

Chademo charge controller
This repo contains a car-side implementation of the CHAdeMO EV charging standard including both the hardware and firmware.
- Size
- 134 × 120 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 64
- Nets
- 131
- Pads
- 333
- Tracks, vias
- 436, 41
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 14 Jul 2023
- Updated
- 4 Aug 2024
Overview
Chademo charge controller is an open-source printed circuit board by chrskly, from the chrskly/chademo-charge-controller repository on GitHub. It is a 2-layer board of 134 × 120 mm with 64 parts on 131 nets, routed with 436 tracks and 41 vias.
It is built around the SN65HVD230D, NCV8402ASTT1G and TPS62160DGKR, with the M22-2510346 and SS54B among its other parts. Its parts include 23 resistors, 13 ICs, 8 diodes, 7 capacitors and 5 connectors. It belongs with the RP2040 boards of this library.
Main components
5SN65HVD230D
SOIC-8-40℃~+85℃ 1 17mA 1Mbps 370uA 3V~3.6V CAN Transceiver Low-power mode、Wake-up function、ESD protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversNCV8402ASTT1G
SOT-223-3-40℃~+150℃ 165mΩ 2A Low Side Switch Over Voltage Protection、Overcurrent Protection(OCP)、Overtemperature protection (OTP) SOT-223-3 Power Distribution Switches ROHSonsemiGate DriversTPS62160DGKR
MSOP-8-40℃~+85℃@(TA) 1 17uA 1A 2.25MHz 3V~17V 900mV~6V Adjustable Buck Buck Built-in Yes MSOP-8 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersM22-2510346
插件,P=2mmPin HeadersHarwinSS54B
SMBSchottky Diodeshongjiacheng
README
README.mdCHAdeMO Implementation
This repo contains a car-side implementation of the CHAdeMO EV charging standard including both the hardware and firmware.
Features
- Supports CHAdeMO protocols v0.9, v1.0, and v2.0.
- Automatic sleep, wake on plug insertion.
- Separate manual wake button option.
Chademo Plug Pinout
- Ground
- CP : evse => car, IN1, contactor +ve signal, goes high when active, sensed by 'f'
- nc
- CP3 : car => evse, OUT1, charge enable, sensed by 'k'
- HV-
- HV+
- CS : connection check, goes low when plug inserted, sensed by 'h'
- CAN H
- CAN L
- CP2 : evse => car, IN2, contactor -ve signal, goes low when active, sensed by 'g'
OUT2, contactor override, pull low to allow CP2 signal through
Charging start sequence
- Car pulls CP high (12V) through R3 (1kΩ) when plug is inserted
- User presses start button on station
- Station pulls CP high (IN1), d1 closes, +ve contactor closes
- Car and station start sending CAN messages
- Car and station check each others params for compatability
- Car pulls CP3 low and sets CAN vehicleChargingEnabled flag to true to indicate it is ready to go ahead with charging
- Station locks plug to vehicle
- Station performs insulation test
- Station pulls CP2 low (IN2), d2 closes, -v3 contactor closes
- Car ramps up current request. Energy transfer begins.
Charging stop sequence
- Car stops pulling CP3 low and sets CAN vehicleChargingEnabled to false.
- Station deactivates CP and CP2
- Station unlocks plug
Questions
- When to use vehicleChargingEnabled and when to use vehicleRequestingStop?
Parts
64| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 10 | Resistor_SMD:R_0805_2012Metric | R5, R8, R9, R11, R15, R20, R23 |
| 7 | LED | LED_SMD:LED_0805_2012Metric | D2, D3, D4, D5, D6, D7, D8 |
| 6 | PC817 | Package_DIP:DIP-4_W7.62mm | U2, U3, U4, U5, U6, U7 |
| 4 | 10uF | Capacitor_SMD:C_0603_1608Metric | C1, C5, C6, C7 |
| 4 | 1k6 | Resistor_SMD:R_0805_2012Metric | R4, R10, R16, R21 |
| 3 | 560 | Resistor_SMD:R_0805_2012Metric | R17, R18, R19 |
| 3 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3, J7, J8 |
| 2 | 100 | Resistor_SMD:R_0805_2012Metric | R7, R22 |
| 2 | 100nF | Capacitor_SMD:C_0603_1608Metric | C2, C3 |
| 2 | 120 | Resistor_SMD:R_0805_2012Metric | R12, R13 |
| 2 | MCP2515-I_ST | Library:SOP65P640X120-20N | IC2, IC4 |
| 2 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_DIN965_Pad | H1, H2 |
| 2 | SN65HVD230 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | IC3, IC5 |
| 2 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP1, JP2 |
| 1 | 100k | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 1k | Resistor_SMD:R_0805_2012Metric | R14 |
| 1 | 2.2uH | Inductor_SMD:NR6028T220M | L1 |
| 1 | 200 | Resistor_SMD:R_0805_2012Metric | R6 |
| 1 | 220k | Resistor_SMD:R_0805_2012Metric | R2 |
| 1 | 22uF | Capacitor_SMD:C_0805_2012Metric | C4 |
| 1 | 47k | Resistor_SMD:R_0805_2012Metric | R3 |
| 1 | Conn_2Rows-57Pins | Connector:delphi56 | J2 |
| 1 | LOGO | LOGO | G*** |
| 1 | LOGO | Connector:chademo-logo-10x10 | G*** |
| 1 | M22-2510346 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Horizontal | J1 |
| 1 | NCV8402ASTT1G | Library:SOT230P700X175-4N | IC6 |
| 1 | Pico | Module:RPi_Pico_SMD_TH | U1 |
| 1 | SS54B | Diode_SMD:DIOM5336X244N | D1 |
| 1 | TPS62160DGKR | Library:SOP65P490X110-8N | IC1 |
The 63 most common of 64 parts.
Similar boards
- 2 layers82.6 × 100.6 mm

- 2 layers145 × 115 mm

Tail lights
chrskly/electric-mustang-wiring
Wiring diagrams and PCBs for my Mustang EV conversion project
123 parts2 - 2 layers145 × 115.1 mm

Tail lights
chrskly/electric-mustang-taillights
This is a project to create a PCB to replace the original tail light lamps in a 1965 Ford Mustang.
127 parts - 4 layers180 × 120 mm

MG ZS V2
damienmaguire/MG-EV-Inverter
Reverse engineering of the drive motor and inverter used in MG Electric Vehicles
177 parts17GPL-3.0 - 4 layers38 × 39 mm

CLN17-V1.5
creapunk/CLN-ClosedLoopNemaDriver
Compact closed-loop stepper motor driver designed for NEMA motors
103 parts1.1k - 4 layers209 × 100 mm

- 4 layers154 × 154 mm

DC Controller STM32
andymartell/Prius-STM32-DC-Motor-Contoller
STM32 based DC Motor Controller using Prius Gen 3 hardware
293 parts - 2 layers100 × 50 mm

PicoRF Blk2B MTCS Mk2
madkoding/slimestuff
SlimeVR resources hub. Scripts, utilities, and complement documentation for the SlimeVR ecosystem.
90 parts
Questions
How big is the Chademo charge controller PCB?
It measures 134 × 120 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Chademo charge controller use?
64 parts, built around the SN65HVD230D, NCV8402ASTT1G, TPS62160DGKR and M22-2510346. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Chademo charge controller KiCad files?
From the chrskly/chademo-charge-controller repository on GitHub, at the commit this page was made from: the board is hardware/chademo-charge-controller/chademo-charge-controller.kicad_pcb and its schematic hardware/chademo-charge-controller/chademo-charge-controller.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Chademo charge controller design in my own project?
Its repository states no licence, so its author keeps all rights: ask chrskly before reusing the design.