmPiezo preamp single, the printed circuit board in 3D

    Piezo preamp single

    compuphase/piezo-preamplifier

    High impedance preamplifier for piezo pickups

    12 parts3

Similar boards

  • 2 layers44.5 × 46.9 mmOSO SWAT B1-jig, the printed circuit board in 3D

    OSO SWAT B1-jig

    joeycastillo/Sensor-Watch

    A board replacement for the classic Casio F-91W wristwatch

    31 parts2.1k
  • 2 layers65 × 30 mmRgb to hdmi, the printed circuit board in 3D

    Rgb to hdmi

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    31 parts1kGPL-3.0
  • 2 layers191 × 98.5 mmMacroKeypad, the printed circuit board in 3D

    MacroKeypad

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    31 parts915
  • 2 layers39 × 45.2 mmCH32V003F4P6-R0-1v1, the printed circuit board in 3D

    CH32V003F4P6-R0-1v1

    openwch/ch32v003

    CH32V003 is an ultra-cheap RISC-V MCU with 2KB SRAM, 16KB flash, and up to 18 GPIOs that sells for under $0.10

    31 parts599
  • 2 layers26.7 × 27.9 mmBreakout board, the printed circuit board in 3D

    Breakout board

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    31 parts546MIT
  • 2 layers100 × 50 mmPixelix, the printed circuit board in 3D

    Pixelix

    BlueAndi/Pixelix

    Full RGB LED matrix, based on an ESP32 and WS2812B LEDs or emulated LEDs on TFT.

    31 parts447MIT
  • 2 layers77.2 × 69.8 mmCubesatsim solar, the printed circuit board in 3D

    Cubesatsim solar

    alanbjohnston/CubeSatSim

    CubeSatSim, the AMSAT CubeSat Simulator

    31 parts419GPL-3.0
  • 2 layers103 × 55 mmTd neck-294, the printed circuit board in 3D

    Td neck-294

    tdaede/td-crt

    tubes

    31 parts373

Questions

How big is the Piezo preamp dual PCB?

It measures 26 × 16.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Piezo preamp dual use?

31 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Piezo preamp dual KiCad files?

From the compuphase/piezo-preamplifier repository on GitHub, at the commit this page was made from: the board is piezo-preamp-dual.kicad_pcb and its schematic piezo-preamp-dual.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Piezo preamp dual design in my own project?

Its repository states no licence, so its author keeps all rights: ask compuphase before reusing the design.