

CanCape
A 3D printer tool head controller board
- Size
- 83.8 × 20 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 21
- Nets
- 6
- Pads
- 82
- Tracks, vias
- 63, 6
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 25 Mar 2020
- Updated
- 10 Dec 2022
Overview
CanCape is an open-source printed circuit board by bondus, from the bondus/KlipperToolboard repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 83.8 × 20 mm with 21 parts on 6 nets, routed with 63 tracks and 6 vias.
Its parts include 16 connectors, 2 resistors and 1 fuse. It belongs with the robots and motor control boards of this library.
README
README.mdHuvud 3D Printer toolhead board
A very small 3D printer board for use on a direct drive toolhead. It is designed to be used with Klipper firmware. Klipper has the awesome feature to be able to use multiple MCUs connected to the host over a (relatively) high latency connection. Using CAN bus it is possible to chain many boards using just a pair of twisted wires and power. A good solution for multiple head 3D printers.

Features:
- CAN bus.
- One TMC2209 stepper driver for the extruder
- Two MOSFETs for fans
- One big MOSFET for the hotend heater
- Thermistor input
- Support for an endstop (or filament runout sensnor)
- STM32F103 72Mhz 32bit ARM MCU
- USB, for flashing firmware
Main power is 12-24V. 24V is preferred to keep the currents low
All done in KiCad and open source.
If you are interesting in helping out, testing or eventually using this board feel free to contact me at glpontus@gmail.com.
Documentation
Buy it at:
- Lukes Lab: https://lukeslabonline.com/products/huvud
- Tindie: https://www.tindie.com/products/huvud/huvud-3d-printer-hotend-control-board/
Read more about the project activites over at hackaday: https://hackaday.io/project/174429-huvud-a-3d-printer-tool-head-controller-board
Parts
21| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | Conn_01x01 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J8, J9, J12, J13 |
| 4 | Conn_02x02_Top_Bottom | Connector_Molex:Molex_Micro-Fit_3.0_43045-0412_2x02_P3.00mm_Vertical | J2, J3, J4, J5 |
| 4 | Conn_02x02_Top_Bottom | Connector_Molex:Molex_Micro-Fit_3.0_43045-0400_2x02_P3.00mm_Horizontal | J11, J14, J15, J16 |
| 2 | Conn_01x02 | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J6, J7 |
| 2 | MountingHole | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H2 |
| 1 | 120R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2 |
| 1 | 120R | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | Conn_01x02 | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J1 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J10 |
| 1 | Fuse | cancape:KEYSTONE-3568 | F2 |
More from bondus/KlipperToolboard
6- 4 layers42 × 42 mm

- 4 layers42 × 42 mm

- 4 layers45 × 48 mm

- 2 layers37 × 15 mm

- 2 layers65 × 56.5 mm

- 2 layers65 × 30 mm

Similar boards
- 2 layers28.3 × 39.8 mm

LevelShifter
gusmanb/logicanalyzer
24 channel, 100Msps logic analyzer hardware and software
21 parts5.1kGPL-3.0 - 2 layers171.2 × 72.9 mm

Amiga gfxcard before pour
mntmn/amiga2000-gfxcard
MNT VA2000, an Open Source Amiga 2/3/4000 Graphics Card (Zorro II/III), written in Verilog
21 parts1k - 2 layers93.9 × 46 mm

- 2 layers45.5 × 42.9 mm

Esphome han reader
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
21 parts915 - 2 layers31.8 × 14.5 mm

Esp prog
drandyhaas/KiCadRoutingTools
A set of Python/Rust tools to aid routing in KiCad
21 parts744MIT - 2 layers23.5 × 15.8 mm

QuiverAttachPCB
Arrow-air/project-quiver
Project Quiver documentation, designs, and project artifacts.
21 parts617CERN-OHL-S-2.0 - 2 layers69.9 × 41.3 mm

- 2 layers161.3 × 111.8 mm

Questions
How big is the CanCape PCB?
It measures 83.8 × 20 mm and has 2 copper layers, 1.6 mm thick.
What parts does the CanCape use?
21 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the CanCape KiCad files?
From the bondus/KlipperToolboard repository on GitHub, at the commit this page was made from: the board is PCB/CanDist/CanCape.kicad_pcb and its schematic PCB/HuvudTiny2/Huvud.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the CanCape design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).