Skip to the content
2 layers82 × 22.5 mmFM Radio, the printed circuit board in 3D

In FM, the instantaneous frequency varies with the audio signal m(t):

Size
82 × 22.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
17
Nets
11
Pads
40
Tracks, vias
114, 2
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
10 Aug 2025
Updated
10 Aug 2025

Overview

FM Radio is an open-source printed circuit board by bejaouihamza, from the bejaouihamza/FM_Radio repository on GitHub. It is a 2-layer board of 82 × 22.5 mm with 17 parts on 11 nets, routed with 114 tracks and 2 vias.

It is built around the LM386. Its parts include 7 capacitors, 2 transistors, 1 resistor, 1 IC and 1 connector. It belongs with the radio and wireless boards of this library.

Main components

1

README

README.md

📻 FM Radio Receiver – Technical Overview

FM Radio Schematic

📑 Introduction

This project is a simple FM radio receiver built using analog components and an RF tuner stage.
It demonstrates the principles of frequency modulation (FM) reception, the electromagnetic theory,
and the electronics needed to detect and play broadcast FM audio.


📷 Schematic

FM Radio Schematic


⚡ How FM Radio Works

FM (Frequency Modulation) encodes audio into a radio wave by varying its frequency
while keeping the amplitude constant.

Electromagnetic Principle

  • FM signals are electromagnetic waves traveling at the speed of light (c = 3×10⁸ m/s).
  • A broadcast station transmits a carrier frequency in the VHF band (88–108 MHz).
  • The antenna captures a small portion of this wave and converts it into a weak AC signal.
  • The circuit processes this to recover the original audio waveform.

📐 The Math Behind FM

If the carrier wave is:

c(t) = Ac · cos( 2π fc t )

In FM, the instantaneous frequency varies with the audio signal m(t):

s(t) = Ac · cos[ 2π fc t + β · sin( 2π fm t ) ]

Where:

  • fm = maximum frequency of the audio signal
  • β = modulation index = Δf / fm
  • Δf = frequency deviation (max shift from fc)

Typical broadcast values:

  • Δf ≈ 75 kHz
  • fm ≤ 15 kHz

🔧 Circuit Overview

1. Antenna & LC Tuner
Captures the FM signal and selects the desired frequency using:

fres = 1 / ( 2π √(LC) )

2. RF Amplifier
Boosts the weak signal without adding too much noise.

3. Mixer & Local Oscillator
Shifts the RF signal to an Intermediate Frequency (IF) (10.7 MHz).

4. IF Amplifier & Limiter
Amplifies and removes amplitude variations (FM carries info in frequency only).

5. FM Demodulator
Converts frequency changes into voltage variations (audio signal).

6. Audio Amplifier
Boosts the audio to drive a speaker.


📊 Signal Flow

mermaid
graph LR
    A[Antenna] --> B[LC Tuned Circuit]
    B --> C[RF Amplifier]
    C --> D[Mixer]
    E[Local Oscillator] --> D
    D --> F[IF Filter]
    F --> G[IF Amplifier]
    G --> H[Limiter]
    H --> I[FM Discriminator]
    I --> J[Audio Amplifier]
    J --> K[Speaker]

Parts

17
QtyValueFootprintReferences
2100nCapacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mmC6, C7
2220uCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC2, C5
2NPNPackage_TO_SOT_THT:TO-92_InlineQ1, Q2
1(1.8-30)pfCapacitor_SMD:C_Trimmer_Murata_TZB4-AC3
10.05uCapacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mmC1
10.1uInductor_THT:L_Axial_L11.0mm_D4.5mm_P15.24mm_Horizontal_Fastron_MECCL1
110Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR2
110kPotentiometer_THT:Potentiometer_Alps_RK09Y11_Single_HorizontalRV1
110uCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC4
1AntennaRF_Antenna:NiceRF_SW868-TH13_868MhzAE1
1LM386Package_DIP:DIP-8_W7.62mmU1
1LOGOLOGOG***
1Screw_Terminal_01x02TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_HorizontalJ1
1Speakerfootprints:SPKR_AST-1732MR-RLS1

Similar boards

  • 2 layers152 × 88 mmRFBitBangSMT, the printed circuit board in 3D

    RFBitBangSMT

    profdc9/RFBitBanger

    A QRP digital transceiver created from readily available parts for off-the-grid maintenance

    271 parts222
  • 2 layers90 × 140 mmDrumkid, the printed circuit board in 3D

    Drumkid

    mattybrad/drumkid

    Version 4 was the first successful working design, with full code, schematics, Gerbers, etc available on GitHub.

    70 parts137
  • 2 layersLM80C R6, the printed circuit board in 3D

    LM80C R6

    leomil72/LM80C

    A Z80-based homebrew computer withTMS9918, AY-3-8910, Z80 CTC, Z80 PIO, and Z80 SIO

    153 parts123GPL-3.0
  • 2 layers145.3 × 44.5 mmScout, the printed circuit board in 3D

    Scout

    oskitone/scout

    3D-printed, Arduino-compatible, 17-key mono synth. Squeeeee!

    48 parts114
  • 2 layers184 × 114.8 mmPoly555, the printed circuit board in 3D

    Poly555

    oskitone/poly555

    The POLY555 is a polyphonic, analog, square wave synth based on the 555 timer chip.

    262 parts93
  • 4 layers223.3 × 120.1 mmISA FPGA v2, the printed circuit board in 3D

    ISA FPGA v2

    robfinch/Cores

    Cores ===== RTF's Cores Use at your own risk. Welcome to my galaxy of cores. Contained in the directories are IP cores, source code for digital circuits.

    132 parts78
  • 2 layers101.6 × 137.4 mmOpenxcvr, the printed circuit board in 3D

    Openxcvr

    dawsonjon/OpenXcvr

    Cost Effective HF transceiver based on max1000 FPGA module

    155 parts38MIT
  • 2 layers104.1 × 73.7 mmIsa opl2, the printed circuit board in 3D

    Isa opl2

    skiselev/isa-opl2

    ISA OPL2 Card

    61 parts36

Questions

How big is the FM Radio PCB?

It measures 82 × 22.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the FM Radio use?

17 parts, built around the LM386. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the FM Radio KiCad files?

From the bejaouihamza/FM_Radio repository on GitHub, at the commit this page was made from: the board is fm-radio.kicad_pcb and its schematic fm-radio.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the FM Radio design in my own project?

Its repository states no licence, so its author keeps all rights: ask bejaouihamza before reusing the design.