
Pan Mix B
clarionut/YuSynth-Panning-Mixer-Output
An extensible version of the YuSynth Output mixer & VC-panner, minus the tone control circuitry

An extensible version of the YuSynth Output mixer & VC-panner, minus the tone control circuitry
Pan Mix A is an open-source printed circuit board by clarionut, from the clarionut/YuSynth-Panning-Mixer-Output repository on GitHub. It is a 2-layer board of 73 × 78.1 mm with 98 parts on 73 nets, routed with 398 tracks and 0 vias.
It is built around the LM13700M, TL072 and BC557, with the BC557B among its other parts. Its parts include 58 resistors, 20 capacitors, 6 ICs, 6 connectors and 4 transistors. It belongs with the audio and music boards of this library.
An extensible version of the YuSynth Output mixer & VC-panner, minus the tone control circuitry.
Very early in the construction of my modular synth it became obvious that I was going to need a multi-channel mixer as an output stage. I'd already built a few YuSynth modules, so his Mixout-VC Panner seemed like a promising choice especially as I had an old dual VU meter which could be pressed into service.
The original design includes a passive tone control circuit (which I chose to omit) and uses a two-board architecture with the four VC panner circuits on one board and the mixer and output circuitry on another. My synth is in Eurorack format, so I wanted to keep the board sizes as small as possible (which also makes them cheaper!). I decided to use an alternative physical architecture with the mixer output board (board B in my design) as a motherboard, with two 2-channel VC-panner boards (board A) plugged into it using pin headers.
This allows easy extensibility by adding further 2-channel VC-panner boards mounted on their own panels, daisy-chained from a header on the motherboard. I have indeed added an additional pair of inputs since originally building the module. Details of the construction are shown in the pictures folder. Note that the two VC-panner boards mounted on the motherboard have the header pins on the front side on one board and the back side on the other to keep the wiring as clean as possible. Most of the pin headers on the motherboard are on the back side of the board. The pictures also show the additional input board and panel.
I replaced the original non-backlit VU meter with one which can be illuminated, and soldered a 2 pin header to the back of the main power input connection with flying leads to the resistor/LED positioned behind the meter.
The schematic folder contains PDFs of the schematic and layout for the VC-panner boards (A) and the motherboard (B). The Kicad projects for these are in their own individual subfolders.
I've also include the gerbers in case these are of direct use to anyone.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 100n | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C104, C105, C106, C107, C108, C109, C204, C205, C206, C207, C208, C209 |
| 12 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R108, R120, R124, R129, R132, R137, R208, R220, R224, R229, R232, R237 |
| 8 | 100R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R125, R126, R133, R134, R225, R226, R233, R234 |
| 6 | 100k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R104, R130, R138, R204, R230, R238 |
| 6 | 150k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R105, R106, R107, R205, R206, R207 |
| 4 | 15k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R127, R135, R227, R235 |
| 4 | 200k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R102, R103, R202, R203 |
| 4 | 27k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R122, R123, R222, R223 |
| 4 | 2k2 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R109, R121, R209, R221 |
| 4 | 33k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R128, R136, R228, R236 |
| 4 | 47u | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C102, C103, C202, C203 |
| 3 | BC557 | Package_TO_SOT_THT:TO-92_HandSolder | Q101, Q201, Q202 |
| 2 | 10u | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C1, C2 |
| 2 | 1M | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R131, R231 |
| 2 | 24k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3, R4 |
| 2 | 330k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R101, R201 |
| 2 | 47u NP | Capacitor_THT:C_Radial_D6.3mm_H5.0mm_P2.50mm | C101, C201 |
| 2 | 50k | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | RV101, RV201 |
| 2 | LM13700 | Package_DIP:DIP-16_W7.62mm_Socket | U103, U203 |
| 2 | TL072 | Package_DIP:DIP-8_W7.62mm_Socket | U102, U202 |
| 2 | TL074 | Package_DIP:DIP-14_W7.62mm_Socket | U101, U201 |
| 1 | BC557B | Package_TO_SOT_THT:TO-92_HandSolder | Q102 |
| 1 | IN1 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | IN2 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | MAIN | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J6 |
| 1 | PAN1 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | PAN2 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | PAN_V | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
The 96 most common of 98 parts.

clarionut/YuSynth-Panning-Mixer-Output
An extensible version of the YuSynth Output mixer & VC-panner, minus the tone control circuitry



FabianGmeiner/BMW_E30_SI_Board
Reverse engineering and improving the BMW E30 service indicator board

sporniket/kicad-conversions--thomson-mo5--v1
A conversion to Kicad EDA of the schematics of a computer released around 1984 known as the "Thomson MO5".


Ansel84/BMW-E30-Gauge-Cluster-Late-Model
This project is the documentation of reverse engineering the BMW E30 gauge cluster for post 1988 model years.


DeniseViltes/dce-g5-proyecto_integrador
FIUBA - Electrónica - Taller de Diseño de Circuitos Electrónicos -Proyecto de diseño: Sistema de alimentación para aplicaciones industriales y automotrices
It measures 73 × 78.1 mm and has 2 copper layers, 1.6 mm thick.
98 parts, built around the LM13700M, TL072, BC557 and BC557B. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the clarionut/YuSynth-Panning-Mixer-Output repository on GitHub, at the commit this page was made from: the board is Schematic/Pan_Mix_A/Pan_Mix_A.kicad_pcb and its schematic Schematic/Pan_Mix_A/Pan_Mix_A.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask clarionut before reusing the design.