Skip to the content
2 layers173.4 × 161.4 mmExtraDox Left, the printed circuit board in 3D

An ergonomic custom keyboard design inspired by the ErgoDox

Size
173.4 × 161.4 mm
Copper layers
2
Thickness
1.6 mm
Parts
121
Nets
82
Pads
486
Tracks, vias
646, 92
Pours
2
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
6 Dec 2022
Updated
22 Apr 2026

Overview

ExtraDox Left is an open-source printed circuit board by blastrock, from the blastrock/ExtraDox repository on GitHub. It is a 2-layer board of 173.4 × 161.4 mm with 121 parts on 82 nets, routed with 646 tracks and 92 vias.

It is built around the PCA9555PW. Its parts include 45 diodes, 45 switches, 18 resistors, 4 capacitors and 1 IC. It belongs with the keyboards and input boards of this library.

Main components

1

README

README.md

ExtraDox (v2)

The ExtraDox

The ExtraDox is a split keyboard based off the ErgoDox. The main difference is that it has an additional row of keys on the top. Also, it is a low-profile keyboard designed for Choc v1 switches.

It features:

  • An additional row of keys over the ErgoDox
  • An USB-C port
  • A single-board design (actually two boards), no extra controller board
  • A TRRS connection between the two sides
  • The 3 usual status LED
  • The case is only 8mm thick, the keys are 18mm high from the desk

What you need to build this keyboard

  • The PCBs and their components (the MCU is soldered on the main board)
  • The 3D-printed case
  • 14x M2.5x8 screws and nuts
  • 10x rubber pads to put under the keyboard to prevent slipping
  • 90x Kailh Choc Hotswap sockets
  • 90x Kailh Choc switches
  • 82x 1u key caps
  • 4x 1.5u key caps
  • 4x 2u key caps
  • 3x SMD status LED (see the Kicad project for details)
  • 2x TRRS connector (see the Kicad project for details)
  • 1x TRRS cable
  • 1x USB-c cable

About this keyboard

PCB

The PCB is designed in Kicad. It is a SMD design and the project includes component references from JLCPCB.

Case

The case is designed to be 3D-printed. The case is screwed together with 7 M2.5x8 screws on each side, and their corresponding bolts.

Firmware

Here is a a fork of the QMK firmware with support for the ExtraDox.

Known issues

Some capacitors are located right under an hotswap socket. It is still possible to solder it, but the socket gets a little tilted.

License

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.

Parts

121
QtyValueFootprintReferences
45DDiode_SMD:D_SOD-123FD10, D11, D12, D13, D14, D15, D16, D20, D21, D22, D23, D24, D25, D26, D27, D28 +29
41SW_Pushadditional-footprints:KailhHotswapChoc1SW0:1, SW0:4, SW0:5, SW0:6, SW1:0, SW1:1, SW1:2, SW1:3, SW1:4, SW2:0, SW2:1, SW2:2, SW2:3, SW2:4, SW2:5, SW3:0 +25
14470Resistor_SMD:R_0402_1005MetricR11, R12, R16, R17, R18, R19, R20, R21, R22, R23, R24, R25, R26, R27
20.1uFCapacitor_SMD:C_0402_1005MetricC7, C8
2100Resistor_SMD:R_0402_1005MetricR7, R8
22.2kResistor_SMD:R_0402_1005MetricR9, R10
2SW_Pushadditional-footprints:KailhHotswapChoc15SW2:6, SW4:6
2SW_Pushadditional-footprints:KailhHotswapChoc2SW0:2, SW0:3
110uFCapacitor_SMD:C_0402_1005MetricC5
11uFCapacitor_SMD:C_0402_1005MetricC6
1PCA9555PWadditional-footprints:TSSOP-24_4.4x7.8mm_P0.65mm_JLCPCBU1
1TRRSadditional-footprints:TRRS-PJ-320AJ2

The 114 most common of 121 parts.

More from blastrock/ExtraDox

1
  • 2 layers173.4 × 161.4 mmExtraDox Right, the printed circuit board in 3D

    ExtraDox Right

    blastrock/ExtraDox

    An ergonomic custom keyboard design inspired by the ErgoDox

    140 parts45

Similar boards

  • 2 layers243.2 × 106 mm3W6, the printed circuit board in 3D

    3W6

    weteor/3W6

    a small compact 3x5+3 split ortho keyboard

    113 parts488
  • 2 layers199.5 × 100.5 mmSPC EVDR, the printed circuit board in 3D

    SPC EVDR

    weteor/SPC_EVDR

    38 key otholinear keyboard with offset spacebar(s)

    93 parts59CERN-OHL-P-2.0
  • 2 layers100 × 50 mmXiamocon, the printed circuit board in 3D

    Xiamocon

    shapoco/xiamocon

    Game Console-Shaped Motherboard for XIAO RP2350/ESP32S3

    111 parts39
  • 2 layers100 × 50 mmShapones xiao rp2350, the printed circuit board in 3D

    Shapones xiao rp2350

    shapoco/shapones

    an NES emulator for programming study.

    75 parts37
  • 4 layers61.8 × 79.6 mmShipwrecked pcb, the printed circuit board in 3D

    Shipwrecked pcb

    mpkendall/shipwrecked-pcb

    Shipwrecked PCB Badges

    153 parts17Unlicense
  • 2 layers128 × 103.8 mmPhase, the printed circuit board in 3D

    Phase

    mjpauly/phase

    42-key split keyboard inspired by Corne, Kyria, and Ferris

    70 parts15
  • 2 layers100 × 97.5 mmMC5000 Board, the printed circuit board in 3D

    MC5000 Board

    RickP/MC5000_DevKit

    An hardware puzzle that teaches the basics of programming.

    131 parts6GPL-3.0
  • 2 layers90 × 100 mmHost shell, the printed circuit board in 3D

    Host shell

    shapoco/wildcardboy

    Handheld Game Console with Replaceable MCU

    241 parts5

Questions

How big is the ExtraDox Left PCB?

It measures 173.4 × 161.4 mm and has 2 copper layers, 1.6 mm thick.

What parts does the ExtraDox Left use?

121 parts, built around the PCA9555PW. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ExtraDox Left KiCad files?

From the blastrock/ExtraDox repository on GitHub, at the commit this page was made from: the board is PCB/Left/ExtraDox-Left.kicad_pcb and its schematic PCB/Left/ExtraDox-Left.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the ExtraDox Left design in my own project?

Its repository states no licence, so its author keeps all rights: ask blastrock before reusing the design.