Skip to the content
2 layers51.3 × 20.3 mmRpi 8x2 v1, the printed circuit board in 3D

rpi_level_shifter_v1

Size
51.3 × 20.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
18
Nets
38
Pads
136
Tracks, vias
687, 84
Pours
3
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
7 Apr 2023
Updated
7 Jul 2023

Overview

Rpi 8x2 v1 is an open-source printed circuit board by charkster, from the charkster/rpi_level_shifter_v1 repository on GitHub, published under the MIT licence. It is a 2-layer board of 51.3 × 20.3 mm with 18 parts on 38 nets, routed with 687 tracks and 84 vias.

It is built around the NVT2010PW and AP2112K-1.8. Its parts include 4 capacitors, 4 ICs, 4 connectors and 2 resistors. It belongs with the interfaces and adapters boards of this library.

Main components

2

README

README.md

rpi_level_shifter_v1

Raspberry Pi level shifter for 10 signals (two boards can fit on the same 40 pin header). Two NVT2010PW ICs are available on a single board, to either level shift from 3.3V to 5V or from 3.3V to 1.8V and 1.2V (jumper selectable). The RPi's 5V is used for the 5V level shift and two on-board LDO regulators are available for shifting levels down to 1.8V or 1.2V. Other voltages can be used, but it is recommended that they not be between 2.6V and 4.3V.

This board is designed to not fit over-top the RPi board, but rather over the side.

picture

Each board needs to have the top-left pin of J1 connected to the 3.3V RPi header pin. One board can service the I2C and UART pins (along with a couple of GPIO) and another board can service SPI pins. BCM GPIO's 13, 16, 19, 20, 21 and 26 are not accessable with this board.

picture

Check-out my PDF schematic !!

Check-out the CSV Bill of Materials !!

The J3 connector must only have one horizontal jumper!! Either HV_EN or LV_EN, or damage to the RPi pins may occur (you have been warned). Additionally, the J4 connector must only have one horizontal jumper!! The RPI_5V is only available if the level shifter board is at the top of the header, otherwise you will need to jumper wire the 5V to the VEXT pin.

UPDATES: SPI at 5V is working well to 10MHz with the 1k Ohm pull-up resistors. This matches nicely with the NVT2010PW datasheet. I lowered the pull-up resistors to 500 Ohm and was able to get SPI working at 12MHz. I was not able to run faster than 12MHz at 5V. Power consumption was about 0.5W for both the 0.5k and 1k pull-up resistors.

picture

Parts

18
QtyValueFootprintReferences
4R_Network05Resistor_THT:R_Array_SIP6RN1, RN2, RN3, RN4
2100pFResistor_SMD:R_0603_1608MetricC1, C2
210uFResistor_SMD:R_0603_1608MetricC3, C4
2200kCapacitor_SMD:C_0603_1608MetricR1, R2
2Conn_02x08_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x08_P2.54mm_VerticalJ1, J2
2NVT2010PWPackage_SO:TSSOP-24_4.4x7.8mm_P0.65mmU1, U4
1AP2112K-1.2Package_TO_SOT_SMD:SOT-23-5U3
1AP2112K-1.8Package_TO_SOT_SMD:SOT-23-5U2
1Conn_02x02_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_VerticalJ3
1Conn_02x03_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_VerticalJ4

Similar boards

  • 2 layers26.9 × 38.3 mmXiao level shifter v1, the printed circuit board in 3D

    Xiao level shifter v1

    charkster/xiao_rp2040_level_shifter_v1

    Add-on PCB board for Seeed Studio Xiao RP2040, which provides 1.2V and 1.8V selectable level-shifting.

    14 parts1MIT
  • 4 layers27 × 80 mmLedmatrix, the printed circuit board in 3D

    Ledmatrix

    bitluni/Mdot2Matrix

    276 parts104MIT
  • 2 layers91.3 × 53.3 mmTimep, the printed circuit board in 3D

    Timep

    Matir/timep

    Test Interface for Multiple Embedded Protocols

    89 parts25Apache-2.0
  • 4 layers39 × 54 mmCaravel mvp, the printed circuit board in 3D

    Caravel mvp

    TinyTapeout/caravel-mvp-pcb

    the minimum necessary to use a Caravel chip (Google MPW or chipIgnite)

    58 parts8Apache-2.0
  • 4 layers61.8 × 27.5 mmAudio Processing HW V1.0, the printed circuit board in 3D

    Audio Processing HW V1.0

    aitesam961/OpenADSP

    An Embedded Digital Signal Processing Device for Audio signals.

    83 parts4GPL-3.0
  • 2 layers45 × 35.5 mmWearable revB, the printed circuit board in 3D

    Wearable revB

    AhmedDoesECE/wearable-health-monitor

    45 parts1MIT
  • 2 layers38 × 42 mmSpectrometer, the printed circuit board in 3D

    Spectrometer

    dpohanlon/isaac

    Reconstructing low-resolution spectra from Osram sensors

    20 parts1MIT
  • 2 layers29 × 23 mmMCU, the printed circuit board in 3D

    MCU

    Ironman-007/Digital_Artifact

    Input devices: - mouse encoder: https://www.amazon.com/gp/product/B0CF9FS3QS/ref=ppxyodtbasintitleo00s00?ie=UTF8&psc=1 - thumb joystick: https://www.adafruit.com/product/5628 - thumbwheel: -…

    36 parts1

Questions

How big is the Rpi 8x2 v1 PCB?

It measures 51.3 × 20.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Rpi 8x2 v1 use?

18 parts, built around the NVT2010PW and AP2112K-1.8. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Rpi 8x2 v1 KiCad files?

From the charkster/rpi_level_shifter_v1 repository on GitHub, at the commit this page was made from: the board is rpi_8x2_v1.kicad_pcb and its schematic rpi_8x2_v1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Rpi 8x2 v1 design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).