

ISA-26-TESTER KIT COMMUNITY
- Size
- 225.3 × 126.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 30
- Nets
- 36
- Pads
- 114
- Tracks, vias
- 226, 0
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 4 Aug 2026
- Updated
- 3 Sep 2026
Overview
ISA-26-TESTER KIT COMMUNITY is an open-source printed circuit board by bottlecoder-raj, from the bottlecoder-raj/ISA-26-TESTER-KIT-COMMUNITY repository on GitHub. It is a 2-layer board of 225.3 × 126.5 mm with 30 parts on 36 nets, routed with 226 tracks and 0 vias.
It is built around the DHT11. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
1README
README.mdISA-26-TESTER-KIT-COMMUNITY
Parts
30| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | Conn_01x01_Pin | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J4, J18, J19, J20, J21, J22, J23, J24, J25, J26, J27 |
| 1 | 0.96" Oled | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J9 |
| 1 | 3V3/5V | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | POWER_PLUG1 |
| 1 | 4x4 Keypad | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J15 |
| 1 | Arduino_Nano_v2.x | Module:Arduino_Nano | A1 |
| 1 | Buzzer | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | BZ1 |
| 1 | DHT11 | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J7 |
| 1 | GAS | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J11 |
| 1 | Hall Effect | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J13 |
| 1 | I2C 16X2 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | Joystick | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J16 |
| 1 | LDR/IR | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J10 |
| 1 | MOTOR | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J17 |
| 1 | MPU6050 | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J14 |
| 1 | PIR | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J12 |
| 1 | RFID | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J1 |
| 1 | Servo | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J5 |
| 1 | TEST_PIN | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J8 |
| 1 | TX/RX | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | Ultrasonic sensor | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J6 |
Similar boards
- 2 layers96.6 × 82.8 mm

- 2 layers100 × 50 mm

Conveyor belt pcb
lansidev/conveyor-belt
Miniature 3D printed conveyor belt for simulation and fun working with sensors, all controllable with Raspberry Pi
22 parts9MIT - 2 layers93 × 20 mm

- 2 layers

OpenMQTTGatewayPCB
ebrithiljonas/OMG_PCB
All in One PCB for the OpenMQTTGateway Project
36 parts7GPL-3.0 - 2 layers62 × 19.3 mm

SniffingTrinket
GeorgK/SniffingTrinket
A room climate monitor using the Adafruit Trinket Pro
23 parts6GPL-3.0 - 2 layers

Arduino relay
bhaskar9980/Guardian
Guardian is an advanced, fully automated hydroponics system designed to optimize plant growth and maximize yield.
58 parts5MIT - 2 layers100 × 43.5 mm

Firefly
Twistx77/Firefly
Open WIFI-enabled RGB lamp with temperature, humidity, suspended air particles and eCO2 sensors.
33 parts5GPL-3.0 - 2 layers30.5 × 77.5 mm

Proyecto sensor temperatura
unla-investigacion-desarrollo/ecosistema-iot
Antes de desarrollar el sistema final, realizamos una etapa de exploración donde investigamos y experimentamos con las siguientes tecnologías:
8 parts5
Questions
How big is the ISA-26-TESTER KIT COMMUNITY PCB?
It measures 225.3 × 126.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ISA-26-TESTER KIT COMMUNITY use?
30 parts, built around the DHT11. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ISA-26-TESTER KIT COMMUNITY KiCad files?
From the bottlecoder-raj/ISA-26-TESTER-KIT-COMMUNITY repository on GitHub, at the commit this page was made from: the board is A4/A4.kicad_pcb and its schematic A4/A4.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ISA-26-TESTER KIT COMMUNITY design in my own project?
Its repository states no licence, so its author keeps all rights: ask bottlecoder-raj before reusing the design.