Skip to the content
2 layers54 × 54 mmImu splitter, the printed circuit board in 3D

Repository for the storage and dissemination of NN22 technical documents

Size
54 × 54 mm
Copper layers
2
Thickness
1.57 mm
Parts
16
Nets
25
Pads
87
Tracks, vias
125, 4
Pours
2
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
12 Feb 2024
Updated
18 Feb 2025

Overview

Imu splitter is an open-source printed circuit board by BUNPC, from the BUNPC/NN22-Technical-Documents repository on GitHub. It is a 2-layer board of 54 × 54 mm with 16 parts on 25 nets, routed with 125 tracks and 4 vias.

It is built around the AP2114H-3.3TRG1. Its parts include 9 connectors, 2 capacitors, 2 resistors, 2 diodes and 1 IC. It belongs with the sensors and measurement boards of this library.

Main components

1

README

Hardware Main/Electronics/Detector Electronics/DET_Splitter/README.md

readout-splitter

This is a splitter board designed to be plug-compatible with the TIGRIS one. See top-level README for some more details.

Connector from readout system is a Samtec SHF-117-01-L-D-SM shrouded 34-pin header with 0.05" pitch.

Detector connector is Samtec SFMC-118-02-S-D 36-pin socket strip with 0.05" pitch. Note that the TIGRIS schematic and layout use mirrored pinout for the detector connector (odd-even swap).

Designed LDOs:

  • Negative: ADP7182ACPZN-R7
  • Positive: ADP7142ACPZN5.0-R7

The negative adjustable regulator should output -15.0V with the resistors shown. There is an additional filter in the design (R+C on front side) which can (according to the datasheet) reduce the noise a bit in the negative regulator. There is no such provision for the positive regulator.

This is a 4-layer board and a bit dense. There were a few compromises made in routing with shared vias, etc but hopefully it will be OK.

Parts

16
QtyValueFootprintReferences
64P4Cmy_RJ:A-2004-3-4-LPJ1, J2, J3, J4, J5, J6
2LEDLED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolderD1, D2
11.5kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR1
110uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC1
122uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC2
13220-26-0200-00models:SAMTEC_SHF-113-01-L-D-RAJ7
1510Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderR2
1AP2114H-3.3TRG1Package_TO_SOT_SMD:SOT-223-3_TabPin2U1
1Conn_01x04Connector_PinHeader_1.27mm:PinHeader_1x04_P1.27mm_VerticalJ8
1Conn_01x05Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_VerticalJ9

More from BUNPC/NN22-Technical-Documents

7
  • 4 layers34.5 × 34.5 mmReadout splitter, the printed circuit board in 3D

    Readout splitter

    BUNPC/NN22-Technical-Documents

    Repository for the storage and dissemination of NN22 technical documents

    86 parts10
  • 2 layers122 × 122.3 mmTrigger board, the printed circuit board in 3D

    Trigger board

    BUNPC/NN22-Technical-Documents

    Repository for the storage and dissemination of NN22 technical documents

    70 parts10
  • 4 layers16 × 8 mmImu board, the printed circuit board in 3D

    Imu board

    BUNPC/NN22-Technical-Documents

    Repository for the storage and dissemination of NN22 technical documents

    10 parts10
  • 2 layers360 × 3.8 mmFlex VEMD, the printed circuit board in 3D

    Flex VEMD

    BUNPC/NN22-Technical-Documents

    Repository for the storage and dissemination of NN22 technical documents

    4 parts10
  • 2 layers29 × 21 mmImu adapter, the printed circuit board in 3D

    Imu adapter

    BUNPC/NN22-Technical-Documents

    Repository for the storage and dissemination of NN22 technical documents

    4 parts10
  • 2 layers34.5 × 34.5 mmSource splitter, the printed circuit board in 3D

    Source splitter

    BUNPC/NN22-Technical-Documents

    Repository for the storage and dissemination of NN22 technical documents

    3 parts10
  • 2 layers29.1 × 13.2 mmImu rj adapter, the printed circuit board in 3D

    Imu rj adapter

    BUNPC/NN22-Technical-Documents

    Repository for the storage and dissemination of NN22 technical documents

    2 parts10

Similar boards

  • 6 layers122 × 98 mmVNA, the printed circuit board in 3D

    VNA

    jankae/LibreVNA

    100kHz to 6GHz 2 port USB based VNA

    592 parts1.7kGPL-3.0
  • 6 layers100 × 70 mmSa800u baseboard hw, the printed circuit board in 3D

    Sa800u baseboard hw

    antmicro/snapdragon-845-baseboard

    https://antmicro.com/blog/2022/04/open-source-snapdragon-845-baseboard/

    616 parts70Apache-2.0
  • 2 layers65 × 56 mmAlpha, the printed circuit board in 3D

    Alpha

    jonnor/UnlockOslo

    Software-defined door control

    95 parts10MIT
  • 6 layers83.5 × 99.4 mmTAPRx888, the printed circuit board in 3D

    TAPRx888

    TAPR/TAPRx888

    The TAPR rx888 replacement board project

    225 parts6MIT
  • 2 layers35.8 × 34.2 mmJATAYU S3, the printed circuit board in 3D

    JATAYU S3

    Quadcoach/Jatayu

    JATAYU Flight Controller is an in-house, low-cost brushed drone flight controller being developed by The QU4D COACH.

    42 parts5
  • 4 layers100 × 50 mmChronolog, the printed circuit board in 3D

    Chronolog

    slemanz/chronolog

    STM32-based temperature data logger with RTC, NOR flash storage, LCD and Wi-Fi. Hardware and firmware.

    95 parts5
  • 6 layers100 × 100 mmBms board, the printed circuit board in 3D

    Bms board

    AerospaceNU/bms-pcb-design

    373 parts4
  • 2 layers90 × 98.5 mmIO Board, the printed circuit board in 3D

    IO Board

    FREILab/easyVerwaltungHardware

    Hardware und Firmware für alle Geräte im Bezug zu easyVerwaltung

    77 parts2

Questions

How big is the Imu splitter PCB?

It measures 54 × 54 mm and has 2 copper layers, 1.57 mm thick.

What parts does the Imu splitter use?

16 parts, built around the AP2114H-3.3TRG1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Imu splitter KiCad files?

From the BUNPC/NN22-Technical-Documents repository on GitHub, at the commit this page was made from: the board is IMU-bundle/ninjanirs-imu-main/KiCAD/(Delete) imu-splitter/imu-splitter.kicad_pcb and its schematic Hardware Main/Electronics/Detector Electronics/DET_Optode/flex-VEMD/flex-VEMD.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Imu splitter design in my own project?

Its repository states no licence, so its author keeps all rights: ask BUNPC before reusing the design.