

ESP32-DevKit Custom
4-layer ESP32 development board PCB clone based on Espressif ESP32-DevKitC-v4 reference design, made in KiCad
- Size
- 30.4 × 56.5 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 36
- Nets
- 68
- Pads
- 244
- Tracks, vias
- 867, 40
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 26 Jun 2026
- Updated
- 28 Jun 2026
Overview
ESP32-DevKit Custom is an open-source printed circuit board by chackojose2005-zodiac, from the chackojose2005-zodiac/ESP32-DevKit-Custom repository on GitHub, published under the MIT licence. It is a 4-layer board of 30.4 × 56.5 mm with 36 parts on 68 nets, routed with 867 tracks and 40 vias.
It is built around the CP2102N-A01-GQFN28R, ESP32-WROOM-32D and AMS1117-3.3, with the MMSS8050-H-TP among its other parts. Its parts include 10 resistors, 9 capacitors, 5 diodes, 3 connectors and 2 ICs. It belongs with the microcontroller boards boards and the ESP32 boards of this library.
Main components
4CP2102N-A01-GQFN28R
QFN-28-EP(5x5)-40℃~+85℃ 13.7mA 195uA 3Mbps 3V~3.6V Transceiver USB 2.0 QFN-28-EP(5x5) USB Converters ROHSSilicon LabsUSB ConvertersESP32-WROOM-32D
-- WiFi Modules ROHSEspressif SystemsWiFi ModulesAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMMSS8050-H-TP
SOT-23-55℃~+150℃ 1 NPN 1.5A 100MHz 100nA 120 25V 300mW 500mV 5V NPN SOT-23 Bipolar (BJT) ROHSMicro Commercial ComponentsBipolar (BJT)
README
README.mdESP32 Development Kit — Custom PCB Design
A 4-layer KiCad PCB clone of the Espressif ESP32-DevKitC-v4, designed from the official reference schematic.
Table of Contents
- Overview
- Board Specifications
- Schematic & Design Details
- Bill of Materials (BOM)
- Layer Stack-Up
- Repository Structure
- How to Open in KiCad
- How to Order the PCB
- Design Notes & Customizations
- References
- Author
Overview
This project is a custom clone of the Espressif ESP32-DevKitC-v4 development board, designed entirely in KiCad. The design is based on the official Espressif reference schematic and layout, with minor modifications for ease of hand assembly.
The board features:
- ESP32-WROOM-32D module with integrated PCB antenna
- CP2102N USB-to-UART bridge for serial programming
- AMS1117-3.3 LDO voltage regulator (3.3 V output)
- BOOT and EN push buttons
- 2 × 19-pin header connectors exposing all GPIO pins
- SMD components on both front and back copper layers
Board Dimensions: 30.73 mm × 56.90 mm
Layer Count: 4 layers
Form Factor: Matches the original ESP32-DevKitC-v4
Board Specifications
| Parameter | Value |
|---|---|
| Microcontroller | ESP32-WROOM-32D |
| USB-UART Bridge | CP2102N-A01-GQFN28 |
| Voltage Regulator | AMS1117-3.3 (SOT-223) |
| Input Voltage | 5 V via Micro-USB |
| Output Voltage | 3.3 V regulated |
| GPIO Headers | 2 × 19-pin, 2.54 mm pitch |
| Board Layers | 4 (Signal / Signal / Signal / Signal) |
| Board Dimensions | 30.73 mm × 56.90 mm |
| Component Standard | SMD (0402 / 0603 packages) |
| KiCad Version | KiCad 7 / 8 |
Schematic & Design Details
The schematic is organized into five functional blocks, mirroring the Espressif reference design:
- Power Supply — Micro-USB input → AMS1117-3.3 LDO → 3.3 V rail with decoupling capacitors
- USB / USB-UART — CP2102N bridge with ESD protection diodes (D4, D5, D6) and auto-reset circuit
- ESP32 Module — ESP32-WROOM-32D with all GPIO broken out to headers
- Switch Buttons — BOOT (GPIO0) and EN (chip enable) with RC debounce networks
- Connectors — J2 and J3 (2 × 19-pin headers)
The auto-reset circuit uses two MMSS8050 NPN transistors (Q1, Q2) driven by the CP2102N's RTS and DTR lines. This allows the Arduino IDE and esptool.py to reset and flash the ESP32 without pressing buttons manually.
Bill of Materials (BOM)
| Reference | Value | Footprint |
|---|---|---|
| C1, C2, C21 | 22 µF / 10 V (20%) | Capacitor_SMD:C_0201_0603Metric |
| C9, C14, C19, C22 | 0.1 µF / 50 V (10%) | Capacitor_SMD:C_01005_0402Metric |
| C15 | 0.1 µF / 50 V (NC) | Capacitor_SMD:C_01005_0402Metric |
| C20 | 4.7 µF / 6.3 V | Capacitor_SMD:C_01005_0402Metric |
| D1 | LED | LED_SMD:LED_0603_1608Metric |
| D3 | Schottky Diode | Diode_SMD:D_SOD-323 |
| D4, D5, D6 | TVS Diode | Diode_SMD:D_SOD-523 |
| J1 | USB Micro-B | Connector_USB:USB_MicroAB_Molex_47590-0001 |
| J2, J3 | 19-pin Male Header | Connector_PinHeader_2.54mm:PinHeader_1x19_... |
| MOD1 | ESP32-WROOM-32D | ESP32-WROOM32D.pretty:ESP32-WROOM-32D |
| Q1, Q2 | MMSS8050-H-TP | digikey-footprints:SOT-23-3 |
| R2, R24 | 2 KΩ (5%) | Resistor_SMD:R_01005_0402Metric |
| R7, R18 | 0 Ω (5%) | Resistor_SMD:R_01005_0402Metric |
| R11, R21, R22 | 10 KΩ (5%) | Resistor_SMD:R_01005_0402Metric |
| R23 | 10 KΩ (NC) | Resistor_SMD:R_01005_0402Metric |
| R25 | 22.1 KΩ (5%) | Resistor_SMD:R_01005_0402Metric |
| R26 | 47.5 KΩ (5%) | Resistor_SMD:R_01005_0402Metric |
| SW1, SW2 | Push Button | Button_Switch_SMD:SW_SPST_B3S-1000 |
| U1 | CP2102N-A01-GQFN28 | Package_DFN_QFN:TQFN-28-1EP_5x5mm_P0.5mm |
| U2 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 |
(NC) = Not Connected / DNP (Do Not Populate)
Layer Stack-Up
| Layer | KiCad Name | Purpose |
|---|---|---|
| Layer 1 | F.Cu | Signal routing (top) |
| Layer 2 | In1.Cu | Signal routing (inner 1) |
| Layer 3 | In2.Cu | Signal routing (inner 2) |
| Layer 4 | B.Cu | Signal routing (bottom) |
All four copper layers are used for signal routing. Power (VCC/3.3 V) and ground (GND) connections are routed as copper tracks across all layers using KiCad's autorouter, rather than as dedicated power or ground planes. This approach was used to complete all 68 nets with 0 unrouted connections.
Note: In a production design, dedicated inner ground and power planes (In1.Cu = GND, In2.Cu = PWR) are recommended for better RF performance and signal integrity. For this educational clone, autorouted tracks on all four layers achieve full connectivity.
Repository Structure
ESP32-DevKit-Custom/
│
├── ESP32-DevKit-Custom.kicad_pro # KiCad project file
├── ESP32-DevKit-Custom.kicad_sch # Schematic
├── ESP32-DevKit-Custom.kicad_pcb # PCB layout
│
├── ESP32-WROOM32D.pretty/ # Custom ESP32-WROOM-32D footprint
├── CP2102N-A01-GQFN28footprint.pretty/ # Custom CP2102N footprint
├── MMSS8050-H-TPfootprint.pretty/ # Custom MMSS8050 footprint
│
├── Gerbers/ # Manufacturing files
│ ├── ESP32-DevKit-F_Cu.gtl
│ ├── ESP32-DevKit-In1_Cu.g2
│ ├── ESP32-DevKit-In2_Cu.g3
│ ├── ESP32-DevKit-B_Cu.gbl
│ ├── ESP32-DevKit-F_Mask.gts
│ ├── ESP32-DevKit-B_Mask.gbs
│ ├── ESP32-DevKit-F_Silkscreen.gto
│ ├── ESP32-DevKit-B_Silkscreen.gbo
│ ├── ESP32-DevKit-Edge_Cuts.gm1
│ └── ESP32-DevKit-drill.drl
│
├── BOM/
│ └── ESP32-DevKit-BOM.csv # Bill of materialsHow to Open in KiCad
Prerequisites
- KiCad 7 or later installed
- Internet connection (to download symbol/footprint libraries if missing)
Steps
-
Clone this repository:
bash git clone https://github.com/chackojose2005-zodiac/ESP32-DevKit-Custom.git cd ESP32-DevKit-Custom -
Open KiCad: Launch KiCad and click File → Open Project, then select
ESP32-DevKit-Custom.kicad_pro. -
Open the Schematic: In the KiCad project manager, double-click Schematic Editor (
.kicad_sch) to view the schematic. -
Open the PCB Layout: Double-click PCB Editor (
.kicad_pcb) to open the board layout. -
Verify the 3D View: In the PCB Editor, go to View → 3D Viewer to see the 3D render of the board.
-
Run DRC (Design Rule Check): In the PCB Editor, go to Inspect → Design Rules Checker and click Run DRC to verify the design.
How to Order the PCB
Generating Gerber Files (if not already included)
- Open the PCB in KiCad PCB Editor.
- Go to File → Fabrication Outputs → Gerbers (.gbr).
- Select all layers (F.Cu, In1.Cu, In2.Cu, B.Cu, F.Mask, B.Mask, F.Silkscreen, B.Silkscreen, Edge.Cuts).
- Click Plot.
- Also generate drill files: File → Fabrication Outputs → Drill Files (.drl).
- Zip the entire
Gerbers/folder.
Ordering from JLCPCB (Recommended)
- Go to jlcpcb.com and click Order Now.
- Upload the zipped Gerber files.
- Set the following options:
- Layers: 4
- Dimensions: Auto-detected (~30.73 × 56.90 mm)
- PCB Quantity: 5 (minimum)
- Surface Finish: HASL (lead-free) or ENIG
- Copper Weight: 1 oz
- Review the board preview, then proceed to checkout.
Note: 4-layer boards cost slightly more than 2-layer boards. JLCPCB's 4-layer pricing starts from around $2–5 per board for small quantities.
Design Notes & Customizations
This design is faithful to the Espressif ESP32-DevKitC-v4 reference, with the following intentional modifications:
-
ESP32-WROOM-32D module used — The design uses the ESP32-WROOM-32D variant with a custom footprint, featuring a single rectangular SMD thermal pad (pad 39) for GND instead of individual through-hole vias.
-
Autorouted PCB layout — All nets (GND, 3.3 V, signals) are connected using KiCad's autorouter across all four copper layers (F.Cu, In1.Cu, In2.Cu, B.Cu). The result is 0 unrouted connections across all 68 nets.
-
Voltage regulator (U2 / AMS1117-3.3) placed on the back copper layer (B.Cu) — In the original Espressif reference, the regulator is on the front. Moving it to the back frees up front-side real estate for small passives, making hand-soldering easier.
-
Custom footprints — The ESP32-WROOM-32D, CP2102N-A01-GQFN28, and MMSS8050-H-TP footprints were created from scratch and are included in the repository as local
.prettylibraries.
Other design considerations:
- The ESP32's RF antenna extends outside the board edge to avoid copper interference with the 2.4 GHz signal.
- TVS diodes (D4, D5, D6) protect the USB data lines against ESD events.
- RC networks on BOOT and EN pins prevent spurious resets due to contact bounce.
References
- Espressif ESP32-DevKitC-v4 Reference Design — Official schematics, PCB layout, BOM, and Gerber files
- ESP32-WROOM-32D Datasheet
- CP2102N Datasheet — Silicon Labs
- AMS1117-3.3 Datasheet
- KiCad Documentation
Author
Chacko Jose
B.Tech Electronics & Communication Engineering, Semester 2
School of Engineering, CUSAT, Kochi
GitHub: @chackojose2005-zodiac
This project was completed as part of Week 4 — Project 6 of the embedded systems PCB design curriculum.
Parts
36| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 0.1uF/50V(10%) | Capacitor_SMD:C_01005_0402Metric | C9, C14, C22 |
| 3 | 10K(5%) | Resistor_SMD:R_01005_0402Metric | R11, R21, R22 |
| 3 | 22uF/10V(20%) | Capacitor_SMD:C_01005_0402Metric | C1, C2, C21 |
| 3 | D_TVS | Diode_SMD:D_SOD-523 | D4, D5, D6 |
| 2 | 0.1uF/50V(10%)(NC) | Capacitor_SMD:C_01005_0402Metric | C15, C19 |
| 2 | 0R(5%) | Resistor_SMD:R_01005_0402Metric | R17, R18 |
| 2 | 2K(5%) | Resistor_SMD:R_01005_0402Metric | R2, R24 |
| 2 | Conn_01x19_Pin | Connector_PinHeader_2.54mm:PinHeader_1x19_P2.54mm_Vertical | J2, J3 |
| 2 | MMSS8050-H-TP | MMSS8050-H-TPfootprint:TRANS_MMSS8050-H-TP | Q1, Q2 |
| 2 | SW_Push | Button_Switch_SMD:SW_SPST_B3S-1000 | SW1, SW2 |
| 1 | 10K(5%)(NC) | Resistor_SMD:R_01005_0402Metric | R23 |
| 1 | 22.1K(5%) | Resistor_SMD:R_01005_0402Metric | R25 |
| 1 | 4.7uF/6.3V(10%) | Capacitor_SMD:C_01005_0402Metric | C20 |
| 1 | 47.5K(5%) | Resistor_SMD:R_01005_0402Metric | R26 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | CP2102N-A01-GQFN28 | CP2102N-A01-GQFN28footprint:QFN50P500X500X80-29N | U1 |
| 1 | D_Schottky | Diode_SMD:D_SOD-323 | D3 |
| 1 | ESP32-WROOM-32D | ESP32-WROOM32D:MODULE_ESP32-WROOM-32D | MOD1 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | LOGO | logo:LOGO | G*** |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-AB_Molex_47590-0001 | J1 |
The 35 most common of 36 parts.
Similar boards
- 4 layers30.3 × 56.7 mm

- 4 layers30.9 × 56.7 mm

ESP32-Dev Kit
Jazildebug/ESP32-Dev-Kit
KiCad project files for an ESP32 development board — schematic, PCB layout, and footprints for a custom dev kit design.
34 parts - 4 layers30.7 × 56.9 mm

ESP32 Clone devkit
futureshocked/KLP3e_ESP32_development_kit
This is the repository for the "ESP32 Devkit clone" project.
36 parts5 - 4 layers31.4 × 57.3 mm

ESP32 Clone Devkit
futureshocked/KLP4e_ESP32-Clone-Devkit
This is the repository for the "ESP32 devikit clone" project.
34 parts5MIT - 4 layers35.7 × 55.4 mm

- 4 layers30.5 × 56.8 mm

ESP 32 DEV KIT PCB Layout
RTX17LEO/ESP-32-DEV-MODULE
The ESP32 Dev Module is a powerful microcontroller with built-in Wi-Fi and Bluetooth, widely used for IoT and embedded applications.
34 parts - 2 layers67.1 × 88.4 mm

DE429 001 INSTALL
Purdue-Northwest-Vibration-Anaylsis/Purdue-Northwest-Vibration-Analysis
Vibration analysis senior design project for purdue northwest.
48 parts2 - 2 layers65 × 30 mm

Epaper
TDA-2030/E-ink-screen
An assistant to help you view text and picture calendars
56 parts33Apache-2.0
Questions
How big is the ESP32-DevKit Custom PCB?
It measures 30.4 × 56.5 mm and has 4 copper layers, 1.6 mm thick.
What parts does the ESP32-DevKit Custom use?
36 parts, built around the CP2102N-A01-GQFN28R, ESP32-WROOM-32D, AMS1117-3.3 and MMSS8050-H-TP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ESP32-DevKit Custom KiCad files?
From the chackojose2005-zodiac/ESP32-DevKit-Custom repository on GitHub, at the commit this page was made from: the board is ESP32-DevKit-Custom.kicad_pcb and its schematic ESP32-DevKit-Custom.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ESP32-DevKit Custom design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).