Skip to the content
2 layers61 × 35.6 mmTft dashboard pcb, the printed circuit board in 3D

Two-layer ESP32 carrier PCB for an SPI TFT display and rotary encoder, designed in KiCad.

Size
61 × 35.6 mm
Copper layers
2
Thickness
1.6 mm
Parts
4
Nets
33
Pads
46
Tracks, vias
0, 0
Routed
Not yet
KiCad
KiCad 10.0 (file 20260206)
Created
26 Oct 2026
Updated
26 Oct 2026

Overview

Tft dashboard pcb is an open-source printed circuit board by cmdsreedev, from the cmdsreedev/tft-dashboard-pcb repository on GitHub. It is a 2-layer board of 61 × 35.6 mm with 4 parts on 33 nets.

It belongs with the lEDs and displays boards and the ESP32 boards of this library.

README

README.md

ESP32 TFT Dashboard PCB

A compact two-layer carrier board for building a small ESP32-based dashboard. It connects a 30-pin ESP32 development board to an SPI TFT display and a five-pin rotary encoder, with four M2 mounting holes for mechanical assembly.

Project status: Hardware design / first-revision prototype. Review the connector orientation and module pinouts against your exact ESP32 and TFT modules before fabrication or assembly.

Features

  • Socketed 30-pin ESP32 development board
  • 11-pin SPI TFT display connection
  • Five-pin JST-XH rotary encoder connection
  • Bottom-layer ground plane
  • Four non-plated 2.2 mm mounting holes for M2 hardware
  • Through-hole construction for straightforward hand assembly
  • KiCad source files and FreeCAD mechanical models

Board specification

PropertyValue
Board size79.2 × 54.46 mm
Layers2
SubstrateFR-4
Thickness1.6 mm
Copper weight1 oz / 35 µm
Signal trace width0.25 mm
Power trace width0.56 mm
Mounting holes4 × 2.2 mm NPTH

Interfaces

TFT display

The display header carries 3V3, GND, backlight, clock, serial data, data/command, reset, and chip-select signals. The PCB silkscreen identifies pin 1 and the power connections.

Rotary encoder

The JST-XH connector carries ENC_CLK, ENC_DT, ENC_SW, 3V3, and GND.

Repository contents

  • tft-design.kicad_pro — main KiCad project
  • tft-design.kicad_sch — schematic
  • tft-design.kicad_pcb — PCB layout
  • tft-design.FCStd — FreeCAD mechanical model
  • tft-design_resized.FCStd — alternate/resized mechanical model
  • 1.kicad_pro and 1.kicad_pcb — additional KiCad design files retained with the project

Fabrication outputs are intentionally not tracked. Generate fresh Gerber and drill files from the current PCB revision before ordering.

Fabrication export

  1. Open tft-design.kicad_pro in KiCad 10 or a compatible newer release.
  2. Open PCB Editor, refill copper zones, and run the Design Rules Checker.
  3. Plot F.Cu, B.Cu, F.Mask, B.Mask, F.SilkS, B.SilkS, and Edge.Cuts as Gerbers.
  4. Generate both PTH and NPTH Excellon drill files.
  5. Load every Gerber and both drill files in Gerber Viewer.
  6. Confirm the outline, plated connector holes, non-plated mounting holes, copper, and silkscreen before creating the fabrication ZIP.

Assembly checks

Before powering the board:

  • Confirm the ESP32 header orientation and pin-1 positions.
  • Confirm the TFT module uses the expected 11-pin ordering.
  • Verify that the TFT module includes suitable backlight current limiting, or add an appropriate external driver/current-limiting solution.
  • Check for shorts between 3V3 and GND.
  • Power the board with a current-limited supply for initial bring-up.

Software

Firmware is not included in this repository. The chosen display driver and GPIO definitions must match the fitted TFT module and the PCB net assignments.

Parts

4
QtyValueFootprintReferences
2Conn_01x15Connector_PinSocket_2.54mm:PinSocket_1x15_P2.54mm_VerticalESP32_Left1, ESP32_Right1
1Conn_01x05Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_VerticalROTARY_ENCODER1
1Conn_01x11Connector_PinSocket_2.54mm:PinSocket_1x11_P2.54mm_VerticalTFT_DISPLAY1

More from cmdsreedev/tft-dashboard-pcb

1
  • 2 layers79.2 × 54.5 mmTft design, the printed circuit board in 3D

    Tft design

    cmdsreedev/tft-dashboard-pcb

    Two-layer ESP32 carrier PCB for an SPI TFT display and rotary encoder, designed in KiCad.

    8 parts

Similar boards

  • 2 layers18.5 × 26 mm24g2usb rp2350zero, the printed circuit board in 3D

    24g2usb rp2350zero

    joypad-ai/joypad-os

    Universal controller firmware for building adapters, dongles, and custom controllers.

    4 parts1.7kApache-2.0
  • 2 layers116 × 33 mm966595-1 and 963356-1, the printed circuit board in 3D

    966595-1 and 963356-1

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    4 parts1.2k
  • 2 layers19 × 18 mmDaughter board, the printed circuit board in 3D

    Daughter board

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    4 parts915
  • 2 layers24.8 × 24.8 mmNrf24 breakout, the printed circuit board in 3D

    Nrf24 breakout

    tardate/LittleArduinoProjects

    a collection of "Little Electronic & Arduino Projects", most involving electronics or an Arduino in one way or another!

    4 parts803MIT
  • 2 layers26 × 20 mmCap chain, the printed circuit board in 3D

    Cap chain

    drandyhaas/KiCadRoutingTools

    A set of Python/Rust tools to aid routing in KiCad

    4 parts744MIT
  • 2 layers34.7 × 20 mmXG Station Power MSI, the printed circuit board in 3D

    XG Station Power MSI

    osy/XG_Mobile_Station

    Open source eGPU dock for ROG Ally and ROG Flow

    4 parts712CC-BY-4.0
  • 2 layers20.3 × 24.5 mmJack power input, the printed circuit board in 3D

    Jack power input

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    4 parts546MIT

Questions

How big is the Tft dashboard pcb PCB?

It measures 61 × 35.6 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Tft dashboard pcb use?

4 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Tft dashboard pcb KiCad files?

From the cmdsreedev/tft-dashboard-pcb repository on GitHub, at the commit this page was made from: the board is 1.kicad_pcb and its schematic tft-design.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Tft dashboard pcb design in my own project?

Its repository states no licence, so its author keeps all rights: ask cmdsreedev before reusing the design.