Skip to the content
2 layers30.5 × 104.8 mmMoistureESP, the printed circuit board in 3D

ESP32 sensor project

Size
30.5 × 104.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
111
Nets
100
Pads
367
Tracks, vias
736, 201
Pours
14
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
29 Mar 2026
Updated
18 May 2026

Overview

MoistureESP is an open-source printed circuit board by balint603, from the balint603/MoistureESP_HW repository on GitHub. It is a 2-layer board of 30.5 × 104.8 mm with 111 parts on 100 nets, routed with 736 tracks and 201 vias.

It is built around the ESP32-WROOM-32, TPS7A2601DRVR and BQ28Z620DRZR, with the MAX77757JEFG420+, BC817W and RUM002N05T2L among its other parts. Its parts include 43 resistors, 27 capacitors, 10 transistors, 8 diodes and 7 connectors. It belongs with the ESP32 boards of this library.

Main components

12

README

README.md

Hardware for MoistureESP project.

Description

This project aims to use the ESP32 in low power modes, discover its capabilites for low power application. Also, this sensor project would be useful for home gardens not to forget watering. This is not a complete product, it can be considered as a devboard.

Software component not published yet. 3D case not published yet.

Software

See repository: https://github.com/balint603/moist

Components

  • This PCB project
  • ESP32-WROOM-32
  • SOILCAP-V20 humidity measure
  • DS18B20 sensor
  • SW not ready yet
  • BMS configuration not ready yet

Features

  • BMS cell protection.
  • Overvoltage protection for battery input.
  • Charger with USB (not tested).
  • Wi-Fi MQTT data transmission.
  • Selectable sensor measure interval.

Interfaces

  • Wi-Fi communication aimed to be used for sharing sensor data.
  • Analog input for moisture sensor board (SOILCAP-V20).
  • 1-Wire interface for DS18B20 temperature sensor.
  • BMS I2C lines.
  • UART for ESP programming and debug with RTS, DTS secondary programming feature.
  • Optional I2C for display.

Power

  • Sized for 18650 battery cell, BMS tested with NCR18650B.
  • Optinally Li-ion charger can be connected.
  • Built-in USB charger was not tested.

BMS configuration

  1. Disable 2 cell: Settings->DA configuration->CC0 bit needs to be set to zero.
    • Otherwise it causes CUV and discharge FET will not turn on.

Prerequisites

  • KiCAD v10.0.0

Release

  • V1.0: USB charger not tested.

Parts

111
QtyValueFootprintReferences
1810KResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR14, R15, R16, R23, R24, R26, R27, R28, R29, R30, R31, R34, R39, R40, R41, R42 +2
13100nFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC1, C2, C3, C4, C6, C7, C8, C9, C14, C15, C16, C19, C27
7100RResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR1, R3, R4, R10, R11, R13, R25
62.2uFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC5, C12, C13, C18, C20, C21
410uFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC22, C23, C24, C25
3BZT52H-AD3V3-QXDiode_SMD:D_SOD-123FD3, D6, D7
21.2MResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR18, R20
21.5MResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR17, R19
210MResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR5, R8
21uFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC10, C11
222uFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC17, C26
2470RResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR32, R33
25K1Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR6, R7
2BC817WPackage_TO_SOT_SMD:SOT-323_SC-70Q6, Q7
2ESD5ZxxDiode_SMD:D_SOD-523D1, D2
2Jumper_2_BridgedConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJP1, JP2
2LEDLED_SMD:LED_0603_1608MetricD4, D5
2MountingHoleMountingHole:MountingHole_2.7mm_M2.5_DIN965H1, H2
2RUM002N05T2LPackage_TO_SOT_SMD:SOT-723Q4, Q5
2SI7137DP-T1-GE3custom:MOSFET_7DP-T1-GE3_VISQ8, Q10
2SSM6K513NU-LFcustom:TRANS_SSM6K513NU-LFQ1, Q2
2TPS7A2601DRVRcustom:DRV0006AU2, U3
10RResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR37
111KResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR35
1147873-1custom:SW_147873-1SW1
115KResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR38
12.5AResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderF1
12N7002Wcustom:SOT65P220X100-3NQ3
12mRResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR2
14.7KResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR36
15.1KResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR21
1500mAResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderF2
15R1Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR12
18.1KResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR22
1BC856BLT1G0SCT-NDPackage_TO_SOT_SMD:SOT-23Q9
1BQ28Z620DRZRcustom:VSON12_DRZ_TEX-LU1
1BZT52H-B5V1Diode_SMD:D_SOD-123FD8
1Conn_01x02_PinConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ1
1Conn_01x03_PinConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ5
1Conn_01x04_PinConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ6
1Conn_01x06_PinConnector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalJ4
1Conn_DS18B20custom:sensorwirepads3x1J3
1Conn_MoisturePCBcustom:sensorwirepads3x1J2
1ESP32-WROOM-32RF_Module:ESP32-WROOM-32U4
1HTEK25201T-R47MSRInductor_SMD:L_1008_2520Metric_Pad1.43x2.20mm_HandSolderL1
1MAX77757JEFG420+custom:21-100385B_90-100128_MXMU5
1NCR18650Bcustom:NCR18650Batt1
1NTCG103JH103JT1Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderTH1
1NetTie_2NetTie:NetTie-2_SMD_Pad2.0mmNT1
1USB4110-GF-Acustom:USB4110-GF-A_GCTJ7

Similar boards

  • 2 layers96 × 40 mmLiIonUtilityBoard, the printed circuit board in 3D

    LiIonUtilityBoard

    Ilikemining1/LiIonUtilityBoard

    Small PCB with LiIon protection, charger, fuel gauge, and buck-boost output

    36 parts1
  • 2 layersIntegration, the printed circuit board in 3D

    Integration

    mickaelly01nobre/msp430fr2155-multisensor-lora-pcb-design

    O sistema foi projetado com foco em eficiência energética, comunicação sem fio e sensoriamento modular, sendo adequado para aplicações como monitoramento ambiental, agricultura inteligente e sensoriamento remoto.

    30 parts
  • 2 layers35.2 × 17.9 mmBluz lcd v1, the printed circuit board in 3D

    Bluz lcd v1

    Maniak003/BluZ

    Scintillation gamma-spectrometer

    97 parts3GPL-3.0
  • 2 layers13.5 × 13.1 mmPS400-4, the printed circuit board in 3D

    PS400-4

    Maniak003/radiation_indicator

    Индикатор радиации

    28 parts1
  • 4 layers99.2 × 56 mmPanel AB, the printed circuit board in 3D

    Panel AB

    sastles-com/isolation-sphere-solo-xiao

    球体 LED ディスプレイのファームウェア。server なし (solo) と server あり (配信) の両方を 1 つの バイナリで動かす。

    190 parts
  • 4 layers60 × 40 mmFtx, the printed circuit board in 3D

    Ftx

    SETIatHCRO/Front-Page

    Documentation related to the Allen Telescope Array at the Hat Creek Radio Observatory Wiki Link Below

    153 parts5
  • 4 layers60 × 40 mmFrx, the printed circuit board in 3D

    Frx

    EIGSEP/CAD

    106 parts

Questions

How big is the MoistureESP PCB?

It measures 30.5 × 104.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the MoistureESP use?

111 parts, built around the ESP32-WROOM-32, TPS7A2601DRVR, BQ28Z620DRZR and MAX77757JEFG420+. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the MoistureESP KiCad files?

From the balint603/MoistureESP_HW repository on GitHub, at the commit this page was made from: the board is MoistureESP.kicad_pcb and its schematic MoistureESP.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the MoistureESP design in my own project?

Its repository states no licence, so its author keeps all rights: ask balint603 before reusing the design.