

BMS master hardware for bq76PL455A modules
- Size
- 93.5 × 53 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 57
- Nets
- 85
- Pads
- 235
- Tracks, vias
- 267, 17
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 23 Dec 2021
- Updated
- 29 Mar 2026
Overview
Ti bms is an open-source printed circuit board by catphish, from the catphish/ti-daisychain-bms repository on GitHub. It is a 2-layer board of 93.5 × 53 mm with 57 parts on 85 nets, routed with 267 tracks and 17 vias.
It is built around the ISL8485EIBZ, SN74LV1T34DBV and SN65HVD231D, with the TPS62160DGK, SM13072APEL and SS54 among its other parts. Its parts include 16 resistors, 12 capacitors, 8 ICs, 7 diodes and 5 connectors. It belongs with the power boards and the RP2040 boards of this library.
Main components
6ISL8485EIBZ
SOIC-8-40℃~+85℃ 1 1 10Mbps 4.5V~5.5V Transceiver SOIC-8 RS-485 / RS-422 ICs ROHSRenesas ElectronicsRS-485 / RS-422 ICsSN74LV1T34DBV
SOT-23-5-40℃~+125℃ 1 1 1.6V~5.5V 10uA 5.5ns@5V,15pF 74LV 8mA 8mA Level shifting Push-pull Unidirectional SOT-23-5 Buffers, Drivers, Receivers, Transceivers ROHSTexas InstrumentsBuffers, Drivers, Receivers, TransceiversSN65HVD231D
SOIC-8-40℃~+85℃ 17mA 1Mbps 1uA 3V~3.6V CAN Transceiver SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversTPS62160DGK
UncategorisedTexas InstrumentsSM13072APEL
SMD,12.8x6.9mm-40℃~+125℃ 1.5kV 1:1、1:1 350uH Single port 车规级 SMD,12.8x6.9mm Pulse Transformers(LAN) ROHSBournsPulse Transformers(LAN)SS54
SMA(DO-214AC)-55℃~+125℃ 1mA@40V 40V 550mV@5A 5A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky Diodes
README
READMETI Daisychain BMS Master
BMS master for daisychained bq76PL455A slave modules.
This board will communicate with up to 3 strings of bq76PL455A battery modules. Each string supports up to 16 modules, and each module supports up to 16 cells. A common configuration is 3 strings of 6 modules but any combination is supported.
The board will read the voltages of all detected cells and will perform balancing as well as reporting data over CAN.
Connector J1
| CANH | WAKE1 | WAKE2 | | CANL | GND | +12V |
The low voltage connector J1 has 3 functions:
- Connect +12v to a permanent positive suppy (5v - 14v)
- Connect CANH and CANL to a CAN bus.
- Connect WAKE1 and WAKE2 to switched voltage sources
If either WAKE1 OR WAKE2 is live (+5v to +14v) theh the board will wake up and monitor the pack. If both are off (0v) then the board will finish any in-progress balancing, then go into a low power sleep mode.
It is recommended to connect WAKE1 to ignition live, and WAKE2 to a 12V output generated by a charger. This will ensure that the cells are monitored during both charge and discharge.
Connector J2, J3, J4
Each of the BATT1, BATT2 and BATT3 (J2,J3,J4) may be connected to the data pins of a bq76PL455A battery module. All three are optional, and all three support a full chain of up to 16 battery modules, or any partial chain. Chain lengths do not have to be matched. The pinout of the battery module is beyong the scope of this document.
Power Modes
When either WAKE1 or WAKE2 are high, the module will enter active mode. In this mode, it will continuously monitor the voltage of all attached cells. Data including the pack voltage, high and low cell voltages, and temperatures will be send to the CAN bus at 1 second intervals. Balancing will take place if necessary. For further details of balancing see the next section.
When WAKE1 and WAKE2 are both low, and balancing is complete, the board will enter a low power sleep mode. In this mode, the board consumes approximately 600uA (0.6mA) at 12V and will perform no actions until woken again. The bq76PL455A modules will also anter a low power state, consuming close to zero power from the high voltage pack.
Balancing
If any cell voltage is detected as being higher than 4.0V and more than 10mV higher than the lowest recorded cell voltage, it will be bled until one of these ocnditions is no longer met. To prevent excessive heat, only one cell in each battery (16 cell module) will be bled simultaneously. If multiple cells meet the criteria, the cell with the highest voltage will be selected. Balancing will be considered complete when no cells meet the criteria for balancing.
CAN Messages Received
This modules does not receive CAN messages.
CAN Messages Sent
| CAN ID | Byte 0-3 | Byte 4-5 | Byte 6 | Byte 7 | | 0x4f0 | Total Pack Voltage | Balance Threshold | Error count | Module count |
Total pack voltage it the sum of all modules. For parallel packs this value will be a multiple of the real pack voltage.
Balance threshold will be a non-zero value when balancing is active and indicates the target voltage, generally this will be 10mV higher than the minimum cell voltage.
| CAN ID | Byte 0-1 | Byte 2-3 | Byte 4-5 | Byte 6-7 | | 0x4f1 | Max Cell V | Min Cell V | Max Cell Temp | Min Cell Temp |
All values are big endian. Voltage values should be interpreted by dividing the value by 13107. Temperature values are
The following calculation can be used to convert the readong for an External NTC to a temperature:
float temperature(uint16_t adc) { float r = 0.0000000347363427499292f * adc * adc - 0.001025770762903f * adc + 2.68235340614337f; float t = log(r) * -30.5280964239816f + 95.6841501312447f; return t; }
Parts
57| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100n | Capacitor_SMD:C_0603_1608Metric | C3, C4, C9, C10, C11, C15 |
| 4 | 10 | Resistor_SMD:R_0603_1608Metric | R3, R4, R7, R8 |
| 4 | 10n 1000v | Capacitor_SMD:C_1206_3216Metric | C5, C6, C7, C8 |
| 4 | 4k7 | Resistor_SMD:R_0603_1608Metric | R1, R2, R5, R6 |
| 4 | 5v | footprints:SOD882 | D1, D2, D3, D4 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3_Pad | H1, H2, H3, H4 |
| 2 | 3.3v | Diode_SMD:D_MiniMELF | D6, D9 |
| 2 | 47k | Resistor_SMD:R_0603_1608Metric | R13, R19 |
| 2 | 5.6k | Resistor_SMD:R_0603_1608Metric | R14, R20 |
| 2 | 51uH | footprints:ACT45B-101-2P-TL003 | L2, L3 |
| 2 | Conn_01x02 | Connector_Molex:Molex_Micro-Fit_3.0_43650-0200_1x02_P3.00mm_Horizontal | J2, J3 |
| 2 | ISL8485EIBZ | Package_SO:SOP-8_3.9x4.9mm_P1.27mm | U5, U6 |
| 2 | SN74LV1T34DBV | Package_TO_SOT_SMD:SOT-23-5 | U8, U9 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | 10u | Capacitor_SMD:C_1210_3225Metric | C1 |
| 1 | 120 | Resistor_SMD:R_1206_3216Metric | R12 |
| 1 | 147k | Resistor_SMD:R_0603_1608Metric | R10 |
| 1 | 2.2u | Inductor_SMD:L_Neosid_SMS-ME3015 | L1 |
| 1 | 22u | Capacitor_SMD:C_1206_3216Metric | C2 |
| 1 | 28k | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | CAN_TERM | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J6 |
| 1 | Conn_02x03_Odd_Even | Connector_Molex:Molex_Micro-Fit_3.0_43045-0600_2x03_P3.00mm_Horizontal | J1 |
| 1 | LOGO | footprints:sc | G*** |
| 1 | MCP2515-xST | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U2 |
| 1 | Pico | footprints:RPi_Pico_SMD_TH | U1 |
| 1 | SM13072APEL | Transformer_SMD:Transformer_Ethernet_Wuerth_749013011A | TR1 |
| 1 | SN65HVD231 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | SS54 | Diode_SMD:D_SMA | D5 |
| 1 | TPS62160DGK | Package_SO:MSOP-8_3x3mm_P0.65mm | U4 |
Similar boards
- 2 layers93.5 × 53 mm

- 2 layers87.5 × 70 mm

010 Implementation
NewTec-GmbH/esp32-can-iot
A ESP32 based interface between CAN-bus and IoT environments.
70 parts51BSD-3-Clause - 4 layers50 × 60 mm

Canarynode
aboller1212/canarynode
Custom CAN sensor node: STM32G474 + IMU + environmental, USB-C, 4-layer PCB
65 parts1 - 2 layers38 × 24.5 mm

3B LDO
AyushShuklaaa7/buck-ldo-5v-to-2v5-power-module
A custom PCB for dual-stage power regulator that combines the high efficiency of the TPS62160 Buck converter with TPS7A02 LDO. Designed for 5V input to 2.5V output applications.
23 parts - 2 layers140.5 × 106 mm

Pcbgalapagos
catuta0/HAB-payload
Carrier PCB for a high-altitude balloon payload. An ESP32 DevKitC V4 (WROOM-32) plugs into the board together with breakout modules for GPS (NEO-8M, I2C or UART header, fit only one), INA260 power monitor, BME280…
62 parts - 4 layers73 × 66 mm

ORCA First Linux Board
Finn254254/orca-one
Proprietary hardware files, schematics, PCB design, documentation and bring-up work for the Orca One V1.0 SBC.
106 parts - 2 layers140 × 90 mm

- 4 layers106 × 63.5 mm

Questions
How big is the Ti bms PCB?
It measures 93.5 × 53 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Ti bms use?
57 parts, built around the ISL8485EIBZ, SN74LV1T34DBV, SN65HVD231D and TPS62160DGK. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Ti bms KiCad files?
From the catphish/ti-daisychain-bms repository on GitHub, at the commit this page was made from: the board is hardware/ti-bms.kicad_pcb and its schematic hardware/ti-bms.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Ti bms design in my own project?
Its repository states no licence, so its author keeps all rights: ask catphish before reusing the design.