

EXWatch retrodigital
A Retro Futuristic wrist watch inspired from nixie tube wrist watch.
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 18
- Nets
- 54
- Pads
- 126
- Tracks, vias
- 416, 15
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 11 Oct 2026
- Updated
- 29 Oct 2026
Overview
EXWatch retrodigital is an open-source printed circuit board by bsastudio601, from the bsastudio601/RetroDigitalWristWatchO1 repository on GitHub. It is a 4-layer board with 18 parts on 54 nets, routed with 416 tracks and 15 vias.
It is built around the KCSC02-105, 74HC595 and LIS3DH. Its parts include 8 ICs, 4 resistors and 2 capacitors. It belongs with the wearables boards and the ESP32 and RISC-V boards of this library.
Main components
3KCSC02-105
SMD-40℃~+85℃ 0.2 1 1.85V 10mm 3mm 6.9mm 7 Segment 75mW Common Cathode Red SMD LED Segment Displays ROHSKingbrightLED Segment Displays74HC595
SOP-16-40℃~+85℃ 1 100ns@5V,50pF 10MHz 2V~6V 74HC 8 Serial-to-Serial or Parallel Tri-State SOP-16 Shift Registers ROHSGRShift RegistersLIS3DH
LGA-16(3x3)-40℃~+85℃ 1.71V~3.6V 16bit 500nA Accelerometer Motion event detection SPI、I2C X,Y,Z ±16g LGA-16(3x3) Accelerometers ROHSSTMicroelectronicsAccelerometers
README
README.mdRetroDigitalWristWatchO1
A Retro Futuristic wrist watch inspired from nixie tube wrist watch.
CAD
The link to onshape file :
https://cad.onshape.com/documents/2ff11cee5ddfbc3f83090756/w/65dea8c705ea60074a3121a2/e/956382457094d7dfe0466492?renderMode=0&uiState=6ae2dc71c6980aea61bdc922total assembly

This is the look im aiming for !
case
this is the middle section or the main body of the watch

This is the bottom plate. the bottom plate has magnetic connector for charging

This is the top plate and its suppose to hold a 1 mm thick 40mm watch crystal.

PCB
THE PCB ! (took a few tries to get a decent routing for 2 layer pcb)

And the schematic

Assembly
The case is really precise and there in very little room for fancy connection system to put the case together im thinking to superrglue the top and glass to the body. there is going to be a grove to aling them. and same goes for the bottom but without the glue.
Firmware
Currently the firmware includes a really basic code to test the displays i need to get the components to update the code to work it properly with all the functions
BOM
| # | Component | Quantity |
|---|---|---|
| 1 | Seeed Studio XIAO ESP32-C3 | 1 |
| 2 | 0.2-inch single-digit SMD 7-segment display, common-cathode | 4 |
| 3 | 74HC595 shift register | 2 |
| 4 | LIS3DH 3-axis accelerometer | 1 |
| 5 | 1S LiPo battery | 1 |
| 6 | 4.7 kΩ resistor | 2 |
| 7 | 100 nF ceramic capacitor | 3 |
| 8 | 10 µF ceramic capacitor | 1 |
| 9 | magnetic connector 2 pin | 1 set |
| 10 | Custom 2-layer PCB | 1 |
| 11 | Watch case | 1 |
| 12 | Watch crystal/lens | 1 |
| 13 | 20 mm watch strap | 1 |
| 14 | Spring bars | 2 |
Conclusion
It was one of the hardest project for me because i had to learn Onshape and CAD from groundup. and the pcb routing took a few tries to make it work in 2 layer. But it was done with the help of gpt on helping me to choose right symbol in kicad and helping me navigate cad software.
Parts
18| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | KCSC02-105 | Display_7Segment:KCSC02-105 | U2, U3, U6, U7 |
| 4 | TestPoint | TestPoint:TestPoint_Pad_1.5x1.5mm | B-, B+, V-, V+ |
| 2 | 10K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R4 |
| 2 | 4.7K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 2 | 74HC595 | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U4, U5 |
| 1 | 0.1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2 |
| 1 | LIS3DH | Package_LGA:LGA-16_3x3mm_P0.5mm_LayoutBorder3x5y | U8 |
| 1 | XIAO-ESP32-C3-SMD | Seeed_Studio_XIAO_Series:XIAO-ESP32-C3-SMD | U1 |
Similar boards
- 2 layers482.6 × 35.6 mm

- 2 layers152.9 × 74.9 mm

- 2 layers196.7 × 31.5 mm

- 2 layers76.2 × 50.8 mm

- 4 layers109.8 × 145 mm

- 2 layers71.5 × 73.5 mm

Pomodoro
oguzmum/esp32-pomodoro
A Pomodoro timer built on an ESP32: 25 min focus, 5 min short break, and a 10 min long break every 4th cycle. Progress is shown on a TM1637 MM:SS display, a focus/break LED pair, a single 7-segment digit showing the…
11 parts - 4 layers51.9 × 108.5 mm

ESP 32 Battle 4h
samcwitte/PCB-Design-Battle
This is a repository containing my PCB designs for a 2-hour PCB battle I participated in with Predictable Designs on YouTube.
70 partsMIT - 2 layers75 × 52 mm

Questions
What parts does the EXWatch retrodigital use?
18 parts, built around the KCSC02-105, 74HC595 and LIS3DH. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the EXWatch retrodigital KiCad files?
From the bsastudio601/RetroDigitalWristWatchO1 repository on GitHub, at the commit this page was made from: the board is PCB/eXWatch_retrodigital.kicad_pcb and its schematic PCB/eXWatch_retrodigital.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the EXWatch retrodigital design in my own project?
Its repository states no licence, so its author keeps all rights: ask bsastudio601 before reusing the design.