
Txrx-1
brucemack/sdr2
This is a homebrew SDR rig with no dependency on external computers/soundcards/etc.

This is a homebrew SDR rig with no dependency on external computers/soundcards/etc.
Audio breakout is an open-source printed circuit board by brucemack, from the brucemack/sdr2 repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 76.3 × 41.5 mm with 46 parts on 41 nets, routed with 277 tracks and 37 vias.
It is built around the PCM5100PW. Its parts include 19 capacitors, 5 connectors, 2 resistors, 2 ICs and 1 inductor. It belongs with the audio and music and interfaces and adapters boards of this library.
This is a homebrew SDR rig with no dependency on external computers/soundcards/etc.

One-time setup of make process:
git submodule update --init
mkdir build
cd build
cmake -DPICO_BOARD=pico2 ..Command used to flash code to board:
~/git/openocd/src/openocd -s ~/git/openocd/tcl -f interface/cmsis-dap.cfg -f target/rp2350.cfg -c "adapter speed 5000" -c "rp2350.dap.core1 cortex_m reset_config sysresetreq" -c "program main.elf verify reset exit"GP0 - (Reserved for UART0 TX)
GP1 - (Reserved for UART0 RX)
GP2 -
GP3 -
GP4 - I2S SCK out to PCM1804 ADC and PCM5100 DAC
GP5 - RST out to PCM1804 ADC
GP6 - I2S DIN in from PC1804 ADC
GP7 - I2S BCK out to PC1804 ADC
GP8 - I2S LRCK out to PC1804 ADC
GP9 - I2S DOUT out to PCM5100 DAC
GP10 - I2S BCK out to PCM5100 DAC
GP11 - I2S LRCK out to PCM5100 DAC
GP12 - User button input 0
GP13 - User button input 1
GP14 - PTT input
GP15 -
GP16 - I2C0 SDA for Si5351 (Addr 0x60)
GP17 - I2C0 SCL for Si5351 (Addr 0x60)
GP18 - I2C1 SDA for display and IO expander
GP19 - I2C1 SCL for display and IO expanderP0 - User indicator LED output
P1 - Audio amplifier enable (Low=enable output, high=shutdown amplifier)
P2 - ADC Input Select (Low=Microphone preamp out, High=QSD channel out)
P3 - TX band select 0
P4 - TX band select 1
P5 - RX band select 0
P6 - RX band select 1
P7 - Transmit PA enable (active low)See Horowitz and Hill (3rd ed, section 5.16, figure 5.88) for a description of the instrumentation amplifier configuration used on the receive board. Gain for this amplifier is controlled determined by 1 + 2 Rf / Rg. Notice that the feedback path is tapped after a 47 ohm resistor to set the output impedance of the stage.
Assuming Rf is 520, Rg is 100, the theoretical gain is about 11.
dBm = 30 + 20 * log(Vrms/sqrt(Z0))
Consider the PCM1863 ADC?
Consider the TS5A4624 analog switch (logic high = 2.4V w/ 5V supply)
Consider PCF8574A IO expander: https://www.ti.com/lit/ds/symlink/pcf8574a.pdf?ts=1728869550852&ref_url=https%253A%252F%252Fwww.mouser.com%252F
RF Transistor: https://www.nxp.com/docs/en/data-sheet/BFU590G.pdf
PCM1804 Datasheet PCM5100 Datasheet
The library gets built once in a parallel project:
cd ~/pico
mkdir CMSISDSP
cd CMSISDSP
git clone https://github.com/ARM-software/CMSIS-DSP.git
git clone https://github.com/ARM-software/CMSIS_6.git
cp $PICO_SDK_PATH/external/pico_sdk_import.cmake .Then setup the CMakeLists.txt shown below and build:
mkdir build
cd build
# IMPORTANT! pico2 build enables the generation of FPU instructions
cmake -DPICO_BOARD=pico2 ..
make -j4What the CMakeLists.txt looks like:
cmake_minimum_required (VERSION 3.6)
# Pull in Pico SDK (must be before project)
include(pico_sdk_import.cmake)
set(HOME $ENV{HOME})
set(CMSISDSP ${HOME}/pico/CMSISDSP/CMSIS-DSP)
set(CMSISCORE ${HOME}/pico/CMSISDSP/CMSIS_6/CMSIS/Core)
# Define the project
project (cmsis-dsp VERSION 0.1)
# Initialise the Pico SDK
pico_sdk_init()
add_subdirectory(${CMSISDSP}/Source bin_dsp)
target_compile_options(CMSISDSP PUBLIC
-Wsign-compare
-Wdouble-promotion
-Ofast -ffast-math
-DNDEBUG
-Wall -Wextra -Werror
-fshort-enums
#-fshort-wchar
)Example of referencing the built CMSIS-DSP library in a client project:
set(HOME $ENV{HOME})
target_include_directories(main PRIVATE
${HOME}/pico/CMSISDSP/CMSIS-DSP/Include
${HOME}/pico/CMSISDSP/CMSIS_6/CMSIS/Core/Include
)
target_link_libraries(main
pico_stdlib
${HOME}/pico/CMSISDSP/build/bin_dsp/libCMSISDSP.a
)SDR2 Rig - Copyright (C) Bruce MacKinnon KC1FSZ, 2025
This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program. If not, see https://www.gnu.org/licenses/.
FOR AMATEUR RADIO USE ONLY. NOT FOR COMMERCIAL USE WITHOUT PERMISSION.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | SolderJumper_3_Bridged12 | Jumper:SolderJumper-3_P1.3mm_Bridged12_Pad1.0x1.5mm | JP1, JP2, JP3, JP4, JP8, JP9, JP10, JP11, JP12, JP13 |
| 4 | 0.1u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C11, C14, C17, C19 |
| 4 | 0.1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C4, C7 |
| 4 | 10u | Capacitor_THT:CP_Radial_D4.0mm_P2.00mm | C10, C13, C16, C18 |
| 4 | MountingHole | MountingHole:MountingHole_3.5mm | H1, H2, H3, H4 |
| 3 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP5, JP6, JP7 |
| 2 | 1u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C12, C15 |
| 2 | 2.2nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C8, C9 |
| 2 | 2.2uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C5 |
| 2 | 470 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
| 2 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J4, J5 |
| 1 | 10uF | Capacitor_THT:CP_Radial_D4.0mm_P2.00mm | C6 |
| 1 | 47u | Inductor_SMD:L_0805_2012Metric_Pad1.15x1.40mm_HandSolder | L1 |
| 1 | Conn_01x03 | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J1 |
| 1 | Conn_01x04 | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J2 |
| 1 | Conn_01x05 | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J3 |
| 1 | PCM1804DBR | Package_SO:SSOP-28_5.3x10.2mm_P0.65mm | U2 |
| 1 | PCM5100 | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U1 |

brucemack/sdr2
This is a homebrew SDR rig with no dependency on external computers/soundcards/etc.

brucemack/sdr2
This is a homebrew SDR rig with no dependency on external computers/soundcards/etc.

brucemack/sdr2
This is a homebrew SDR rig with no dependency on external computers/soundcards/etc.

brucemack/sdr2
This is a homebrew SDR rig with no dependency on external computers/soundcards/etc.

brucemack/sdr2
This is a homebrew SDR rig with no dependency on external computers/soundcards/etc.

brucemack/sdr2
This is a homebrew SDR rig with no dependency on external computers/soundcards/etc.

polpo/picogus
Emulation of ISA sound cards and CD-ROM on Raspberry Pi Pico (GUS, SB/Adlib, MPU-401, Tandy, CMS, Panasonic CD-ROM) with USB mouse/joystick support


intergalaktik/Extension_Boards_for_Olimex_GateMate
Simple extension boards for Olimex GateMate FPGA Board

saybur/dac-attack
S/PDIF to line-level audio board for use with retro computer device emulators, such as ZuluSCSI and friends.


mbeayou/esp32-hifi-bluetooth-speaker-pcb-board
A custom high-fidelity Bluetooth speaker PCB featuring the ESP32 (I2S), PCM5100 DAC, and TPA3116D2 Class D Amplifier. Includes Schematics, Gerber files, and BOM.

sparkfun/SparkFun_Qwiic_WAV_Trigger_Pro
An STM based WAV/MIDI device with a full speed USB interface.

It measures 76.3 × 41.5 mm and has 2 copper layers, 1.6 mm thick.
46 parts, built around the PCM5100PW. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the brucemack/sdr2 repository on GitHub, at the commit this page was made from: the board is hw/audio-breakout/audio-breakout.kicad_pcb and its schematic hw/audio-breakout/adc.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).