2 layers22 × 30.5 mm
PedalIntermediate
rolfluc/VCR
Voltage Controlled Resistor for use as an intermediate to convert voltage into a resistance.
19 partsMIT
4 layers82.8 × 56.7 mm
State Mode Logic Analyzer
baldengineer/State-Mode-Logic-Analyzer8RP2040-Based Logic Analyzer that captures "state" mode
- Size
- 82.8 × 56.7 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 134
- Nets
- 116
- Pads
- 459
- Tracks, vias
- 1,090, 167
- Pours
- 17
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 20 Oct 2023
- Updated
- 12 Nov 2024
Overview
State Mode Logic Analyzer is an open-source printed circuit board by baldengineer, from the baldengineer/State-Mode-Logic-Analyzer repository on GitHub, published under the MIT licence. It is a 4-layer board of 82.8 × 56.7 mm with 134 parts on 116 nets, routed with 1,090 tracks and 167 vias.
It is built around the RP2040, 74LVC245APW and IS25LP128F-JBLE, with the 74HC4520D, AD5241BRZ1M and BZA856AVL among its other parts. Its parts include 40 resistors, 19 capacitors, 9 ICs, 7 diodes and 7 connectors. It belongs with the sensors and measurement boards and the RP2040 boards of this library.
Main components
7
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
74LVC245APW
TSSOP-20-40℃~+125℃ 8 Level translator Power-off protection、Output enable high-impedance TTL、CMOS Tri-State TSSOP-20 Buffers, Drivers, Receivers, Transceivers ROHSMDDBuffers, Drivers, Receivers, Transceivers
IS25LP128F-JBLE
SOIC-8-208mil-40℃~+105℃ 100,000 cycles 128Mbit 166MHz 2.3V~3.6V 20 Years 200us 8uA Power-on reset、Hardware write protection、Software write protection、Write enable latch、Power lock protection SPI SOIC-8-208mil NOR FLASH ROHSISSINOR FLASH
74HC4520D
SO-16-40℃~+125℃ 2 28ns 2V~6V 4 58MHz Asynchronous Binary Counter Falling Edge、Rising Edge Synchronous SO-16 Counters, Dividers ROHSNexperiaCounters, Dividers
AD5241BRZ1M
SOIC-14-30%~+50% -40℃~+105℃ 1 1MΩ 2.7V~5.5V 256 30ppm/℃ 60Ω、120Ω 9kHz I2C Linear Power-on reset SOIC-14 Digital Potentiometers ROHSAnalog DevicesDigital Potentiometers
BZA856AVL
SOT-353-5200nA 22pF 5.6V 6W ESD Four channels IEC 61000-4-2 Unidirectional SOT-353-5 ESD and Surge Protection (TVS/ESD) ROHSNexperiaESD And Surge Protection (TVS/ESD)
ECS-120-18-33-JEM-TR3
SMD3225-4P-20℃~+70℃ 100Ω 12MHz 18pF ±20ppm ±50ppm SMD3225-4P Crystals ROHSECSCrystals
README
README.mdEvery logic analyzer available today samples asychrnously. On slower systems this is needlessly wasteful.
This logic analyzer works as a state mode capture. A clock on the device-under-test (DUT) drives the capture.
More to come...
Parts
134| Qty | Value | Footprint | References |
|---|---|---|---|
| 37 | TestPoint_Harwin | My Libraries:Harwin-S1751-46-Test-Point | TP0, TP1, TP10, TP11, TP100, TP101, TP102, TP103, TP104, TP105, TP106, TP107, TP108, TP109, TP110, TP111 +21 |
| 16 | 220 | Resistor_SMD:R_0603_1608Metric | R25, R26, R27, R28, R29, R30, R31, R32, R33, R34, R35, R36, R37, R38, R39, R40 |
| 13 | 1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C4, C7, C8, C9, C11, C19, C20, C21, C22, C23, C24, C31 |
| 7 | 0 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R9, R11, R12, R13, R15, R18, R19 |
| 6 | 4k7 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R5, R6, R7, R8 |
| 4 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R4, R10, R14 |
| 3 | 10u | Capacitor_SMD:C_0805_2012Metric | C5, C10, C12 |
| 3 | DNP | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R20, R21, R22 |
| 3 | MountingHole | MountingHole:MountingHole_2.7mm | H1, H2, H3 |
| 2 | 27 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R16, R17 |
| 2 | 27p | Capacitor_SMD:C_0603_1608Metric | C1, C2 |
| 2 | 5k1 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R23, R24 |
| 2 | 74LVC245APW | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U10, U11 |
| 2 | DAC Disable | Jumper:SolderJumper-2_P1.3mm_Bridged2Bar_Pad1.0x1.5mm | JP4, JP5 |
| 1 | 1u | Capacitor_SMD:C_0805_2012Metric | C6 |
| 1 | 1v1 | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D3 |
| 1 | 2040_L0 | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D6 |
| 1 | 3v3 | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D2 |
| 1 | 5V | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1 |
| 1 | 5V USB0 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | 74HC4520D | Package_SO:TSSOP-16_4.4x5mm_P0.65mm | U3 |
| 1 | A0 | Jumper:SolderJumper-3_P1.3mm_Bridged2Bar12_Pad1.0x1.5mm | JP3 |
| 1 | AD0 | Jumper:SolderJumper-3_P1.3mm_Bridged2Bar12_Pad1.0x1.5mm | JP1 |
| 1 | AD1 | Jumper:SolderJumper-3_P1.3mm_Bridged2Bar12_Pad1.0x1.5mm | JP2 |
| 1 | AD5241BRZ1M | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U6 |
| 1 | Armed | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D4 |
| 1 | BZA856AVL | Package_TO_SOT_SMD:SOT-353_SC-70-5 | D7 |
| 1 | Boot 0 | Button_Switch_SMD:SW_SPST_PTS810 | SW2 |
| 1 | CLK Bypass | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP6 |
| 1 | ECS-120-18-33-JEM-TR | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | Exp In | Connector_PinSocket_2.54mm:PinSocket_2x10_P2.54mm_Horizontal | J4 |
| 1 | Exp Out | Connector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_Horizontal | J3 |
| 1 | G*** | My Libraries:BE5v2 | svg2mod |
| 1 | IS25LP128F-JBLE | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U7 |
| 1 | LTC6994xS6-1 | Package_TO_SOT_SMD:TSOT-23-6 | U4 |
| 1 | MCP1826S | Package_TO_SOT_SMD:SOT-223 | U9 |
| 1 | MCP4725 | Package_TO_SOT_SMD:SOT-23-6 | U5 |
| 1 | Probe | Connector_PinHeader_2.54mm:PinHeader_2x12_P2.54mm_Vertical | J5 |
| 1 | Probe Power | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J6 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1 |
| 1 | Reset 0 | Button_Switch_SMD:SW_SPST_PTS810 | SW1 |
| 1 | SWD0 | FTSH-105-01-L-DV-K:SAMTEC_FTSH-105-XX-X-DV | J7 |
| 1 | Triggered | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D5 |
| 1 | USB0 | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
The 132 most common of 134 parts.
Questions
How big is the State Mode Logic Analyzer PCB?
It measures 82.8 × 56.7 mm and has 4 copper layers, 1.6 mm thick.
What parts does the State Mode Logic Analyzer use?
134 parts, built around the RP2040, 74LVC245APW, IS25LP128F-JBLE and 74HC4520D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the State Mode Logic Analyzer KiCad files?
From the baldengineer/State-Mode-Logic-Analyzer repository on GitHub, at the commit this page was made from: the board is kicad/state mode logic analyzer.kicad_pcb and its schematic kicad/state mode logic analyzer.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the State Mode Logic Analyzer design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 4 layers163 × 174.4 mm
Gd rev3b
baldengineer/Mega-IIe
Using the Mega II from a IIgs to make a Apple IIe compatible computer: The Mega IIe!
440 parts33MIT - 2 layers190 × 100 mm
- 4 layers40 × 40 mm
- 4 layers40 × 40 mm
Pq obc comms
abelwu2001/Picosat-Pocketcube-UTN-FRC-2026
Proyecto Final para el armado de un nanoSat
68 parts3 - 2 layers90 × 56.8 mm
- 2 layers234 × 87.3 mm
V0c
KITTY-6502/hardware
the KITTY is a 65c02 homebrew kit microcomputer designed around text mode graphics and cartridge media. It is fully open source, and uses exclusively in-production parts.
123 parts - 4 layers130 × 64.3 mm
Tspico v2.6
timex-sinclair-projects/tspico-hardware
Status 2026-10-19: prototype 3 (v3.0-proto3, changes below). Proto1 (v3.0-proto1) was built and brought up; proto2 added its fixes (below).
93 partsCERN-OHL-S-2.0