Skip to the content
2 layers42.5 × 10.3 mmSata Adapter, the printed circuit board in 3D

A all in one controller for ws2812b led strips made for WLED

Size
42.5 × 10.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
2
Nets
22
Pads
40
Tracks, vias
24, 6
Pours
2
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
5 Jan 2026
Updated
23 Jan 2026

Overview

Sata Adapter is an open-source printed circuit board by Choccy-vr, from the Choccy-vr/WLED-Controller repository on GitHub. It is a 2-layer board of 42.5 × 10.3 mm with 2 parts on 22 nets, routed with 24 tracks and 6 vias.

It is built around the 10034814-001LF and UP20-C-F-G-FL-P12-TR. It belongs with the interfaces and adapters boards of this library.

Main components

2

README

README.md

WLED-Controller

An all-in-one controller for WS2812B LED strips, made for WLED. With Adapters for LEDs everywhere.

I made this because these WS2812B strips and WLED look so good, but all the other WLED controllers are quite expensive, and I would rather make it by myself. I set out to make it as small as possible, even if that means making it harder for me.

On the controller PCB, I integrated basically a esp32 c3 supermini. That is the bulk of it, but I also put some capacitors on the LED PWR line for smoothing the power out. I also added a P-channel MOSFET to allow for a soft start.

The various adapter PCBs adapt the specified port into 5v and GND and output it to a USB-C, inspired by Framework's modules

Images:

Schematic

Adapters
SATA Adapter

Barrel Jack Adapter

BOM

Product NameProduct DescriptionProduct LinkProduct unit priceProduct amountProduct CostTotal (Before Tax + Shipping)Total
Main PCB(A)The main control PCBhttps://jlcpcb.com/$8.715$35.45$59.27$67.38
Sata Adapter PCBSata adapterhttps://jlcpcb.com/$1.025$5.10
Barrel Adapter PCBBarrel adapterhttps://jlcpcb.com/$1.025$5.10
AntennaAntennahttps://www.digikey.com/en/products/detail/pulse-electronics/ANT3216A063R2400A/3927186$0.221$0.22
Bulk CapCap for LEDshttps://www.digikey.com/en/products/detail/rubycon/35PX470MEFC10X12-5/3134236$0.3410$3.44
Sata ConnectorConnector for SATA PCBhttps://www.digikey.com/en/products/detail/amphenol-cs-fci/10034814-001LF/1001349$6.841$6.84
USB-CMale USB Chttps://www.digikey.com/en/products/detail/same-sky-formerly-cui-devices/UP20-C-F-G-FL-P12-TR/24818610$1.302$2.60
Barrel JackConnector for Barrel PCBhttps://www.digikey.com/en/products/detail/same-sky-formerly-cui-devices/PJ-002A/96962$0.521$0.52

Parts

2
QtyValueFootprintReferences
110034814-001LF10034814_001LF:AMPHENOL_10034814-001LFJ2
1UP20-C-F-G-FL-P12-TRUP20_C_F_G_FL_P12_TR:SAMESKY_UP20-C-F-G-FL-P12-TRJ3

More from Choccy-vr/WLED-Controller

2
  • 4 layers18.3 × 42.3 mmUSB WLED Controller, the printed circuit board in 3D

    USB WLED Controller

    Choccy-vr/WLED-Controller

    A all in one controller for ws2812b led strips made for WLED

    39 parts
  • 2 layers13 × 14.8 mmBarrel Adapter, the printed circuit board in 3D

    Barrel Adapter

    Choccy-vr/WLED-Controller

    A all in one controller for ws2812b led strips made for WLED

    2 parts

Similar boards

  • 2 layers21 × 60.4 mmLeaf dongle, the printed circuit board in 3D

    Leaf dongle

    marcuswu/leaf-fall

    During the planning phase for my ULP switches, u/dynam1keNL posted about his mikefives, a radical new build that was diodeless, wireless, portless, and ultra-low power due to use of the Nordic Gazell wireless protocol…

    8 partsMIT
  • 2 layers37 × 19 mmPassive rpi hub75-adapter, the printed circuit board in 3D

    Passive rpi hub75-adapter

    hzeller/rpi-rgb-led-matrix

    Controlling up to three chains of 64x64, 32x32, 16x32 or similar RGB LED displays using Raspberry Pi GPIO

    2 parts4.4kGPL-2.0
  • 2 layersDiode template, the printed circuit board in 3D

    Diode template

    adamws/kicad-kbplacer

    KiCad plugin for automatic keyboard's key placement and routing

    2 parts547GPL-3.0
  • 2 layers20.3 × 15.2 mmL0 button, the printed circuit board in 3D

    L0 button

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    2 parts546MIT
  • 2 layers35.1 × 46.8 mmSDEX2M2 Breakout Board, the printed circuit board in 3D

    SDEX2M2 Breakout Board

    NVNTLabs/switch2-SDEX2M2

    Micro SD Express to M.2 NVME Adapter for Nintendo Switch 2

    2 parts542GPL-3.0
  • 2 layers59.3 × 36.6 mmExpansionBoardTemplate, the printed circuit board in 3D

    ExpansionBoardTemplate

    BlueSCSI/BlueSCSI-v2

    BlueSCSI v2/Ultra - an open source, open hardware, SCSI emulator using the Pi Pico PR2040 and Pico 2 RP2350

    2 parts459GPL-3.0
  • 2 layersAlpha.9mm.wire, the printed circuit board in 3D

    Alpha.9mm.wire

    ohmtech-rdi/eurorack-blocks

    Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

    2 parts410

Questions

How big is the Sata Adapter PCB?

It measures 42.5 × 10.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Sata Adapter use?

2 parts, built around the 10034814-001LF and UP20-C-F-G-FL-P12-TR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Sata Adapter KiCad files?

From the Choccy-vr/WLED-Controller repository on GitHub, at the commit this page was made from: the board is PCB/Sata/Sata_Adapter.kicad_pcb and its schematic PCB/Barrel/Barrel_Adapter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Sata Adapter design in my own project?

Its repository states no licence, so its author keeps all rights: ask Choccy-vr before reusing the design.