
Video Buffer RevB
BrettHallen/Conversion_Boards
Various boards to convert from one chip to another

Various boards to convert from one chip to another
Soviet Keyswitch Replacement is an open-source printed circuit board by BrettHallen, from the BrettHallen/Conversion_Boards repository on GitHub. It is a 2-layer board of 69 × 16.4 mm with 8 parts on 8 nets, routed with 24 tracks and 0 vias.
Various boards to convert from one chip to another. Unless stated otherwise, they are currently untested.
A breakout board for the 5-pin DIN plug on this tri-voltage Mean Well PSU.
Breakout boards to simplify connecting various ICs to a logic analyser via Dupoint-style wires:
YouTube Videos:
Breakout boards for various D-sub type connectors:
Boards to convert between different ROM/PROM/EPROM types:
A breakout board for 5/6/7/8 pin DIN connectors.
Idea is to use a surface mount crystal in place of the through-hole crystal. Why? Spectrum clones from the former Eastern Bloc tended to use 14MHz crystals which are not easy to come by anymore in through-hole form, but surface mount versions are.
20-Jun-2025: Test boards have been fabricated, not yet tested.
Soviet-era electronics used a 2.5mm pin pitch rather than 2.54mm/0.1" pin pitch we are accustomed to in the West. This can cause problems with larger chips as they need to be bent slightly to fit. Hence this idea to allow a Western chip to fit into a Soviet motherboard, like an Intel 8080A to replace a Soviet КР580ВМ80А.
20-Jun-2025: Test boards have been fabricated, not yet tested.

The idea behind this design is to make a 2.5mm pin pitch IC socket for Soviet-era chips.
20-Jun-2025: Test boards have been fabricated, not yet tested.

Replacement designs for Soviet-era VM16 key switches.
26-Jul-2025: Initial PCB tested, requires adjustments

A board to bring out the pins of a 64-pin IC with 1.27mm pin-pitch (like the Yamaha V99x8 VDPs) to 2.54mm pin-pitch headers so it can be hooked up for experimenting with similarly-minded 2.54mm pitch stuff.

A very simple transistor buffer for converting RF-modulated video output to baseband video output by taking the video signal generated by the computer before it reaches the RF modulator can and passing it through an emitter follower.
Based on the design for the Sinclair ZX81 but could be used for other "quick 'n' dirty" mods to see if a computer is working.

| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | Cherry_MX | PCM_Switch_Keyboard_Cherry_MX:SW_Cherry_MX_PCB | SW2, SW4, SW6, SW8 |
| 4 | Soviet_VM16 | Clueless_Engineer:VM16_Keyswitch | SW1, SW3, SW5, SW7 |

BrettHallen/Conversion_Boards
Various boards to convert from one chip to another


BrettHallen/Conversion_Boards
Various boards to convert from one chip to another

BrettHallen/Conversion_Boards
Various boards to convert from one chip to another


BrettHallen/Conversion_Boards
Various boards to convert from one chip to another


BrettHallen/Conversion_Boards
Various boards to convert from one chip to another

BrettHallen/Conversion_Boards
Various boards to convert from one chip to another

BrettHallen/Conversion_Boards
Various boards to convert from one chip to another

BrettHallen/Conversion_Boards
Various boards to convert from one chip to another

BrettHallen/Conversion_Boards
Various boards to convert from one chip to another


joeycastillo/Sensor-Watch
A board replacement for the classic Casio F-91W wristwatch

rusefi/rusefi
rusefi - GPL internal combustion engine control unit

hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

shanteacontrols/OpenDeck
A platform for building interactive control and sensing devices using MIDI and OSC built with Zephyr RTOS.

hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

dangiu/PicoMemcard
Emulating PSX Memory Card (or controller) using a Raspberry Pi Pico

OLIMEX/DIY-LAPTOP
Do It Yourself Open Source Hardware and Software Modular Hacker's Friendly Laptop
It measures 69 × 16.4 mm and has 2 copper layers, 1.6 mm thick.
8 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the BrettHallen/Conversion_Boards repository on GitHub, at the commit this page was made from: the board is Soviet-Keyswitch-Replacement/Soviet_Keyswitch_Replacement.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask BrettHallen before reusing the design.