4 layers180.8 × 300.3 mm
Dilemma
Bastardkb/Dilemma
The Dilemma is a vertical stagger low-profile keyboard with mods.
383 parts590
2 layers41.6 × 77.6 mm
Splinktegrated
Bastardkb/splinktegrated49The splinktegrated is a board made for dactyls.
- Size
- 41.6 × 77.6 mm
- Copper layers
- 2
- Thickness
- 1.2 mm
- Parts
- 61
- Nets
- 73
- Pads
- 273
- Tracks, vias
- 855, 91
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 14 Dec 2022
- Updated
- 10 Sep 2026
Overview
Splinktegrated is an open-source printed circuit board by Bastardkb, from the Bastardkb/splinktegrated repository on GitHub. It is a 2-layer board of 41.6 × 77.6 mm with 61 parts on 73 nets, routed with 855 tracks and 91 vias.
It is built around the RP2040, W25Q128JVSIQ and USBLC6-2P6, with the XC6210B332MR-G among its other parts. Its parts include 14 capacitors, 13 connectors, 11 resistors, 5 ICs and 2 diodes. It belongs with the RP2040 boards of this library.
Main components
4
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
USBLC6-2P6
SOT-666-6-40℃~+125℃ 150nA 17V 2 3.5pF 5.25V 5A@8/20us 6V ESD IEC 61000-4-2 Unidirectional SOT-666-6 ESD and Surge Protection (TVS/ESD) ROHSSTMicroelectronicsESD And Surge Protection (TVS/ESD)
XC6210B332MR-G
SOT-25-5-40℃~+85℃@(Ta) 1 100mV@(200mA) 3.3V 55uA 60dB@(1kHz) 6V 700mA Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-25-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
readme.mdSplinktegrated
The splinktegrated is a board made for dactyls.
It is based on the 0xB2 Splinky by plut0nium.
Features:
- designed for assembly with off-the-shelf components at JLC
- connectors for up to 5 rows and 6 columns
- connectors for a trackball
- 2 holes for M4 screws
- ESD protection on USB and serial line
- 16MB memory
- footprint for audio jack and reset button
- reversible, with a jumper for power
How to order:
- grab the latest gerber/bom/pos files in the release section
- those are made to be ordered at JLCPCB
- order in standard 1.6mm thickness
License
CERN Open Hardware Licence Version 2 - Strongly Reciprocal
Parts
61| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 100n | Capacitor_SMD:C_0402_1005Metric | C7, C8, C9, C10, C11, C12, C13, C14 |
| 4 | LOGO | LOGO | G***, G***, G***, G*** |
| 3 | 10k | Resistor_SMD:R_0402_1005Metric | R2, R9, R11 |
| 3 | 1k | Resistor_SMD:R_0402_1005Metric | R1, R3, R8 |
| 3 | 5.1k | Resistor_SMD:R_0402_1005Metric | R4, R5, R10 |
| 2 | 15p | Capacitor_SMD:C_0402_1005Metric | C3, C4 |
| 2 | 1µ | Capacitor_SMD:C_0603_1608Metric | C1, C2 |
| 2 | 1µ | Capacitor_SMD:C_0402_1005Metric | C5, C6 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric | R6, R7 |
| 2 | Cirque | local-libraries:FPC-SMD_FPC05012-09200-.5mm | J6, J14 |
| 2 | NA_Conn_01x04_Female | Library:PinHeader_1x04_P2.54mm_Vertical_USB | J2, J3 |
| 2 | NA_Conn_01x04_Female | drawings:PinHeader_1x04_P2.54mm_Vertical | J4, J12 |
| 2 | NA_Jumper_2_Open | local-libraries:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | NA_JP1, NA_JP2 |
| 2 | NA_M4 | Library:MountingHole_4mm_Pad_Via | H1, H2 |
| 2 | NA_SW_SPST | Library:PushSwitch | SW1, SW2 |
| 2 | USBLC6-2P6 | Package_TO_SOT_SMD:SOT-666 | U2, U4 |
| 1 | B5817 | Diode_SMD:D_SOD-323 | D2 |
| 1 | Conn_01x02 | drawings:PinHeader_1x02_P1.27mm_Vertical | J5 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_2520-4Pin_2.5x2.0mm | Y1 |
| 1 | FerriteBead_Small | Inductor_SMD:L_0603_1608Metric | FB1 |
| 1 | G*** | kibuzzard-6208EFFE | kibuzzard-6208EFFE |
| 1 | G*** | kibuzzard-61F01B61 | kibuzzard-61F01B61 |
| 1 | LED | LED_SMD:LED_0402_1005Metric | D1 |
| 1 | NA_RGB | Library:header1x03 | J9 |
| 1 | NA_Ribbon | Library:5_PinHeader | J10 |
| 1 | NA_Ribbon | Library:6_PinHeader | J8 |
| 1 | NA_Serial | drawings:Jack_3.5mm_PJ320E_Horizontal_custom | J11 |
| 1 | NA_trackball | Library:6_PinHeader | J7 |
| 1 | Polyfuse | Fuse:Fuse_0603_1608Metric | F1 |
| 1 | RP2040 | 0xLib_Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1 |
| 1 | Serial | drawings:Jack_3.5mm_PJ320E_Horizontal_custom | NA_J6 |
| 1 | USB_C_Receptacle_USB2.0 | drawings:GT-USB-7014C | J1 |
| 1 | W25Q128JVS | drawings:W25Q128JVPIQ | U5 |
| 1 | XC6210B332MR-G | Package_TO_SOT_SMD:SOT-23-5 | U3 |
Questions
How big is the Splinktegrated PCB?
It measures 41.6 × 77.6 mm and has 2 copper layers, 1.2 mm thick.
What parts does the Splinktegrated use?
61 parts, built around the RP2040, W25Q128JVSIQ, USBLC6-2P6 and XC6210B332MR-G. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Splinktegrated KiCad files?
From the Bastardkb/splinktegrated repository on GitHub, at the commit this page was made from: the board is splinktegrated.kicad_pcb and its schematic splinktegrated.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Splinktegrated design in my own project?
Its repository states no licence, so its author keeps all rights: ask Bastardkb before reusing the design.
Similar boards
- 4 layers137 × 141 mm
- 2 layers
- 2 layers60 × 60 mm
Arcboard stm32-mk2
christrotter/arcboard-stm32-mk2
Next iteration of the stm32f405 board; paradigm shift means new repo.
94 partsMIT - 2 layers233.7 × 91.5 mm
Skywatch
ozkan/skywatch
35% ergonomic ortholinear keyboard, powered by RP2040, along with OLED and hotswap sockets support
133 parts41MIT - 2 layers125.5 × 95.1 mm
- 4 layers194.2 × 160 mm
- 2 layers134 × 95.1 mm
